Angry_Games Posted February 13, 2006 Posted February 13, 2006 DFI LANPARTY NF3 Ultra-D (939 AGP) 8/15/2005 BIOS AMD Athlon64 X2 4400+ dual-core (Toledo) 2x1024MB Corsair PC3500LL PRO (LED's) ATI Radeon X800 Pro 256MB AGP, Omega Catalyst 6.2 drivers, 540/502 Western Digital Caviar SE WD1600JB 160GB 7200 RPM 8M Cache IDE Ultra ATA100 NEC 3550A DVD-RW Skyhawk 520w 24-pin ATX power supply ($39.99 @ newegg!!!!) * * * * [b]Genie BIOS Settings:[/b] [color=red] CPU Overclock In Mhz............................ 216 Hammer FID Control.............................. x 11 AGP Overclock In Mhz............................ 67 LDT/FSB Frequency Ratio......................... 4x CPU VID Control................................. 1.400v Chip Set Voltage Control........................ 1.65v Memory Voltage Control.......................... 2.6v AGP Voltage Control............................. 1.5v[/color] [b]DRAM Configuration Settings:[/b] [color=red] Max Memclock (Mhz).............................. 200Mhz 1T/2T Memory Timing............................. 1T CAS# latency (Tcl).............................. 3 RAS# to CAS# delay (Trcd)....................... 3T Min RAS# active time (Tras)..................... 8T Row Precharge Time (Trp)........................ 2T Write Recovery Time (Twr)....................... 3 bus clock RAS# to RAS# delay (Trrd)....................... 3T Row refresh timg (Trfc)......................... 24T Row Cycle Time (Trc)............................ 12T Wite-to-Read Delay (Twtr)....................... 2 bus clock Read-to-Write Delay (trwt)...................... 3T Refresh Rate (Tref)............................. 3120 Cycle Write CAS Latency (Twcl)........................ Auto Max Asynchronous Latency (Twcl)................. Auto Read Preamble................................... Auto Dynamic Counter................................. Auto DRAM Drive Strenght............................. Auto DDR Data Drive Strength......................... Auto DRAM Bank Interleaving.......................... Enabled 32-Byte Granularity............................. 4 beats ========== Prime95 + 3dMark2001SE + CPU-Z 1.28 + Everest 1.51: http://www.angrygames.com/ocdb/angry/nf3/9...gp_217x11-1.gif 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: ========== short description: 216x11 @ 2390Mhz, 1.400v 3-3-8-2 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
Praz Posted February 15, 2006 Posted February 15, 2006 UT nF4 SLI-DR Expert - 12/07/05 BIOS AMD Athlon 64 3700+ San Diego G.SKILL Extreme Series 2GB DDR 500 F1-4000USU2-2GBHZ eVGA e-GeForce 6800 GS PCI Express, 500/1270 83.40 drivers Maxtor Maxline III 7L300S0 300GB Serial ATA 1.5Gb 7200RPM Hard Drive w/16MB Buffer Liteon SOHW-1693S 16X Dual Layer DVD±RW Drive (Black) OCZ ModStream OCZ52012U ATX, BTX, SATA, P4 and EPS12V 520W Power Supply Scythe SCNJ-1000 Ninja Heatpipe CPU Cooler + Nexus 120 mm Real Silent Case Fan Black/White Zalman VF700-CU VGA Cooler [b]Genie BIOS Settings:[/b] [color=navy] FSB Bus Frequency..................... 264 LDT/FSB Frequency Ratio............... 3x CPU/FSB Frequency Ratio............... 11x PCI Express Frequency................. 100 CPU VID Startup Value................. 1.400 CPU VID Control....................... 1.350 VID Special Control................... 116.8% LDT Voltage Control................... 1.20V Chip Set Voltage Control.............. 1.52v Dram Voltage Control.................. 2.56v[/color] [b]DRAM Configuration Settings:[/b] [color=darkgreen] Dram Frequency Set (Mhz).............. 200=RAM/FSB:01/01 Command Per Clock (CPC)............... Enable CAS# latency (Tcl).................... 3.0 RAS# to CAS# delay (Trcd)............. 04 Min RAS# active time (Tras)......... . 07 Row Precharge Time (Trp).............. 04 Row Cycle Time (Trc).................. 07 Row refresh timg (Trfc)............... 13 RAS# to RAS# delay (Trrd)............. 02 Write Recovery Time (Twr)............. 02 Wite-to-Read Delay (Twtr)............. 01 Read-to-Write Delay (Trwt)............ 03 Refresh Rate (Tref)................... 3684 Cycles Write CAS Latency (Twcl)...............Auto DRAM Bank Interleaving................ Enabled DQS Skew Control...................... Increase Skew DQS Skew Value........................ 0 DRAM Drive Strength................... Level 5 DRAM Data Drive Strength.............. Level 1 Max Asynchronous Latency.............. 07.0 DRAM Response Time.....................Fastest Read Preamble Time.................... 05.0 IdleCycle Limit........................016 Dynamic Counter....................... Enable R/W Queue Bypass.......................16X Bypass Max.............................07X 32-Byte Granularity................... Disable (4 bursts) [/color] Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: short description: 264x11@ 2904Mhz, 1.350v + 116.8% 3-4-4-7 @ 2.56v vdimm Share this post Link to post Share on other sites More sharing options...
Abudoggie Posted February 15, 2006 Posted February 15, 2006 DFI LANPARTY UT nF4 SLI-DR Expert - 12/7/05 BIOS Opteron 165 CCBWE 0550 UPMW OCZ Gold PC4000 2x1024MB OCZ5002048ELGE-K eVGA Geforce N545 7800GTX 512MB, 81.98 whql driver 2x WD Raptor 74gb SATA (Raid 0) Plextor Black DVD Burner Model PX-716AL/SW OCZ PowerStream OCZ520ADJSLI 520W Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 278 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.400v CPU VID Special Control - Above VID * 1.024% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.52v DRAM Voltage Control - 1.66v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 03 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31: http://home.comcast.net/~dmorisoli/Pics/pi...278_2_13_06.jpg 3dMark2003: 3dMark2005: Aquamark 3d: Everest 2.20: http://home.comcast.net/~dmorisoli/Pics/Ev...2_13_06_278.jpg ========== short description: 278x9 @ 2500Mhz, 1.400v + 102% 3-4-8-3 @ 1.66v vdimm Share this post Link to post Share on other sites More sharing options...
d3M0n Posted February 15, 2006 Posted February 15, 2006 DFI LANPARTY UT nF4 SLI-DR Expert Socket 939 NVIDIA nForce4 SLI ATX AMD Motherboard - 12/07/05 BIOS AMD Athlon64 x2 4400+ Toledo CCBWE 0531TPMW 2x1Gb G. Skill HZ eVGA 7800GTX 256MB KO edition, 510 + 60/1320 (OC runs, customized bios) 81.98 drivers Western Digital 320Gb HD (WDC WD3200JB-00KFA0) Western Digital 36Gb Raptor HD (WDC WD 360GD-00FLA2) Maxtor 120GB HD (6Y120M0) PLEXTOR Black 16X DVD+R 8X DVD+RW 8X DVD+R DL 16X DVD-R 4X DVD-RW 16X DVD-ROM 48X CD-R 32X CD-RW 48X CD-ROM 2M Cache IDE DVD burner OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ratio - x4 CPU/FSB Frequency Ratio - x10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 114.4% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.72v DRAM Voltage Control - 2.84v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3072 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Increase DQS Skew Value - 255 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 32 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29: 3dMark2003: 3dMark2005: 3dMark2006: Everest 2.20: ========== short description: 270x10 @ 2700Mhz, 1.400v * 114.4% = 1.6016v 3.0-4-4-8 @ 2.84v vdimm Share this post Link to post Share on other sites More sharing options...
wevsspot Posted February 17, 2006 Posted February 17, 2006 DFI LANPARTY nF4 Ultra-D (623-1 BIOS) AMD Athlon64 3700+San Diego 2x1GB G.Skill PC4000 HZ's ChainTech 7800GT 256MB 435/1100 81.85 drivers WD Raptors 2X74GB RAID0 LiteOn DVD-RW SOHW-1673S/LiteOn CD-RW LTR-52327S OCZ PowerStream OCZ520ADJ ATX 520W Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 11 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.375v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 2.5 + .03v DRAM Configuration Settings: DRAM Frequency Set - 200 = RAM/FSB 1:1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 03 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 04 Bus Clocks Refresh Period (Tref) - 3684 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 6 DRAM Data Drive Strength - 1 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fastest Read Preamble Time - 6.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.20: 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 260x11 @ 2860Mhz, 1.375v + 113% 3.0-4-8-4 @ 2.58v vdimm Share this post Link to post Share on other sites More sharing options...
wevsspot Posted February 18, 2006 Posted February 18, 2006 DFI LANPARTY nF4 Ultra-D (623-1 BIOS) AMD Athlon64 3700+San Diego 2x1GB G.Skill PC4000 HZ's ChainTech 7800GT 256MB 445/1100 81.85 drivers WD Raptors 2X74GB RAID0 LiteOn DVD-RW SOHW-1673S/LiteOn CD-RW LTR-52327S OCZ PowerStream OCZ520ADJ ATX 520W Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 11 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.375v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 2.66v DRAM Configuration Settings: DRAM Frequency Set - 200 = RAM/FSB 1:1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 03 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 04 Bus Clocks Refresh Period (Tref) - 3684 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 6 DRAM Data Drive Strength - 1 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 5 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + Everest 2.20: 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 260x11 @ 2860Mhz, 1.375v + 113% 3.0-4-8-4 @ 2.66v vdimm Share this post Link to post Share on other sites More sharing options...
wevsspot Posted February 20, 2006 Posted February 20, 2006 Ok all. Here is my last and final OCDB entry for the new G.Skill PC4000 HZ's. DDR550 was a no go despite all attempts. However, I've been able to squeeze nice timings out of them at 520. DFI LANPARTY nF4 Ultra-D (623-1 BIOS) AMD Athlon64 3700+San Diego 2x1GB G.Skill PC4000 HZ's ChainTech 7800GT 256MB 445/1100 81.85 drivers WD Raptors 2X74GB RAID0 LiteOn DVD-RW SOHW-1673S/LiteOn CD-RW LTR-52327S OCZ PowerStream OCZ520ADJ ATX 520W Power Supply ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 11 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.375v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 2.66v DRAM Configuration Settings: DRAM Frequency Set - 200 = RAM/FSB 1:1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 03 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3684 Cycles Write CAS Latency (Twcl) - 01 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 6 DRAM Data Drive Strength - 3 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 5 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + Everest 2.20: 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 260x11 @ 2860Mhz, 1.375v + 113% 3.0-4-8-3 @ 2.66v vdimm Share this post Link to post Share on other sites More sharing options...
digitalphoto.se Posted February 21, 2006 Posted February 21, 2006 DFI LANPARTY nF4 Ultra-D - 7/04-2 BigToe BIOS AMD OPTERON 170 0550 2x512MB TWINMOS TWISTER PRO (SAMSUNG TCCD) CLUN 3D RADEON X850XT 256MB ZALMAN VF700 2X MAXTOR MAXLINE III 250GB SATA II (16MB cache) NEC 3520 DVD-R/RW TAGAN EASYCON TG-580 U15 THERMALRIGHT SI-120 WITH PAPST 4412 F/2GL * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 255 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 101Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.325v CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - 01 DRAM Bank Interleave - Enabled DQS Skew Control - Enable DQS Skew Value - 255 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.digitalphoto.se/images/bench/du...st_3dmark01.JPG 3dMark2003: 3dMark2005: ========== short description: 255x10 @ 2550Mhz, 1.325v + 104% 2.5-3-6-3 @ 2.7v vdimm Share this post Link to post Share on other sites More sharing options...
Jdogg Posted February 23, 2006 Posted February 23, 2006 DFI LANPARTY nF4 Ultra-D - 704-2BTA AMD Opteron 148 2x1024MB G.SKILL Extreme Series DDR500 XFX 7800GT 256MB, 520/1190 81.98 drivers (2) Hitachi Deskstar 80gb ASUS Silver 16X DVD+R 8X DVD+RW OCZ Modstream 520w * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 264 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - Auto CPU VID Special Control - ABOVE VID * 104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.6v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/1 Command Per Clock (CPC) - Auto CAS Latency Control (Tcl) - Auto Min RAS# active time (Tras) - Auto Row precharge time (Trp) - Auto Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 24 Bus Clocks Wrte recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://img63.imageshack.us/my.php?image=3dmark014jl.jpg 3dMark2003: http://img159.imageshack.us/my.php?image=3dmark031tl.jpg 3dMark2005: http://img141.imageshack.us/my.php?image=3dmark051rb.jpg ========== short description: 264x11 @ 2904Mhz, 1.35v + 104% 3 4-4-8 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
ooztuncer Posted February 25, 2006 Posted February 25, 2006 DFI LANPARTY nF4 Ultra-D (704-2BTA BIOS) Opteron 146 - CABYE 0540 FPMW / SI-120 + Delta 120mm (130cfm) 2x1GB G.Skill PC4000 HZ's Evga 7800GT 256MB (485/1,120 - 83.90 drivers) SB Audigy2 WD Cavier 160GB ide LiteOn SOHC-5232K X-Clio 450W ========== Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.35v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 200 = RAM/FSB 1:1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 03 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - 01 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 5.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== ========== short description: 290x10 = 2900Mhz (9:10 divider) 1.35v x 1.10 = 1.485 vcore 3-4-4-8 @ 2.60 vdimm Share this post Link to post Share on other sites More sharing options...
Asmodeo Posted February 26, 2006 Posted February 26, 2006 UT nF4 SLI-DR Expert - 12/07/05 BIOS AMD Athlon 64 3700+ San Diego 2x512MB G.Skill F1-4800DSU2-1GBFF PC4800 Sapphire Radeon X800 GTO² 256mb PCI-E x16 @X850 (500Mhz/600Mhz) - Omega Driver 3.8.205 2x Hitachi Deskstar t7k250 200gb SATA-II (NVIDIA RAID-0) PLEXTOR DVDR PX-750A LG DVD-ROM GDR8163B OCZ PowerStream 600 DigitalDoc 5+ Fully Water Cooled by OCLABs MonoBlock Series * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 285 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.425v CPU VID Special Control - Above VID * 112% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.52v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + SmartGuardian: SmartGuardian CPU Temp is not accurate at all. The DigitalDoc 5+ sensor Temp is 27C 3dMark2003: 3dMark2005: 3dMark2006: Everest Ultimate Edition: ========== Short Description: 285x10 @ 2850Mhz, 1.425v + 112% 2.5-4-5-3 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
vrodforums Posted February 27, 2006 Posted February 27, 2006 Opteron 146 CABYE 0540 FPMW DFI Lanparty UT nF4 Ultra-D (bios 11/14/2005) Opteron 146 10x290 2.9 @ 1.525 2x512 1GB Patriot PC4800 Nvidia 7800GT Evga 470x1100 4x100GB SATA Maxtor 8mb cache raid 0 Antec Truepower 500w Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.525v CPU VID Special Control - Auto LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 16 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + Everest 2.20: 3dMark2003: 3dMark2005: ========== short description: My daughters machine, or was I gave her my FX-57 machine About average week 0540 chip I have a CAb2e 148 that is almost identical in performance DFI Lanparty UT nF4 Ultra-D (bios 11/14/2005) Opteron 146 10x290 2.9 @ 1.525 2x512 1GB Patriot PC4800 Nvidia 7800GT Evga 470x1100 4x100GB SATA Maxtor 8mb cache raid 0 Antec Truepower 500w Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now