Angry_Games Posted April 24, 2005 Posted April 24, 2005 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 3/16/2005 BIOS (Oskar Wu Alpha BIOS) AMD Athlon 64 3500+ ClawHammer/Hammer Socket 939 Processor Model ADA3500ASBOX - CAAZC 0440 stepping 2x256MB Buffalo PC3700 BH-5 - (DD466-S256/WB . . . PC3700U-30330-A1) 2x CHAINTECH Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card, 76.41 beta drivers - 562/1170 2x Western Digital Raptor WD360GD 36.7GB 10,000 RPM Serial ATA150 Hard Drive (RAID-0) ASUS CD-S520/A5 Black IDE CD-ROM Drive Skyhawk GM-570PC 570w 24-pin ATX power supply Thermalright XP-90 aluminum heatpipe heatsink + Enermax 92mm adjustable fan * * http://www.angrygames.com/sli-dr_1.htm * * ========== Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - Auto PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.450v CPU VID Special Control - Avove VID * 110% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.40v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: [bimg]http://www.angrygames.com/nf4-ultra/slidr-9.jpg[/bimg] 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 250x11 @ 2750Mhz, 1.450v + 110% 2-2-8-2 @ 3.4v vdimm Quote Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted April 24, 2005 Posted April 24, 2005 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 3/16/2005 BIOS (Oskar Wu Alpha BIOS) AMD Athlon 64 4000+ San Diego Socket 939 Processor Model ADA4000DAA5BN - CABHE 0505 stepping 2x256MB Buffalo PC3700 BH-5 - (DD466-S256/WB . . . PC3700U-30330-A1) 2x CHAINTECH Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card, 76.41 beta drivers - 562/1170 2x Western Digital Raptor WD360GD 36.7GB 10,000 RPM Serial ATA150 Hard Drive (RAID-0) ASUS CD-S520/A5 Black IDE CD-ROM Drive Skyhawk GM-570PC 570w 24-pin ATX power supply Thermalright XP-90 aluminum heatpipe heatsink + Enermax 92mm adjustable fan * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - Auto PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.300v CPU VID Special Control - Above VID * 123% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.40v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.28: 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition 1.51: ========== short description: 240x12 @ 2880Mhz, 1.300v + 123% 2-2-5-2 @ 3.4v vdimm Quote Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 4, 2005 Posted May 4, 2005 BIOS VERSION = 4/27/2005-2 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 4/27-2 BIOS (Oskar Wu Alpha BIOS) AMD Athlon 64 4000+ San Diego Socket 939 Processor Model ADA4000DAA5BN - CABHE 0505 stepping OCZ Gold Series 1GB (2 x 512MB) BH-5 (OCZ4001024ELDCGE-K) 2x CHAINTECH Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card, 76.41 beta drivers - 562/1170 Western Digital Raptor WD360GD 36.7GB 10,000 RPM Serial ATA150 Hard Drive (RAID-0) ASUS CD-S520/A5 Black IDE CD-ROM Drive Skyhawk GM-570PC 570w 24-pin ATX power supply Danger Den TDX Athlon64 (754/939) copper waterblock Danger Den "Hydor" L35 AC water pump Danger Den Black Ice Xtreme 120mm radiator Danger Den polyethylene 5.25" bay resevoir Danger Den Zerex water additive (4oz. bottle) Danger Den Tygon tubing * * (BIOS pics coming soon!) * * ========== Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - Auto PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.300v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.50v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: http://www.angrygames.com/nf4-ultra/slidr_sandiego13.jpg 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition 1.51 Memory Write: Everest Home Edition 1.51 Memory Latency: Doom III - Timedemo demo1 @ 1280x1024 - High Detail (4 runs, screenshot from 2nd run for average): ========== short description: 240x12 @ 2880Mhz, 1.300v + 123% 2-2-5-2 @ 3.5v vdimm BIOS VERSION = 4/27/2005-2 Quote Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 7, 2005 Posted May 7, 2005 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 3/16/2005 BIOS (Oskar Wu Alpha BIOS) AMD Athlon 64 3500+ Winchester Socket 939 Processor Model ADA3500DIK4BI - LBBID 0509 CPMW stepping 2x512MB OCZ Gold Edition 4000VX - (PN: OCZ5001024ELDCGEVX-K) Nvidia 6800GT PCI-E engineering sample, 76.41 beta drivers - 401/1100 2x Western Digital Raptor WD360GD 36.7GB 10,000 RPM Serial ATA150 Hard Drive (RAID-0) ASUS CD-S520/A5 Black IDE CD-ROM Drive OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail Thermalright XP-90 aluminum heatpipe heatsink + Enermax 92mm adjustable fan * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - Auto PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.300v CPU VID Special Control - Above VID * 126% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.30v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 2 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.28 + Everest 1.51: [bimg]http://www.angrygames.com/pics/sincity/sincityjet3.jpg[/bimg] 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition 1.51 Memory Write: Everest Home Edition 1.51 Memory Latency: ========== short description: 240x11 @ 2640Mhz, 1.300v + 126% 2-2-6-2 @ 3.3v vdimm BIOS VERSION = 4/14/2005-2 * * Special thanks to SinCityJet as this is his rig that he sent me to take a look at and allowed me to use it to add another entry into this overclocking database! Thanks Paul! Quote Share this post Link to post Share on other sites More sharing options...
dspayre Posted May 8, 2005 Posted May 8, 2005 DFI LANPARTY nF4 Ultra-D - 3/10/2005 BIOS AMD Athlon 64 3200+ Winchester Socket 939 Model ADA3200DIK3BI - CBBID 0506 2x512MB Corsair Value Select VS512MB400 (DDR PC3200 512MB) Leadtek WinFast PX6600 GT TDH Extreme Vesion Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card, 71.89 drivers - 550/1100 Maxtor DiamondMax 10 250GB SATA150 HDD 7,200RPM 16MB Cache NEC ND-3520A DVD±R DL IDE DVD Drive Antec NeoPower 480W ATX12V v2.0 24pin power supply Stock Heatsink Fan on CPU and Video Card + Artic Silver Ceramique Thermal Compound + 2x Ainex Aluminum Blue RAM Heat Spreaders ========== Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.450v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.50v Chip Set Voltage Control - 1.80v DRAM Voltage Control - 3.00v DRAM Configuration Settings: DRAM Frequency Set - 180 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - Auto Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - Auto Write recovery time (Twr) - Auto Write to Read delay (Twtr) - Auto Read to Write delay (Trwt) - Auto Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.28 + Everest Home Edition Version 2.00.316 Beta: http://www.angrygames.com/ocdb/BruceOC/BruceOC_pic1.JPG 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition Version 2.00.316 Beta: ========== short description: 250x10 @ 2500Mhz, 1.450v + 110% 2.5-3-7-3 @ 3.0v vdimm BIOS Version = 03/10/2005 Quote Share this post Link to post Share on other sites More sharing options...
seamuso Posted May 12, 2005 Posted May 12, 2005 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 3/10/2005 BIOS AMD Athlon 64 3200+ Winchester Socket 939 Processor Model ADA3200BIBOX - CBBID 0504 stepping 2x512MB Corsair XMS CMX512 PC3200LLv1.2 CH-5 XFX Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card, 71.89 drivers - 500/1000 3x Western Digital Caviar SE WD800JB 80GB 7200 RPM 8MB Cache IDE Ultra ATA100 Hard Drive NEC Black IDE DVD Burner SeaSonic S12-600 ATX12V 600W Power Supply 100 - 240V ZALMAN CNPS7700-CU 120mm 2 Ball Cooling Fan + 2x generic 80mm case fans MadDog Multimedia Cmedia 5.1 sound (for linux sound compatability) * * http://info.bluefrogcs.com/images/screenshots/cleaner2.jpg * * ========== Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ratio - 4x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 101Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.425v CPU VID Special Control - Avove VID * 110% LDT Voltage Control - 1.50v Chip Set Voltage Control - 1.80v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 180 (DRAM/FSB:9/10) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 05 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 05 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 5 DRAM Bank Interleave - Enabled DQS Skew Control - Increase DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - 7 Read Preamble Time - 5 IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.28.6 + Everest 1.51 + ITE SG: http://info.bluefrogcs.com/images/screenshots/screen.jpg size 845x676 3dMark2003: 3dMark2005: Aquamark 3d: Everest Write: Everest Latency: ========== short description: 250x10 @ 2500Mhz, 1.425v + 110% 2-3-6-2 @ 2.9v vdimm Quote Share this post Link to post Share on other sites More sharing options...
racinjimy Posted May 16, 2005 Posted May 16, 2005 DFI LANPARTY nF4 SLI-DR NF4 SLI-DR - 331-2 BIOS AMD Athlon 64 3500+ Winchester Socket 939 Processor Model ADA3500DIK4BI - CBBID (went from zero to hero) :nod: OCZ Voltage eXtreme EL DDR PC-3200 1GB (512MB X 2) Dual Channel Gold VX kit OCZ4001024ELDCGEVX-K MSI NX6600GT-TD128E Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card - Retail (600/1200 overclock) 2x Western Digital Raptor WD740GD 74GB 10,000 RPM Serial ATA150 Hard Drive (RAID-0) SAMSUNG 160GB SATA SP1614C PLEXTOR SATA DVD Burner 16X DVD+R 8X DVD+RW 4X DVD+R DL 16X DVD-R 4X DVD-RW 16X DVD-ROM 48X CD-R 24X CD-RW 48X CD-ROM 8M Cache - Retail PX-716SA/SW SEASONIC S12 600 Watt ATX 12V Power Supply 24 PIN custom water-cooled setup: Laing D4/TC 120.2/Dtek WW CPU block/PolarFlo TT GPU block ========== Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ratio - 4 CPU/FSB Frequency Ratio - 11 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.45 CPU VID Control - 1.400v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.20v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 2560 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Auto Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.28.2 + Everest 1.51: http://i6.photobucket.com/albums/y203/raci...rimeeverest.jpg 3dMark2003: 3dMark2005: Aquamark 3d: short description: 240x11 @ 2640Mhz, 1.400v + 123% 2-2-6-2 @ 3.2v vdimm Quote Share this post Link to post Share on other sites More sharing options...
Geebs Posted May 19, 2005 Posted May 19, 2005 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 510-2 BIOS (Oskar Wu Alpha BIOS) AMD Athlon 64 FX-55 ClawHammer/Hammer Socket 939 Processor Model AMD FX55 ADAFX55 OEM CAA2C 0438TPMW stepping 2x 512MB OCZ PC3200 Platinum Rev. 2 (Orange) OCZ4001024ELDCPER2-K 2x Asus EN6800 Ultra 2DT 256 SLI, 76.50 beta drivers - 530/1120 2x Western Digital Raptor WD740GD 74GB 10,000 RPM Serial ATA150 Hard Drive (RAID-0) Plextor PX-W 4012A - Samsung SD-616E (IDE 1) OCZ Powerstream 600 OCZ600ADJ EU - 600W Swiftech MCX 6400-V Copper/Aluminum A64 Heatsink * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 280 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.30v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.50v Chip Set Voltage Control - 1.80v DRAM Voltage Control - 3.0v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 04 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 0780 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Decrease DQS Skew Value - 0 DRAM Drive Strength - Level 5 DRAM Data Drive Strength - Level 1 Max Async Latency - 8ns DRAM Response Time - Fast Read Preamble Time - 5ns IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: http://www.angrygames.com/ocdb/Geebs/10x28...CPU-Z_3DM01.JPG 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition: ========== short description: 280x10 @ 2800Mhz, 1.300v + 123% 2.5-4-6-3@ 3.0v vdimm Quote Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 19, 2005 Posted May 19, 2005 DFI LANPARTY nF4 SLI-DR NF44 SLI-DR - 5/10/2005-2 BIOS AMD Athlon 64 X2 4400+ Dual Core Socket 939 Processor Model 2x512MB OCZ Gold Edition 4000VX - (PN: OCZ5001024ELDCGEVX-K) Nvidia 6800GT PCI-E engineering sample, 76.41 beta drivers - 401/1100 3x HITACHI Deskstar 7K80 HDS728080PLA380 -0A30356 80GB 7200 RPM Serial ATA II Hard Drive - OEM (RAID-0) ASUS CD-S520/A5 Black IDE CD-ROM Drive OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail Thermalright XP-90 aluminum heatpipe heatsink + Enermax 92mm adjustable fan * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - Auto PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.250v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.40v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.28 + Everest 1.51: http://www.angrygames.com/ocdb/angry/x2_2640/x2_2640-1.jpg 3dMark2003: 3dMark2005: Aquamark 3d: AMD Nbench: ========== short description: 240x11 @ 2640Mhz, 1.250v + 113% 2-2-5-2 @ 3.4v vdimm BIOS VERSION = 5/10/2005-2 * * Previous 230x11 OCDB Entry screens here: http://www.angrygames.com/ocdb/angry/x2_2533/ Quote Share this post Link to post Share on other sites More sharing options...
Guest Kronos Posted May 20, 2005 Posted May 20, 2005 Short description: 250x11 @ 2750Mhz, 1.300v + 123% 2-2-6-2 @ 3.3v vdimm BIOS 5-10-3 DFI LANPARTY UT nF4 Ultra-D AMD Athlon 64 3700+ San Diego Integrated into Chip FSB Socket 939 Processor Model ADA3700BNBOX eVGA 256-P2-N376-AX Geforce 6800GT 256MB GDDR3 PCI-Express x16 ENERMAX Noisetaker EG495P-VE SFMA ATX 485W OCZ 1GB (2 x 512MB) 184-Pin DDR SDRAM DDR 500 (PC 4000) Unbuffered Dual Channel Kit System Memory Model OCZ5001024ELDCGEVX-K THERMALTAKE Tsunami VA3000BWA Black Aluminum ATX Mid Tower Computer Case ZALMAN CNPS7000B-Cu LED 2 Ball Blue LED Light Cooling Fan -===========================- Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - X 11.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.300v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.30v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) -===========================- Prime95 + 3dMark2001SE + CPU-Z 1.27: http://img227.echo.cx/my.php?image=pic12nc.jpg 3dMark2003: 3dMark2005: Aquamark 3d: Everest 1.51: http://img281.echo.cx/my.php?image=pic53gb.jpg -===========================- Quote Share this post Link to post Share on other sites More sharing options...
oc newbie Posted May 28, 2005 Posted May 28, 2005 DFI LANPARTY nF4 ultrad - 4/14-2 BIOS (Oskar Wu beta BIOS) AMD Athlon 64 3200+ winchester Socket 939 Processor Model ADA3200BIBOX CBBID 0505 BPHW msi Geforce 6600 256MB PCI-Express x16 Video Card, 71.89 drivers - 412/615 ocz value vx 2x512mb lite on dvd/rw 8x ocz modstream 520 watt 24-pin ATX power supply western digital cavier se ide hard drive * * ========== Genie BIOS Settings: FSB Bus Frequency - 275 LDT/FSB Frequency Ration - 3 CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.5v CPU VID Control - 1.350v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.40v DRAM Configuration Settings: DRAM Frequency Set - 180 (DRAM/FSB:9/10) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 0648 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - 8ns Read Preamble Time - 6ns IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: http://img77.echo.cx/my.php?image=screen023gb.jpg 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 275x9 @ 2475Mhz, 1.350v + 123% 2-2-5-2 @ 3.4v vdimm Quote Share this post Link to post Share on other sites More sharing options...
THunDA Posted June 6, 2005 Posted June 6, 2005 DFI nF4 DAGF - 05/27/2005 BETA BIOS 4000 Sandy 0515 SPMW 2x512mb OCZ pc3200EL Rev2 tcc5 Power Color x850xt @ 570600 with Cat 5.5 1x 120gig Maxtor sata hard drive ASUS IDE CD-ROM Drive OCZ 600w Power Stream PSU Thermalright SLK948U with 92mm Tornado * * * * ========== Genie BIOS Settings: CPU Frequency - 255 Hammer Fid Control - 11 HTT Frequency - 4 PCIE Clock - 100Mhz DDR Voltage Control - 3.1v Chip Voltage Control - 1.6v Over Voltage on the fly - Disabled Fixed CPU Voltage - 1.55v DRAM Configuration Settings: Mem Clock mode - Limit Mem Clock Index Value - 200 (DRAM/FSB:1/01) CAS Latency Control (Tcl) - 2.5 Min RAS# active time (Tras) - 08 Bus Clocks RAS# to CAS# delay (Trcd) - 03 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DDR Output Driving - Auto DDR DQ Drive Strenth - Auto Bottom of 32Bit[31:24]IO - B0 1T2T Memory Timing - 1T Read Preamble Value - 5ns Async Latency Value - 7ns Dynamic IdleCycle Counter - 256 DRAM Bank Interleave - Enable Burst Length - 4 beats Enable ALL DIMM Clock - enable SW Memory hole remapping - disable HW Memory hole remapping - disable MTRR Mapping mode - continuous DRAM ECC Feature Control - disable ========== Prime95 + 3dMark2001SE + CPU-Z 1.28: ( Not sure why it says 1.4vcore.. it IS 1.55v in bios.. ) 3dMark2003 + Everest 1.51: 3dMark2005 + Everest 1.51: Aquamark 3d: ========== short description: 255x11=2800mhz 1.55vcore 3.1vdimm Quote Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.