Snowpro Posted April 17, 2006 Posted April 17, 2006 146 Opteron @ 276x10, 1.400v + 104% 3-4-4-8 @ 2.5v _________________________________________________ DFI LANPARTY UT nF4 Ultra-D - 704-2 BigToe BIOS AMD Opteron 146 Venus 1MB L2 (CACJE 0607 APBW) G.SKILL Extreme Series HZ 2x1GB PC 4000 DDR (Samsung UCCC) XFX 6800 XTreme 256MB, 425/1200 81.98 drivers Seagate Barracuda 7200.9 ST3808110AS 80GB 7200 RPM 8MB Cache SATA 3.0Gb/s NEC 16X DVD±R DVD Burner Black IDE Model ND-3550A OCZ PowerStream OCZ520ADJSLI ATX, BTX, EPS12V 520W Power Supply AMD Athlon 64 Stock 4 Copper Heatpipe Heatsink + 80x20mm Delta fan ========== Genie BIOS Settings: FSB Bus Frequency - 276 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.50v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 04 Bus Clocks Refresh Period (Tref) - 3684 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 255 DRAM Drive Strength - Auto DRAM Data Drive Strength - Level 3 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 7 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.33: http://i53.photobucket.com/albums/g51/snowpro1/a564965c.jpg 3dMark2003 + Super PI/Mod1.5 XS: http://i53.photobucket.com/albums/g51/snowpro1/3aca8895.jpg 3dMark2005: http://i53.photobucket.com/albums/g51/snowpro1/60392f07.jpg A64 Tweaker V0.60 beta: http://i53.photobucket.com/albums/g51/snowpro1/26fc1082.jpg Everest read v2.00: http://i53.photobucket.com/albums/g51/snowpro1/072fab52.jpg ========== short description: 276x10 @ 2760Mhz, 1.400v + 104% 3-4-4-8 @ 2.5v vdimm Share this post Link to post Share on other sites More sharing options...
Devon Posted April 20, 2006 Posted April 20, 2006 DFI Lanpart UT SLI-D (2005/11/14 NF4LDB14) Amd athlon 64 X2 3800+ Toledo (oc'd @ 2700mhz) Coolermaster AQUAGATE Mini R80 watercooling Own custom cooling design on PWMIC heatsinks 2X 1gig OCZ GX XTC gold PC4000 (3,4,3,7 1T timing) Sapphire X1900XT (Flashed BIOS to XTX and OC'D to 680/1580) catalyst 6.4 drivers 250GB maxtor SATA 16MB cache (Maxtor 6L250S0) 80GB maxtor ATA 8MB cache (Maxtor 6Y080P0) IEEE 1394 cd/dvd external enclosure with NEC DVD-Writer hiper Type R 580W PSU ============================================================ Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ration - X4.0 CPU/FSB Frequency Ratio - X10.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.500v CPU VID Special Control - Auto LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.60v DRAM Configuration Settings: DRAM Frequency Set - 180 (DRAM/FSB:9/10) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ============================================================ Prime95, CPU-Z and 3D Mark 2001 SE Results http://homepage.ntlworld.com/tim.goldfield...atatbase/01.jpg 3D Mark 03 Results http://homepage.ntlworld.com/tim.goldfield...atatbase/02.jpg 3D Mark 05 Results http://homepage.ntlworld.com/tim.goldfield...atatbase/03.jpg Everest, SisSoft sandra and IDLE Temps http://homepage.ntlworld.com/tim.goldfield...atatbase/04.jpg DOOM3 timedemo demo1 1280X1024 Hight Details http://homepage.ntlworld.com/tim.goldfield...atatbase/05.jpg Share this post Link to post Share on other sites More sharing options...
expresso Posted April 21, 2006 Posted April 21, 2006 did anyone test a x2 4200+ with 2 gig OCZ PC4000 Gold XTC memory - 3-4-3-8 ? i been looking over this database but cant find a similar setup with this memory - if anyone can link me to one in this database that would be great - i been testing for 3 weeks now and its driving me crazy thanks Share this post Link to post Share on other sites More sharing options...
expresso Posted April 21, 2006 Posted April 21, 2006 sorry i think i posted in the wrong place Share this post Link to post Share on other sites More sharing options...
Prostock62 Posted April 21, 2006 Posted April 21, 2006 sorry i think i posted in the wrong place You may want to post here in the overclock discussion thread insted. http://www.dfi-street.com/forum/showthread.php?t=10196 Share this post Link to post Share on other sites More sharing options...
railmeat Posted April 21, 2006 Posted April 21, 2006 hey guys, i had 1 simple question if i may?specs below btw.ayway i just been attempting and trying diff settings and finally got this 3700sandy (stepping 1,revesion sh-e4)to go to 3:4 cas 2.5 -3-2-5 ,2t, 2.7 volts,stock cpu voltage,swiftech helicoil heatsink120 78cfm zalman @ 41c idle )allllll settings are on auto except 249 fsb 2.75ghz with these 4 gigs,and 7900gtx512 scored 11,050 in 3dmark05,and cpu verified CPU-Z Database (ID : 88346).now im not to sure if this is all safe?,temps are low as can be(41 idle,52 after 3dmarkruns05-06)now is anything defintly needed to be changed htt at 249(is that fsb in cpuz?...to hi?)this overclock seems kinda hi....i cant belive i banged 1,000 more points in 3dmark05 =0 i honestly cant belive its at 2.75ghz.i was never into overclocking until my freinds were calling me a womans private part :cat: any advice will be appriacted greatly....bf2 time :0 Share this post Link to post Share on other sites More sharing options...
steelballzz Posted April 21, 2006 Posted April 21, 2006 OPTERON 146 CABNE 0530 FPMW BOX COOLED BY SCHYTE NINJA SCNJ-1000 AND NB SX2 DFI SLI -DR EXPERT "VENUS" 2X256 TWINMOS BH5 GECUBE X800 XL 256 DDR3 COOLED BY ZALMAN VF 700 AL Cu DVD-RW LG GSA 4120B HDD HITACHI 80 G IDE ATA 133 OCZ POWERSTREAM 420W AEROCOOL EXTREME ENGINE 3T Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.325v CPU VID Special Control - Above VID * 121,6% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.68v DRAM Voltage Control - 3.44v DRAM Configuration Settings: DRAM Frequency Set - 166 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 01 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 5.5 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Enable(2 Bursts) ========== ======================================================== 3dmark01 + Prime + 2x cpuz + Everest + MBM: 3dmark03 + 2x cpuz + MBM: 3dmark05 + 2x cpuz + MBM: ======================================================== Short description opty 146 300x10 1,58vcore 2x256 bh5 3,44v vdimm Share this post Link to post Share on other sites More sharing options...
ThreeFlow Posted April 26, 2006 Posted April 26, 2006 DFI LANPARTY nF4-D - 704-2bta (Modded to enable SLI and SATA II, replaced chipset fan /w Vantec Iceberq 4 AMD Opteron 146 - CAB2E 0546 GPAW, Thermalright XP-120 /w Antec 79CFM fan connected to Zalman Fanbus 1GB (2x512MB) OCZ Platinum PC3700 (TCCD 434, Brainpower PCB, Inserted in Orange slots) Sapphire X800 GTO2 256MB, (16 pipelines enabled) 573/639 6.3 catalyst drivers, Zalman VF700 connected to Zalman Fanbus Seagate 250GB 7200.8 SATA I hard drive LG GSA4167B + LG GSA4160B OCZ PowerStream OCZ520ADJ ATX 520W SLI Power Supply * * ========== Genie BIOS Settings: FSB Bus Frequency - 287 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 105Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.350v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.00v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3072 Cycles DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 (weak 4) DRAM Data Drive Strength - Level 2 Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 7.0 Nano Seconds IdleCycle Limit - 016 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.32 + Everest 2.80 Reads: 3dMark2003 + Smartguardian + Everest 2.80 Writes: 3dMark2005 + Everest 2.80 Latency: ========== short description: 287x10 @ 2870Mhz, 1.350v + 110% (1.43v) 2.0-3-8-3 @ 3.0v vdimm Share this post Link to post Share on other sites More sharing options...
Prostock62 Posted April 26, 2006 Posted April 26, 2006 DFI LANPARTY nF4 SLI-DR - 7/04-2 BigToe BIOS AMD Opteron 146 Venice CACJE 2x512MB Mushkin 3500 Lev 11 BH-5 Evga 6600Gt 128 MB, 556Mhz/ 1.11Ghz 84.21 drivers 2x Hitachi Sata 11 Raid0 hdd (8MB cache) OCZ PowerStream OCZ520ADJ ATX 600W Power Supply - Retail * * ========== Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.375v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.70v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 07 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 13 Bus Clocks Row to Row delay (Trrd) - 01 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 016 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Enabled ==========[/size http://img184.imageshack.us/my.php?image=oc10ol.jpg Short Description Opty 146 290x10 1.375 Vcore 3.7 VDimm Share this post Link to post Share on other sites More sharing options...
Praz Posted April 30, 2006 Posted April 30, 2006 LANPARTY UT NF4 SLI-DR Venus - 03/07/06 BIOS AMD Opteron 170 OCZ OCZ5002048EBPE-K 2GB Kit DDR500 PC4000 Platinum Edition eVGA e-GeForce 6800 GS PCI Express, 500/1270 83.40 drivers Hitachi Deskstar T7K250 160GB Serial ATA II 7200RPM Hard Drive w/8MB Buffer x 2 RAID 0 Maxtor Maxline III 7L300S0 300GB Serial ATA 1.5Gb 7200RPM Hard Drive w/16MB Buffer Liteon SOHW-1693S 16X Dual Layer DVD±RW Drive (Black) OCZ PowerStream OCZ520ADJSLI ATX, BTX, EPS12V 520W Power Supply Swiftech STORM Extreme Performance Universal Water-block - Rev 2 Swiftech MCP655 Pump Black Ice Pro III Triple 120mm Radiator With D12SL-12 YATE LOON 120mm Case Fans Chipset Cooled By Evercool VC-RE VGA Cooler Zalman VF700-CU VGA Cooler [b]Genie BIOS Settings:[/b] [color=navy] FSB Bus Frequency..................... 295 LDT/FSB Frequency Ratio............... 3.0x CPU/FSB Frequency Ratio............... 10x PCI Express Frequency................. 100 CPU VID Startup Value................. 1.350 CPU VID Control....................... 1.450 VID Special Control................... 107.2% LDT Voltage Control................... 1.20V Chip Set Voltage Control.............. 1.52v Dram Voltage Control.................. 2.56v[/color] [b]DRAM Configuration Settings:[/b] [color=darkgreen] Dram Frequency Set (Mhz).............. 166=RAM/FSB:05/06 Command Per Clock (CPC)............... Enable CAS# latency (Tcl).................... 3.0 RAS# to CAS# delay (Trcd)............. 03 Min RAS# active time (Tras)......... . 00 Row Precharge Time (Trp).............. 02 Row Cycle Time (Trc).................. 07 Row refresh timg (Trfc)............... 12 RAS# to RAS# delay (Trrd)............. 00 Write Recovery Time (Twr)............. 02 Wite-to-Read Delay (Twtr)............. 01 Read-to-Write Delay (Trwt)............ 02 Refresh Rate (Tref)................... 3120 Cycles Write CAS Latency (Twcl)...............01 DRAM Bank Interleaving................ Enabled DQS Skew Control...................... Auto DQS Skew Value........................ 0 DRAM Drive Strength................... Level 04 DRAM Data Drive Strength.............. Level 2 Max Asynchronous Latency.............. 08.0 DRAM Response Time.....................Fastest Read Preamble Time.................... 03.0 IdleCycle Limit........................256 Dynamic Counter....................... Disable R/W Queue Bypass.......................16X Bypass Max.............................07X 32-Byte Granularity................... Disable (4 bursts) [/color] Prime95 + 3dMark2001SE + CPU-Z 1.33.1 + Everest 2.01: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: X3 Demo, Dual Super_Pi, OCCT, HD Tach short description: 295x10@ 2950Mhz, 1.450v + 107.2% 3-3-2-0 @ 2.56v vdimm Share this post Link to post Share on other sites More sharing options...
Voltes-5 Posted May 3, 2006 Posted May 3, 2006 DFI LANPARTY Expert Tony's 406 BIOS AMD Opteron 165 CCBWE 0551VPMW naked 4 X 1GB Crucial Ballistix Z503 XFX 7900GT 256MB, 520/1500 8456-X64 drivers Maxtor DiamondMax 10 Model 65250SO 250GB SATA Lite On SOHW-1633S PC P&C 510 ASL Danger Den Water Pump TDX CPU block MCW60 GPU block Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - X 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.450v CPU VID Special Control - Above VID * 112% LDT Voltage Control - 1.50v Chip Set Voltage Control - 1.84v DRAM Voltage Control - 2.80v[/color] DRAM Configuration Settings: [color=red] DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 10 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Odd Divisor Correct - Enable DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.33 http://img136.imageshack.us/img136/4836/4gbx64custom2hb.png 3dMark2003: http://img99.imageshack.us/img99/9983/03custom1gq.png 3dMark2005: http://img141.imageshack.us/img141/3549/05custom0lb.png Everest Memory Read http://img151.imageshack.us/img151/4228/x6...adcustom6ic.png ========== short description: 300x9 @ 2700Mhz, 1.450v + 112% 3-4-10-4 @ 2.8v vdimm Share this post Link to post Share on other sites More sharing options...
steelballzz Posted May 4, 2006 Posted May 4, 2006 OPTERON 146 CABNE 0530 FPMW BOX COOLED BY SCHYTE NINJA SCNJ-1000 AND NB SX2 DFI SLI -DR EXPERT "VENUS" 4/06 2X512 OCZ PLATINUM LIMITED EDITION BH6 GECUBE X800 XL 256 DDR3 COOLED BY ZALMAN VF 700 AL Cu DVD-RW LG GSA 4120B WD RAPTOR 74G OCZ POWERSTREAM 420W AEROCOOL EXTREME ENGINE 3T Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.275v CPU VID Special Control - Above VID * 124,0% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.68v DRAM Voltage Control - 3.44v DRAM Configuration Settings: DRAM Frequency Set - 166 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - AUTO DRAM Response Time - Normal Read Preamble Time - AUTO IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Enable(2 Bursts) ========== ==========================«»============================== SHORT DESCRIPTION 300X10 1,54V 250 2-2-2-5 3,45VDIMM Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now