DangerIsGo Posted March 2, 2006 Posted March 2, 2006 I just tried the modded ini file w/ MBM5 and this is what I got: Somethings wrong Share this post Link to post Share on other sites More sharing options...
soundx98 Posted March 3, 2006 Posted March 3, 2006 @Supershanks - even a solid piece of wire has some resistance. while there should be no difference I'd use the points shown. The AUX connector has 3.3v and ground. not ALL SATA connectors do. @Alienwhere- yes it works with the Expert. But many believe that some boards report temps 8-10 degrees low. DFI Taiwan is looking at it. @DangerIsGo - yes something is wrong if you are talking about file I posted in thread. Did you use the Configuration Wizzard? That is a no-no. When you copied the Data file did it ask you if you wanted to overwrite? It should have. Share this post Link to post Share on other sites More sharing options...
supershanks Posted March 3, 2006 Posted March 3, 2006 soundx98, Thanks again for your help. My unit doesn't have the aux connecter but does have the full sata set. Edit: Idle Load Only values (don't count Chipset & LDT Volts) a bit adrift to multim are on load 12v = 12.13 & vcore at 1.41v but can live with that cheers Mord & soundx98 Share this post Link to post Share on other sites More sharing options...
Mord Posted March 3, 2006 Posted March 3, 2006 @Supershanks Happy to see you busy, my friend. soundx98 is right about the ground point. @soundx98 I've sent you the info. But, how the hell do you add the ACPI sensor in MBM5?! PS: Got my RMA'd 6800GT :cool: . Time to change my sig . Best regards, Abyss Share this post Link to post Share on other sites More sharing options...
soundx98 Posted March 3, 2006 Posted March 3, 2006 Thank you for the reply Mord. I'll be in contact. Good Luck at the Overclocking and Modding challenge. I'm sure you'll kickazz. Share this post Link to post Share on other sites More sharing options...
supershanks Posted March 3, 2006 Posted March 3, 2006 Interesting results on vdimm:- Bios - MM 2.9 = 2.97 2.8+ = 2.92 2.8 = 2.88 2.7+ = 2.81 tested earlier with ground probe in molex. having both your replies i re-measured using mobo points after swapping fans out Another reason for using single Probe Results were the same. So my Vdimm is roughly .07 above bios, i expected a bit from what i've read but not quiet that much. Share this post Link to post Share on other sites More sharing options...
fst h2o Posted March 3, 2006 Posted March 3, 2006 I'm sorry if this has been covered already, but is there a different data file for the Expert board? Or do I just use the NF4 file? Share this post Link to post Share on other sites More sharing options...
soundx98 Posted March 4, 2006 Posted March 4, 2006 I'm sorry if this has been covered already, but is there a different data file for the Expert board? Or do I just use the NF4 file? hehehe, yes it's been covered. 5 posts above you Use the same file on the Expert board. Share this post Link to post Share on other sites More sharing options...
fst h2o Posted March 4, 2006 Posted March 4, 2006 hehehe, yes it's been covered. 5 posts above you Use the same file on the Expert board. Well, I guess I should have looked a little closer at the last page. Thanks. Share this post Link to post Share on other sites More sharing options...
soundx98 Posted March 4, 2006 Posted March 4, 2006 I changed the 1st Post in thread to make it clear. Enjoy Share this post Link to post Share on other sites More sharing options...
SaFrOuT Posted March 4, 2006 Posted March 4, 2006 just wanted to report that i finally got my evga 7800GT and using mbm5 with the nvidia plugin is working fine only my vga doesn't have amb. temp sensor Share this post Link to post Share on other sites More sharing options...
joek71 Posted March 4, 2006 Posted March 4, 2006 Yes for some reason the 7800 does not come with that sensor, my 6800 Ultra does. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now