petercintn Posted March 26, 2006 Posted March 26, 2006 DFI LANPARTY nF4 Ultra-D - 03/29/06 AMD Opteron 146 CACJE 0603FPMW 2x1GB Mushkin Black (uccc) EVGA 7800GT 256MB, 506/1220 Maxtor 160GB IDE hdd OCZ PowerStream OCZ520ADJ ATX 520W Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 288 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Auto CPU VID Control - 1.425 CPU VID Special Control - 104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.50v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - 15 Bus Clocks Row to Row delay (Trrd) - 01 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Increase Skew DQS Skew Value - 32 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 10 DRAM Response Time - Fast Read Preamble Time - 8.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 06 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 3dMark2003: 3dMark2005: Everest: OCCT CPU core temp graph (fans on low): short description: 288x10 @ 2880Mhz, 1.425vid x 104% 3.0-4-8-3 @ 2.5v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted March 27, 2006 Posted March 27, 2006 DFI Lanparty SLI-D - Bios 11/14/05 Opteron 144 CAB2E 0546UPMW 2x1024 Crucial Ballistix z503's (Orange Slots) Power Color x850xt STOCK w/6.3cats 2x 74gig Raptor Raid0 NEC 3550a DVD drive OCZ 600w Power Stream SLI Edition DangerDen = TDX + Maze4 + BIX2 + DDC-12v + 38 tubing * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.45v CPU VID Control - 1.45v CPU VID Special Control - 110% LDT Voltage Control - 1.3v Chip Set Voltage Control - 1.6v DRAM Voltage Control - 2.6v DRAM Configuration Settings: DRAM Frequency Set - 180 (9:10) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 3 Bus Clocks Min RAS# active time (Tras) - 8 Bus Clocks Row precharge time (Trp) - 3 Bus Clocks Row Cycle time (Trc) - 9 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 3 Bus Clocks Write recovery time (Twr) - 3 Bus Clocks Write to Read delay (Twtr) - 2 Bus Clocks Read to Write delay (Trwt) - 3 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + 2x CPU-Z + MBM + a64tweaker : 3dMark2003 + Everest Reads + MBM + 2x CPU-Z : 3dMark2005 + Everest Writes + MBM + 2x CPU-Z : 3dMark2006 + Everest Latency + MBM + 2x CPU-Z : ========== short description: 300x9=2700mhz 3-3-8-3-9-16 2.6vdimm @ 270mhz Share this post Link to post Share on other sites More sharing options...
OldGuy Posted March 28, 2006 Posted March 28, 2006 LanParty NF4 Ultra D - BIOS 704-2BTA AMD Opteron 150 Venus 2GB (2X512 Patriot 3200+XBLK tccd plus 2X512 Geil One tccd) XFX 7900GTX 512MB - 665/1630 84.25 beta drivers Hitachi Deskstar 80gb SATA II X2 RAID 0 (8MB cache) NEC ND-3520A DVD-RRW Enermax EG701AX-VE SFMA 600W Thermalright XP-90 HS * * ========== Genie BIOS Settings: FSB Bus Frequency - 264 LDT/FSB Frequency Ratio - X 4.0 CPU/FSB Frequency Ratio - X 11.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.400v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 24 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Weak 4 DRAM Data Drive Strength - Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: 3dmark 2006: Aquamark 3d: Everest Read: Everest Write: Everest Latency: Sandra Bandwidth: ========== short description: 264 X 11 @ 2904 Mhz, 1.400v + 113% 2.5-4-7-3 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
Clay Posted March 31, 2006 Posted March 31, 2006 Ohh... I hope I did this right. These are my best results at these settin's. DFI LANPARTY nF4 Ultra-D - 7/04-2 BigToe BIOS AMD Opteron 148 CACJE 0601 2x512MB OCZ Platinum limited editon DDR600 (tccd) Evga 7900GT 256MB, 500/1500 83.91 drivers 1# Western-Digital Raptor2 74GB 10000rpms (8MB cache) ASUS Black IDE DVD DL RAM Drive OCZ PowerStream OCZ520ADJ SLI ATX 520W Power Supply - Retail ========== Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.375v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.6 +.003 (2.71 board sensor)v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:10/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4196 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Enabled R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z v1.32 (Toaster Screenie): 3dMark2003: 3dMark2005: 3dmark2006: Aquamark 3d: Everest v220: Reads: Writes: Latencies: Best superpi's (W/these settin's)and A64 tweaker,Sandra-memory bench.: ========== short description: 290x10 @ 2900Mhz, 1.375v + 113%(Normally 1.35*110) Needed more for prime only. 2.5-3-7-3 @Bios 2.60+.003 enabled Board sez 2.71v vdimm though. I think I got kinda' lucky on my sticks,and processor. Share this post Link to post Share on other sites More sharing options...
kainne Posted April 1, 2006 Posted April 1, 2006 DFI LANPARTY nF4 Ultra-D | 6/23-2 TMod BIOS AMD Opteron 144 Venus CACJE 0603GPBW 2x1GB G Skill HZ DDR500 F1-4000USU2-2GBHZ (UCCC) Connect3d x800GTO 256MB, 400/490 Cat 6.3 drivers Western Digital SE 80GB SATA II HD (8MB cache) Hitachi SE 80GB SATA II HD (8MB cache) NEC 16X DVD±R DVD Burner ND-3550A Solytech SL-D460EXP ATX12V 460W PSU * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.125v CPU VID Special Control - Above VID * 136% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.60v +0.03 vdimm - Disabled DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trtw) - 02 Bus Clocks Refresh Period (Tref) - 0780 Cycles Write CAS Latency (Twcl) - 01 Bus Clock DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.32.1 + Everest Home (Memory Read): Prime95 + 3dMark03 + CPU-Z 1.32.1 + Everest Home (Memory Write): Prime95 + 3dMark05 + CPU-Z 1.32.1 + Everest Home (Memory Latency): ========== 300x9 @ 2700Mhz, 1.125v + 136% 3-4-4-8 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
Voltes-5 Posted April 2, 2006 Posted April 2, 2006 DFI LANPARTY nF4 Expert (12/7/05 BIOS) AMD Opteron 165 CCBWE 0551VPMW 2x1024 Crucial Ballistix Z503.16TD1 PC4000 BFG GeForce 7800GT OC, 81.95 driver 2x Maxtor DiamondMax10 SATA RAID0 striped Lite On SOHW-1633S PC P&C 510 ASL DangerDen D4 Pump / Copper TDX Waterblock (lapped) ========== Genie BIOS Settings: FSB Bus Frequency - 310 LDT/FSB Frequency Ratio - 3.0 CPU/FSB Frequency Ratio - 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.475v CPU VID Special Control - Above VID * 112% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.68v DRAM Voltage Control - 2.87v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 3 Bus Clocks Min RAS# active time (Tras) - 8 Bus Clocks Row precharge time (Trp) - 3 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 016 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 3dMark2003: 3dMark2005: Everest Read/Write/Latency ========== short description: 310x9 @ 2790Mhz, 1.475v + 112% 3-3-8-3 @ 2.87v vdimm Share this post Link to post Share on other sites More sharing options...
Kwame Posted April 5, 2006 Posted April 5, 2006 DFI LANPARTY nF4 Ultra-D - 3/29 AMD Athlon64 x2 4200+ Manchester 2x1gB OCZ PC3200 GX XTC (Infineon) MSI 7800GT 256MB, 465/1170 84.21 drivers Maxtor 200GB SATA hdd (8MB cache) Maxtor 40GB IDE hdd (2MB cache) * * ========== Genie BIOS Settings: FSB Bus Frequency - 237 LDT/FSB Frequency Ratio - 4 CPU/FSB Frequency Ratio - 11 PCI eXpress Frequency - 105Mhz CPU VID StartUp Value - Auto CPU VID Control - 1.550v CPU VID Special Control - Auto LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.50v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:10/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 10 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3072 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 6 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== SP2004 + 3dMark2001SE + CPU-Z 1.33 + Everest 2.20: 3dMark2001SE: 3dMark2003: 3dMark2005: ========== short description: 237x11 @ 2630Mhz, 1.550v 3-3-8-2 @ 2.5v vdimm Share this post Link to post Share on other sites More sharing options...
Guest Synchronize Posted April 5, 2006 Posted April 5, 2006 DFI LANPARTY nF4 SLI-D - 6/23/2005-3 BIOS (T-Mod) Opteron 146 Venus Socket 939 CABYE 0540FPAW Stepping 2GB Corsair Twin-x 4000PT 2x Asus 7800GTX's 256mb 84.25 drivers Not WHQL (470/1301) 2xMaxtor Sata Diamond-max10 200GB (Raid-0) HP DVD-/RW +/- 16x Lightscribe Jeantech Arctic 600w PSU Thermaltake VA8000SWA Armour (Silver) Zalman CNPS9500 LED * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.5 CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.6 + DRAM+.03v if it's not 3.2v - Enable DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:5/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Enabled R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95(Small FFT's) + 3dMark2001SE + CPU-Z 1.32.1 http://i7.photobucket.com/albums/y271/sync.../OCDB-3GHZ2.jpg SP2004(Blend) + 3dMark2001SE + CPU-Z 1.32.1 http://i7.photobucket.com/albums/y271/sync...B/OCDB-3GHZ.jpg 3DMARK03: 3DMARK05 Everest Read(1.51) Everest Read(2.20) ========== short description: 300x10 @ 3000Mhz, 1.5v + 104% 3-4-8-4 @ 2.65v vdimm Share this post Link to post Share on other sites More sharing options...
Praz Posted April 7, 2006 Posted April 7, 2006 LANPARTY UT NF4 SLI-DR Venus - 03/07/06 BIOS AMD Opteron 170 G.SKILL Extreme Series 2GB DDR 500 F1-4000USU2-2GBHZ eVGA e-GeForce 6800 GS PCI Express, 500/1270 83.40 drivers Maxtor Maxline III 7L300S0 300GB Serial ATA 1.5Gb 7200RPM Hard Drive w/16MB Buffer Liteon SOHW-1693S 16X Dual Layer DVD±RW Drive (Black) OCZ PowerStream OCZ520ADJSLI ATX, BTX, EPS12V 520W Power Supply Swiftech STORM Extreme Performance Universal Water-block - Rev 2 Swiftech MCP655 Pump Black Ice Pro III Triple 120mm Radiator With D12SL-12 YATE LOON 120mm Case Fans Chipset Cooled By Evercool VC-RE VGA Cooler Zalman VF700-CU VGA Cooler [b]Genie BIOS Settings:[/b] [color=navy] FSB Bus Frequency..................... 295 LDT/FSB Frequency Ratio............... 3.0x CPU/FSB Frequency Ratio............... 10x PCI Express Frequency................. 100 CPU VID Startup Value................. 1.350 CPU VID Control....................... 1.450 VID Special Control................... 107.2% LDT Voltage Control................... 1.20V Chip Set Voltage Control.............. 1.52v Dram Voltage Control.................. 2.56v[/color] [b]DRAM Configuration Settings:[/b] [color=darkgreen] Dram Frequency Set (Mhz).............. 166=RAM/FSB:05/06 Command Per Clock (CPC)............... Enable CAS# latency (Tcl).................... 3.0 RAS# to CAS# delay (Trcd)............. 04 Min RAS# active time (Tras)......... . 08 Row Precharge Time (Trp).............. 04 Row Cycle Time (Trc).................. 07 Row refresh timg (Trfc)............... 14 RAS# to RAS# delay (Trrd)............. 02 Write Recovery Time (Twr)............. 02 Wite-to-Read Delay (Twtr)............. 01 Read-to-Write Delay (Trwt)............ 03 Refresh Rate (Tref)................... 3684 Cycles Write CAS Latency (Twcl)...............01 DRAM Bank Interleaving................ Enabled DQS Skew Control...................... Auto DQS Skew Value........................ 0 DRAM Drive Strength................... Level 05 DRAM Data Drive Strength.............. Level 1 Max Asynchronous Latency.............. 08.0 DRAM Response Time.....................Fastest Read Preamble Time.................... 06.0 IdleCycle Limit........................256 Dynamic Counter....................... Enable R/W Queue Bypass.......................16X Bypass Max.............................07X 32-Byte Granularity................... Disable (4 bursts) [/color] Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: X3 Demo With Dual Super_Pi short description: 295x10@ 2950Mhz, 1.450v + 107.2% 3-4-4-8 @ 2.56v vdimm Share this post Link to post Share on other sites More sharing options...
TheFlowerKing Posted April 7, 2006 Posted April 7, 2006 DFI LANPARTY nF4 Ultra-D - 0329 Bios AMD Opteron 170 CCBWE 0550UPMW on stock heatpipe cooler 2x256Mb + 2x512Mb Mushkin LII BH-5 (old school) Connect3D X800GTO mod 16 pipelines, 560/1080 5.13 drivers Samsung 80Gb ATA hdd (8MB cache) Enermax 535w psu ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - 4 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.500v CPU VID Special Control - AUTO LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.60v +0.03v - Disable DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/1 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 7 DRAM Data Drive Strength - 2 Max Async Latency - 7ns DRAM Response Time - Normal Read Preamble Time - 5ns IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Dual Prime95 + 3dMark2001SE (30277) + CPU-Z 1.32.1 : http://img360.imageshack.us/img360/2105/du...1is302772yk.jpg 3dMark2003 (13955) + Everest 1.51 Memory Read (5105): http://img360.imageshack.us/img360/2654/3d...treadis5105.jpg 3dMark2005 (6738) + Everest 1.51 Memory Write (2229): http://img485.imageshack.us/img485/7360/3d...riteis22292.jpg ========== short description: 260x10 @ 2600Mhz, 1.500v 2x256Mb + 2x512Mb @ 260MHz @ 2-2-5-2 @ 3.60v Share this post Link to post Share on other sites More sharing options...
pharmd24 Posted April 9, 2006 Posted April 9, 2006 DFI RS482 INFINITY (3/21/2006 BIOS) AMD Opteron 144 Venus 1MB L2 2x512MB PC3200 Mushkin LVL2 V2 (TCCD) ATI x850XT PE 256mb, 540/590 6.3 drivers 250GB Seagate SATA hdd NEC 3500A Silver IDE DVD-RW Drive Antec TRUEPOWERII TPII-550 550W Power Supply ========== [b]Genie BIOS Setting:[/b] [color=red] DLL Speed Override............................ - Auto DLL Speed..................................... - High CPU/FSB Ratio Setting......................... - x9 CPU'n'NB Bus Ratio SEtting.................... - x3 600 MHz CPU Clock Setting............................. - 300 O.C. Failed Control........................... - Disabled DRAM Clock Setting............................ - 6/5 PCIE Clock Setting............................ - 100MHz CPU Voltage Setting........................... - 1.475v DRAM Voltage Setting.......................... - 2.9v NB and HT Voltage Setting..................... - 1.3v NB-SB Link Voltage Setting.................... - 1.9v Auto Detect PCI Clk........................... - Enabled Spread Spectrum............................... - Disabled [/color] [b]DRAM timing and Config:[/b] [color=red] CAS latency(tCL).............................. - 2.5 Min RAS active time(tRAS)..................... - 8T RAS to CAS delay(tRCD)........................ - 3T Row precharge Time(tRP)....................... - 3T Row to Row delay(tRRD)........................ - 2T Row Cycle time(tRC)........................... - 10T Row refresh CYC Time(tRFC).................... - 24T Read to Write time(tRWT)...................... - 2T Refresh Rate(tREF)............................ - 1560 Cycles Write to Read Delay(tWTR)..................... - 2 Bus Clocks Write recovery Time tWR)...................... - 2 Bus Clocks 1T/2T Memory Timing........................... - 1T Read Preamble value........................... - 5.5ns Async Latency value........................... - 7ns DRAM Drive Strength........................... - Weak Dram Drive Strength Ratio..................... - x1.28 DRAM DQ Drive Strength........................ - 50 % DQS Hysteresis................................ - Disabled Read and Write Queue Bypass................... - Auto Dynamic Idle Cycle Counter.................... - Enabled Idle Cycle Limit.............................. - 16 Cycles Bypass Max.................................... - 4 Times Odd Divisor Correct........................... - Disabled Dual DIMM..................................... - Auto Disable Jitter................................ - Auto DRAM Bank Interleave.......................... - Enabled Burst Length.................................. - 8 beats Enable AllDIMM slots clock.................... - Enabled MTRR mapping mode............................. - Continuous PDL Delay Adjust.............................. - Auto [/color] [b]System Bus Configuration:[/b] [color=red] HT Link Configuration......................... - Enabled Upstream LDT Bus Width........................ - 16 bit Downstream LDT Bus Width...................... - 16 bit [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.33: http://img.photobucket.com/albums/v318/pharmd24/DFI/2.jpg 3dMark2003: 3dMark2005: EverestMemory Read: http://img.photobucket.com/albums/v318/pha...I/everestMR.jpg ========== short description: 300x9 @ 2700Mhz, 1.475v 2.5-3-8-3 @ 2.9v vdimm Share this post Link to post Share on other sites More sharing options...
olympic Posted April 11, 2006 Posted April 11, 2006 DFI LANPARTY nF4 SLI-DR -623-3 BIOS AMD Opteron 170 CCB1E 0550VPMW 2x1024MB OCZ PC3200 Platinum EVGA 7800GTX 256MB(water cooled,custom BIOS), 513/1400 81.98 drivers Western Digital Raptor 74GB Western Digital Caviar SE 250GB Antec Truepower 2.0 Truecontrol II-550 ATX12V 550 watt PSU Swiftech H20-220 Apex Extreme water cooling kit * * ========== Genie BIOS Settings: FSB Bus Frequency - 285 LDT/FSB Frequency Ratio - x3 CPU/FSB Frequency Ratio - x10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.425v CPU VID Special Control - auto LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 150=RAM/FSB:3/04 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 7 Bus Clocks Row refresh cyc time (Trfc) - 10 Bus Clocks Row to Row delay (Trrd) - 01 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 01 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 1 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: ========== short description: 285x10 @ 2850Mhz, 1.425v 2-3-5-2 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now