Cyberparasite Posted January 16, 2006 Posted January 16, 2006 DFI LANPARTY UT nF4 SLI EXPERT - 12/07/05 BIOS[/url] AMD Opteron 150 Venus CABGE 0534SPMW 2x512MB G.Skill PC3200 GBLE (F1-3200DSU2-1GBLE) 2*eVGA 7800GT CO 256MB, 470/1100 81.98 drivers Seagate ST3250823AS SATA Lite-On Combo SOHC-5235 CDRW OCZ PowerStream OCZ520ADJ ATX 520W Power Supply [/url] ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Auto CPU VID Control - 1.475v CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.62v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB: 01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + Everest 2.20: http://home.midmaine.com/~rachelm/dfiocdb1gle.jpg 3dMark2003: http://home.midmaine.com/~rachelm/dfi031gle.jpg 3dMark2005: http://home.midmaine.com/~rachelm/dfi051gle.jpg ========== short description: 300x10 @ 3000Mhz, 1.475v + 104% 2.5-3-8-3 @ 2.8v vdimm Share this post Link to post Share on other sites More sharing options...
Redbeaver Posted January 18, 2006 Posted January 18, 2006 DFI Infinity SLI 08312005 BIOS AMD Athlon64 3200+ Venice ADA3200DAA4BP 90nm SOI 2x512MB OCZ Performance Series rev. 3 pc 3200 (strangely tccd) eVGA 7800GT CO 256MB 490/1175 82.12 drivers Western Digital Caviar SATA II (WD2500KS) 250GB 7200RPM 16MB Buffer Pioneer DVR-110D DVD-writer 8x Enermax Liberty 500W ATX 12V Ver2.2 * * ========== [b]Genie BIOS Settings:[/b] [color=red] CPU Frequency....................... - 311Mhz Hammer FID Control.................. - x9 HT Frequency........................ - 3x HT Width............................ - 16/16 PCI-E Clock......................... - 100Mhz DDR Voltage Control................. - 2.7v Chip Voltage Control................ - 1.7v CPU Voltage Control................. - 1.675v [/color] [b]DRAM Configuration[/b] [color=red] Timing Mode......................... - Manual Memclock Mode....................... - Limit Memclock Index Value (Mhz).......... - 133Mhz CPU: DDR 1:6 CAS# Latencly (Tcl)................. - 2 Min RAS# Active Time (Tras)......... - 6T RAS# to CAS# Delay (Trcd)........... - 3T Row Precharge Time (Trp)............ - 3T Row to Row Delay (Trrd)............. - 3T Row Cycle Time (Trc)................ - 8T Row Refresh Cycle Time (Trfc)....... - 16T Write Recovery Time (Twr)........... - 3 bus clock Write-to-Read Delay (Twtr).......... - 2 bus clock Read-to-Write Delay (Trwt).......... - 3 bus clock Refresh Rate (Tref)................. - 3120 Cycle DDR Output Driving.................. - Auto DDR DQ Drive Strenght............... - Auto User Config mode.................... - Manual Bottom of 32-bit[31:24] IO.......... - B0 1T/2T Memory Timing................. - 1T Read Preamble Value................. - 5.5ns Asynch Latency Value................ - 7ns Dynamic Idle Cycle Counter.......... - Auto DRAM Bank Interleaving.............. - Enabled Burst Length........................ - 4 Beats Enable All DIMM Clock............... - Enabled S/W Memory Hole Remapping........... - Disabled H/W Memory Hole Remapping........... - Disabled MTRR Mapping Mode................... - Continuous [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.31: http://trsuploader.gtahoodz.com/images/pic1.JPG 3dMark2003: http://trsuploader.gtahoodz.com/images/pic2.JPG 3dMark2005 + Everest 2.02: http://trsuploader.gtahoodz.com/images/pic3.JPG ========== short description: 311x9 @ 2814Mhz, 1.6500V 2-3-3-6-1T DDR402 @ 2.7V vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted January 20, 2006 Posted January 20, 2006 DFI LANPARTY nF4 Expert SLI-DR (12/07/2005 BIOS) AMD X2 4400+ dual core 2x1024MB OCZ PC4000GXC (OCZ5001024ELGEGXT) XFX GeForce 7800GTX, 505/1340 81.89 drivers 3x 80GB Hitachi SATA II hdd - RAID-0 Asus 52x Quiet-Trak CD-ROM OCZ Powerstream 600w psu * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - x 10.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.425v CPU VID Special Control....................... - 102.4% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.59v DRAM Voltage Control.......................... - 2.87v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - By DRAM SPD Value Command Per Clock (CPC)....................... - Auto CAS Latency Control (Tcl)..................... - Auto RAS# to CAS# delay (Trcd)..................... - Auto Min RAS# active time (Tras)................... - Auto Row precharge time (Trp)...................... - Auto Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/nf4/e...gx_250x10-1.gif 3dMark2003: 3dMark2005: Aquamark 3d: 3dMark 2006: ========== short description: 250x10 @ 2500Mhz, 1.425v + 102.4% 3-4-7-3 @ 2.87v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted January 20, 2006 Posted January 20, 2006 DFI LANPARTY nF4 SLI-DR (7/04-2BTA BIOS) AMD 4000+ San Diego 2x1024MB OCZ PC4000EB (OCZ5001024EBPE) GeForce 6800GT, 397/1105 81.89 drivers 36GB Western Digital Raptor 10,000RPM SATA hdd Asus 52x Quiet-Trak CD-ROM Skyhawk 520w Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - x 11.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.550v CPU VID Control............................... - 1.425v CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/lou/lou_250x10-1.gif 3dMark2003: 3dMark2005: Aquamark 3d: 3dMark 2006: ========== short description: 250x11 @ 2750Mhz, 1.425v + 110% 3-3-8-2 @ 2.70v vdimm special thanks to Lou aka burleyboy for letting me use his hardware to enter this! Share this post Link to post Share on other sites More sharing options...
saruman Posted January 21, 2006 Posted January 21, 2006 DFI LANPARTY nF4 Expert SLI-DR (11/02/05 BIOS) Opteron165 Dual Core Cpu CCBWE 0534MPMW G.Skill F1-4000USU2-2GBHZ 2 Gig Kit 3-4-4-8 @ 554 Mhz (277 Mhz FSB) 7800GT GFX (o/clocked core 500 Mhz, memory 1.2 Ghz) 82.12 Drivers 550W Antec TP 2.0 EPS Stock CPU Cooler 2 x 250 GIG WD SATA2 16Meg Cache HDD RAID0 Windows XP64 Pro SP1 ========================================================== Bios http://img43.imageshack.us/img43/1309/12cf1.jpg http://img43.imageshack.us/img43/5395/27ko.jpg http://img43.imageshack.us/img43/2509/30pp.jpg http://img43.imageshack.us/img43/173/41or.jpg -------------------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------------------- prime95+3dmark2001+everest+cpu-z http://img4.imageshack.us/img4/5002/dualpr...150012gfx4i.jpg 3dmark03 http://img4.imageshack.us/img4/3151/3dmark03htt2771013rz.jpg 3dmark05 http://img4.imageshack.us/img4/4518/3dmark05htt2771010jb.jpg -------------------------------------------------------------------------------------------------------- short description: 277x9 @ 2493Mhz, 1.40v 3-4-4-8 @ 2.71v vdimm Share this post Link to post Share on other sites More sharing options...
Blackhorn Posted January 22, 2006 Posted January 22, 2006 DFI LANPARTY UT nF4 SLI-DR Expert 12/7 BIOS AMD Athlon64 3000+ Venice OCZ Gold GX 2GB (2 x 1GB) 184-Pin DDR SDRAM (UCCC) eVGA 256-P2-N517-AX Geforce 7800GT 256MB , Version: 81.98 drivers 2x Seagate Barracuda 7200.7 ST380817AS 80GB 7200 RPM 8MB Cache Serial ATA150 Hard Drive (8MB cache) - RAID 0 ASPIRE ATX-AS520W BLACK ATX 520W Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 2.5 CPU/FSB Frequency Ratio - 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.550v CPU VID Special Control - Above VID * 102.4% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.52v DRAM Voltage Control - 2.79v DRAM Configuration Settings: DRAM Frequency Set - 1=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - AutoAuto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://home.rochester.rr.com/malleolus/ima...0p95%20ever.jpg 3dMark2003: 3dMark2005: ========== short description: 300x9 @ 2700Mhz, 1.550v + 102.4% 3-4-8-3 @ 2.79v vdimm Share this post Link to post Share on other sites More sharing options...
Praz Posted January 22, 2006 Posted January 22, 2006 UT nF4 SLI-DR Expert - 11/02/05 BIOS AMD Athlon 64 3200+ Venice G.SKILL Extreme Series 2GB DDR 500 F1-4000USU2-2GBHZ eVGA e-GeForce 6800 GS PCI Express, 500/1270 81.85 drivers Maxtor Maxline III 7L300S0 300GB Serial ATA 1.5Gb 7200RPM Hard Drive w/16MB Buffer Liteon SOHW-1693S 16X Dual Layer DVD±RW Drive (Black) OCZ ModStream OCZ52012U ATX, BTX, SATA, P4 and EPS12V 520W Power Supply Scythe SCNJ-1000 Ninja Heatpipe CPU Cooler + Nexus 120 mm Real Silent Case Fan Black/White Zalman VF700-CU VGA Cooler ========== Genie BIOS Settings: FSB Bus Frequency - 266 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.400v CPU VID Control - 1.500v CPU VID Special Control - Above VID * 102.4% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.52v DRAM Voltage Control - 2.56v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 03 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 13 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3684 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 5 DRAM Data Drive Strength - Level 1 Max Async Latency - 7.0 Nano Seconds DRAM Response Time - Fastest Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.50.480: 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 266x10 @ 2660Mhz, 1.50v + 102% 3-4-4-7 1T @ 2.56v vdimm Share this post Link to post Share on other sites More sharing options...
RGone Posted January 22, 2006 Posted January 22, 2006 DFI SLI-DR EXPERT Mother board with Beta Bios 11/25/05. OEM FX-55 processor. 0515. XfX 7800GTX Video Card with 81.87 Drivers. SunBeam 550watt NUUO power supply. Corsair TwinX2048/3500LLPro 2x1gig. Orange Slots. 2x37.4gig Raptors in Raid 0 NVraidRom "Booting". 1x Maxtor 200gig PATA 133. 1x Maxtor 15gig PATA 100. 1x Lite-On Dual Layer DVD/RW. 1x Mitsumi 1.44 Floppy drive. Thermalright XP-90 W/Delta 3 blade 4K RPM 78.4 CFM (on power supply lead). Nvidia 6.66 Driver set using Nvidia Ethernet and onboard sound. [b]Genie BIOS Settings:[/b] [color=red]FSB Bus Frequency............................. - 220 LDT/FSB Frequency Ratio....................... - x 4.0 CPU/FSB Frequency Ratio....................... - x12 PCI eXpress Frequency......................... - 102Mhz CPU VID StartUp Value......................... - 1.425v CPU VID Control............................... - 1.350v CPU VID Special Control....................... - Above VID * 112.0% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.65v DRAM Voltage Control.......................... - 2.69v [/color] [b]DRAM Configuration Settings: Memory ORANGE Slots.[/b] [color=blue]DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.0 RAS# to CAS# delay (Trcd)..................... - 3.0 Min RAS# active time (Tras)................... - 08.0 Row precharge time (Trp)...................... - 2.0 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 19 Bus Clocks Row to Row delay (Trrd)....................... - 04 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 RAM DLL SPEED................................. - Auto DRAM Drive Strength........................... - Level 7 DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - 09.0ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 6.0ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 05 x 32 Byte Granularity........................... - Disable(4 Bursts)[/color] Prime and 3d01 3d03 and 05 In general it is FX-55 Using Corsair PC3500LL Pro 2x1gig sticks at 1T; slightly overclcocked with a 12 multiplier for an 'easy' 2640Mhz and tight timings. With a raid 0 array. RGone... Share this post Link to post Share on other sites More sharing options...
nitemareglitch Posted January 25, 2006 Posted January 25, 2006 DFI Expert 12/07/05 bios AMD Athlon64 3500+ Venice 2x1gb G.Skill F1-4000USU2-2GBHZ Evga 7800GT 256MB, 470x1100 81.98 drivers 2x WD Raptor 36gb Raid 0 PLEXTOR DVDR PX-716A OCZ PS 600w ================= Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 112.0% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.59v DRAM Voltage Control - 2.71v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.30 + Everest 1.51: http://img.photobucket.com/albums/v284/nit...ld/OC_Entry.jpg 960x768 3dMark2003: 3dMark2005: ========== short description: 260x10 @ 2600Mhz, 1.400v + 112% 3.0 4-4-8-7 2.71v Share this post Link to post Share on other sites More sharing options...
LDog69 Posted January 25, 2006 Posted January 25, 2006 DFI LANPARTY nF4 Ultra-D - 7/04-2BTA BIOS w/SLI Mod, 6.70 drivers AMD Athlon64 X2 3800+ Manchester 2x512MB OCZ Gold EL DDR500 Gigabyte 6600GT 128MB, 550/1100 81.98 drivers 2 x Western Digital 80GB SATA hdd (8MB cache; RAID-0) Lite-On DVD-RW Drive Enermax DVD-RW/DL Drive OCZ ModStream ATX 520W Power Supply ThermalTake Venus12 CPU Cooler w/AS5 ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - x 4.0 CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.475v CPU VID Special Control - AUTO LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - AUTO DQS Skew Value - 0 DRAM Drive Strength - AUTO DRAM Data Drive Strength - AUTO Max Async Latency - AUTO DRAM Response Time - Normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - AUTO Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + Everest 2.20: http://admin.g-status.com/images/ocdb/ocdb-260x10-s1.PNG 3dMark2003: 3dMark2005: ========== short description: 260x10 @ 2600Mhz, 1.475v 2.5-3-7-3 @ 2.8v vdimm (Orange Slots) 6600GT @ 550Mhz/1100Mhz Share this post Link to post Share on other sites More sharing options...
Chum Posted January 27, 2006 Posted January 27, 2006 DFI LANPARTY nF4 Ultra-D - 7/04-2 BigToe BIOS AMD Opteron 165 Denmark (CCBWE 0547 TPMW) 2x1024MB OCZ Gold PC4000 eVGA 7800GT 256MB, 508/1200 81.98 drivers WD Raptor 74GB 10K SATA (8MB cache) NEC 3550A Black IDE DVD+/-RW Drive Enermax Liberty ATX 500W Power Supply - Retail ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.350v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 24 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://users.adelphia.net/~chum/images/chum1.JPG 3dMark2003: 3dMark2005: 3dMark2006: ========== short description: 300x9 @ 2700Mhz, 1.350v + 110% 3-4-8-4 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
TheFlowerKing Posted January 28, 2006 Posted January 28, 2006 DFI LANPARTY nF4 Ultra-D - 704-2BTA Bios AMD Opteron 170 CCBWE 0550UPMW on Big Typhoon 4x512 Geil TCCD (Ultra-X (Yellow) One S (Orange)) Connect3D X800GTO mod 16 pipelines, 560/1080 5.11? drivers Samsung 80Gb SATA hdd (8MB cache) FSP BlueStorm 460W psu ========== Genie BIOS Settings: FSB Bus Frequency - 262 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.325v CPU VID Special Control - 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.70v +0.03v - Enable DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/1 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3072 Cycles DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Dual Prime95 + 3dMark2001SE (29915) + CPU-Z 1.30 (voltage reading in cpu-z is truly 1.440v): http://img490.imageshack.us/img490/7379/du...cpuzvoltisa.jpg 3dMark2003 (13919) + Everest 1.51 Memory Read (4947): http://img465.imageshack.us/img465/5483/3d...readis49476.jpg 3dMark2005 (6736) + Everest 1.51 Memory Write (2394): http://img465.imageshack.us/img465/7513/3d...riteis23941.jpg ========== short description: 262x10 @ 2620Mhz, 1.497v 4x512Mb @ 262MHz @ 2.5-3-5-3 @ 2.73v Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now