sswilson Posted October 12, 2006 Posted October 12, 2006 DFI LANPARTY UT nF4 ULTRA-D (704-2BTA BIOS) AMD64 SAN DIEGO 3700+ KAB2E 0602GPEW Thermaltake Bigwater 745 WC kit 2 X 1024 OCZ PC4000 (OCZ5002048ELGEGXT-K) BFG GeForce 6600GT, 525/1050 9.931 drivers Samsung SP1203N 120GB 7200RPM ATA hdd AOpen DUW1616 16X DVD +/-R, 4X Dual Layer OCZ MODSTREAM 520w Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 305 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - X 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.475v CPU VID Control............................... - 1.475v CPU VID Special Control....................... - Above VID * 113% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 3.10v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=dRAM/FSB: 05/06 Command Per Clock (CPC)....................... - Auto CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 3.0 Min RAS# active time (Tras)................... - 07 Row precharge time (Trp)...................... - 02 Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 17 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 08.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 07.0 Nano Seconds IdleCycle Limit............................... - 008 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003 + Everest Mem Read: 3dMark2005 + Everest Mem Latency: 3dMark 2006 + Mem Write: Aquamark: ========== short description: 305x10 @ 3050Mhz, 1.650v cpu 3-3-2-7 @ 3.10v vdimm 29 idle 44 load Share this post Link to post Share on other sites More sharing options...
delemon Posted October 12, 2006 Posted October 12, 2006 DFI LANPARTY nF4 SLI-DR (4/06BTA BIOS) AMD Opteron 165 CCBBE 0615DPMW 2x512MB Kingston HyperX PC3200 KHX3200K2/1G (BH-5) XFX 7800GTX 256MB, 91.47 drivers, stock clock/mem 2x Hitachi 160GB SATA hdd (8MB cache) Lite-On SOHW-1213S OCZ PowerStream OCZ520ADJSLI ATX 520W Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 320 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.45V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.5v DRAM Voltage Control.......................... - 3.2v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2 RAS# to CAS# delay (Trcd)..................... - 2 Min RAS# active time (Tras)................... - 6 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 13 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: http://www.weaveroffates.com/images/ocimages/DC-opty-320.jpg 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark 3: http://www.weaveroffates.com/images/ocimages/aqua-dc.jpg ========== short description: 320x11 @ 2880Mhz, Vcore 1.5v 2-2-6-2 @ 3.20v vdimm Share this post Link to post Share on other sites More sharing options...
faheyd Posted October 15, 2006 Posted October 15, 2006 NOTE: OLD, I've got a 8800GTS that I've not done the tests on. Feb 07...I've got some new mem, watercooled now, Dec 06. DFI LANPARTY NF4 Ultra-D (939 PCI-E SLI) 04/06/20006 BIOS AMD Athlon64 X2 4800+ dual-core (Toledo) Crucial Ballistix BL2KIT12864Z503.16TD1 (1GB x 2)PC4000(DDR500) NVidia XFX 7900GTX 512MB Bios 5.71.22.12.15 , Forceware 91.47 drivers Seagates, 3 each, 300GB SATA I & II, 8MB Cache, Non-Raid NEC AD-7170A DVD-RW, firmware 1.O3 (This drive works well after installing nero 7.7.5.1, no more coasters!) OCZ GameXStream 700W power supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 281 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - STARTUP CPU VID Control............................... - 1.30v CPU VID Special Control....................... - +123% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 04 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles Odd Divisor................................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Off DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Weak DRAM Data Drive Strength...................... - Level 4 Max Async Latency............................. - 6 DRAM Response Time............................ - Fast Read Preamble Time............................ - 5 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE (35238) + CPU-Z + Everest 2.20: 3dMark2003 (22948): 3dMark2005 (11073): 3dMark2006 (6159): AquaMark (113677): ========== short description: 281x10 @ 2812MHz, 1.55v (Default) 3-4-8-4 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
bleach Posted October 16, 2006 Posted October 16, 2006 DFI LANPARTY nF4 SLI-DR EXPERT(04/06-Official) AMD Opteron 144 CAB1E 0604 2x512MB Patriot PC4800 (TCCD) Evga GeForce 7900GT KO, 580/1760 91.33 drivers 250GB Seagate 7200.9 SATA hdd SAMSUNG CDVD/RW Combo Drive Silverstone 600watt Modular PSU Thermalright XP-90 + Vantec Tornado 92mm * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - 9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.40v CPU VID Special Control....................... - +107% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.54v DRAM Voltage Control.......................... - 2.92v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Disable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 7 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 15 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: http://i14.photobucket.com/albums/a306/nmt...0pics/1st-1.jpg 3dMark2003: http://i14.photobucket.com/albums/a306/nmt...3d03-2small.jpg 3dMark2005: http://i14.photobucket.com/albums/a306/nmt...3d05small-2.jpg 3dMark 2006: http://i14.photobucket.com/albums/a306/nmt...s/3d06small.jpg ========== short description: 334x9 @ 3006Mhz, 1.46v vcore 3-4-7-3 @ DDR668, 1.92v vdimm Share this post Link to post Share on other sites More sharing options...
Robc1880 Posted October 18, 2006 Posted October 18, 2006 DFI LANPARTY nF4 SLI-DR Venus (BIOS official 4/6/06) Opteron 165 CCBBE 0615DPMW 2x1024MB OCZ PC4000EB (OCZ5001024EBPE-K) EVGA 7900GTO, stock 91.47 drivers 2 x 74GB Raptor RAID 0 2 x 320GB Seagate 7200.10 RAID 1 NEC 3540A DVD+/-RW OCZ GameXstream 700W * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 315 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.400v CPU VID Control............................... - 1.4 CPU VID Special Control....................... - 104.8% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3T RAS# to CAS# delay (Trcd)..................... - 3T Min RAS# active time (Tras)................... - 8T Row precharge time (Trp)...................... - 2T Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 08 DRAM Data Drive Strength...................... - Level 2 (reduce 30%) Max Async Latency............................. - 8ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6ns IdleCycle Limit............................... - 64 Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark 3: ========== short description: 315 x 9 @ 2835Mhz, 1.400v + 104% 3-3-8-2 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
smolt Posted October 18, 2006 Posted October 18, 2006 DFI LANPARTY UT nF4 Ultra-D (BIOS 406) AMD 3500+ (Vince E6) BigTyphoon/ Evercool VC-RE 2x512MB GAIL ONES PC4800 TccD XFX GeForce 7600GTxxx, 590/800 84.21 drivers 80 Gig Hitachi Sata 11 hdd NEC DVD RW ND-4570A 600-Watt Sharkoon SilentStorm 120 Power Supply ========== [b]Genie BIOS Settings:[/b] [color=blue] FSB Bus Frequency............................. - 295 LDT/FSB Frequency Ratio....................... - 2.5 CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.475v CPU VID Control............................... - 1.525v CPU VID Special Control....................... - 113% LDT Voltage Control........................... - 1.5v Chip Set Voltage Control...................... - 1.80v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=blue] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 13 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - L8 DRAM Data Drive Strength...................... - L1 Max Async Latency............................. - 8.0 DRAM Response Time............................ - Normal Read Preamble Time............................ - 5.5 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z http://img171.imageshack.us/img171/7590/desk1cc4.jpg 3dMark2003: 3dMark2005: 3dMark 2006: AquaMark ========== Everest Memory read Everest Memory Write Everest Memory Latency short description: 295x10 @ 2950Mhz, 1.72 cpu voltages 3-4-8-4 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
Redbeaver Posted October 19, 2006 Posted October 19, 2006 DFI Infinity NF4 SLI AMD 64 X2 socket939 3800+ (@2870Mhz, 287x10) 2x1024MB OCZ Gold XTC PC4000 DDR500 OCZ5002048ELGEGXT-K (@DDR480) eVGA 7900GT KO Superclock N567-BX volt mod 1.5V Forceware 92.91 drivers, 675/1750 Seagate 7200.9 SATA2 2x80GB 8MB cache on RAID-0 Pioneer 8x DVD-RW DVR-107D Creative Audigy Enermax Liberty 500W ATX2.2 Power Supply Windows XP SP2 * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] CPU Frequency.................... - 287 Hammer Fid Control............... - 10 HTT Frequency.................... - x3 PCIE Clock....................... - 100Mhz DDR Voltage Control.............. - 2.8v Chip Voltage Control............. - 1.6v CPU Voltage...................... - 1.550 [/color] [b]DRAM Configuration Settings:[/b] [color=red] Mem Clock mode................... - Limit Mem Clock Index Value............ - 166 CAS Latency Control (Tcl)........ - 3 Min RAS# active time (Tras)...... - 8 RAS# to CAS# delay (Trcd)........ - 4 Row precharge time (Trp)......... - 3 Row to Row delay (Trrd).......... - 3 Row Cycle time (Trc)............. - 12 Row refresh cyc time (Trfc)...... - 16 Write recovery time (Twr)........ - 2 Write to Read delay (Twtr)....... - 3 Read to Write delay (Trwt)....... - 2 Refresh Period (Tref)............ - 3120 Write CAS Latency (Twcl)......... - Auto DDR Output Driving............... - Auto DDR DQ Drive Strenth............. - Auto Bottom of 32Bit[31:24]IO......... - B0 1T2T Memory Timing.............. - 1T Read Preamble Value.............. - 6ns Async Latency Value.............. - 8ns Dynamic IdleCycle Counter........ - 256 DRAM Bank Interleave............. - Enable HW Memory hole remapping........ - disable MTRR Mapping mode................ - Continuous DRAM ECC Feature Control......... - disable [/color] ========== Prime95 + 3dMark2001SE + 2x CPU-Z: 3dMark2003: 3dMark2005: 3dMark2006: ========== short description: 287x10=2870mhz 1.55vcore 2.9vdimm 3.0-4-3-8 Share this post Link to post Share on other sites More sharing options...
allthatwhichis Posted October 20, 2006 Posted October 20, 2006 DFI LANPARTY nF4 SLI-DR Venus 3/29 BIOS AMD Opteron 146 CAB2E 0546 2x1024MB G Skill PC4000HZs Giga-Byte GeForce 6600GT, Stock 81.89 drivers 80GB Western Digital SATA hdd Sony DL DVD-RW/RAM AeroCool Turbine 550 * * ========== [B]Genie BIOS Settings:[/B] [COLOR=red] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.50v CPU VID Special Control....................... - *109.6% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.62v DRAM Voltage Control.......................... - 2.55v[/COLOR] [B]DRAM Configuration Settings:[/B] [COLOR=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/COLOR] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 300x10 @ 3000Mhz, 1.632 cpu voltages 3-4-4-8 @ 2.55v vdimm Share this post Link to post Share on other sites More sharing options...
NLight95 Posted October 20, 2006 Posted October 20, 2006 DFI LanParty nF4 Ultra-D (04/06/06 BIOS) AMD Athlon 64 3000+ venice 2x1024MB G.Skill Extreme Series DDR500 (F1-4000USU2-2GBHZ) Sapphire X1800XT 512MB, 709/788 Catalyst 6.5 + ATI Tray Tools 1.26.940 2x Seagate 320GB 7200.10s in RAID-0, WD2500KS hdd BenQ DW1650 DVD±RW, LITE-ON 52327S CD-RW FSP Epsilon 600W Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 302 LDT/FSB Frequency Ratio....................... - 3.0 CPU/FSB Frequency Ratio....................... - 9.0 PCI eXpress Frequency......................... - 103Mhz CPU VID StartUp Value......................... - 1.450v CPU VID Control............................... - 1.550v CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - 07.0 Nano Seconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Enable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: AquaMark3 ========== short description: 302x9x.9 @ 2718MHz, 1.67v (reported by CPU-Z & SmartGuardian) 3-4-4-8 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
loggan26 Posted October 20, 2006 Posted October 20, 2006 DFI LANPARTY NF4 Ultra SLI-D (04/06 BIOS) AMD X2 4200+ Manchester, Thermalright XP120, Yateloom 120mm Fan 2x512MB KingMax Hardcore PC4000 MSI GeForce 7900GTO, 720/1650 91.74 drivers 2X200GB Seagate Barracuda 7,200.10 (8mb) SATA HDD, Raid0 6.86 legacy drivers NEC 4551 DVDRW OCZ GameXstream 700W Sli ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 247 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 11 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.450v CPU VID Special Control....................... - Above VID * 110% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 03 Min RAS# active time (Tras)................... - 08 Row precharge time (Trp)...................... - 03 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== 2 x Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark ========== short description: 247x11 @ 2720Mhz, 1.450v + 110% 2.5-3-3-8 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
supertux1 Posted October 20, 2006 Posted October 20, 2006 DFI LANPARTY nF4 SLI-DR (7/04-2BTA BIOS) AMD Opteron 165 dual core CCBBE 0165EPMW 2x1024MB OCZ PC3200 (OCZ4002048ELDCPE-K) XFX Geforce 7950GX2, 607/1600 91.31 drivers 2x36GB Western Digital Raptor 10,000RPM SATA hdd raid 0 OCZ GamerXStream 700w Power Supply Swiftech APEX-H20 + DD-GX2 * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 325 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.550v CPU VID Control............................... - 1.550 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.70v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 12 Bus Clocks Row to Row delay (Trrd)....................... - 00 Bus Clock Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Increase DQS Skew Value................................ - 255 DRAM Drive Strength........................... - weak3 DRAM Data Drive Strength...................... - Normal3 Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Fastest Read Preamble Time............................ - 3.0ns IdleCycle Limit............................... - 000 Cycles Dynamic Counter............................... - Disabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 325x9 @ 2926Mhz, 1.55v 2.5-3-2-5 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted October 21, 2006 Posted October 21, 2006 DFI LANPARTY nF4 SLI-DR (406 BIOS) AMD X2 3800+ dual core LDBFE 0609 XPMW 2x1024MB Gskill pc3200 ZX’s PowerColor X1900xtx , 675-783 6.9 drivers 2x 74GB Western Digital Raptor 10,000RPM SATA hdd's in RAID0 NEC 3550a DVD Corsair HX520w Power Supply DangerDen = TDX + Maze4 + BIX2 + DDC-12v + 38 tubing * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 270 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.425 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v [/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7 DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 8 DRAM Response Time............................ - fast Read Preamble Time............................ - 5.5 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + MBM + A64Tweaker : http://img98.imageshack.us/img98/4092/3dmark01th4.jpg 3dMark2003 + CPU-Z + MBM + A64Tweaker + Everest Reads : http://img99.imageshack.us/img99/4695/3dmark03wk4.jpg 3dMark2005 + CPU-Z + MBM + A64Tweaker + Everest Writes : http://img90.imageshack.us/img90/221/3dmark05xk5.jpg 3dMark 2006 + CPU-Z + MBM + A64Tweaker + Everest Latency : http://img98.imageshack.us/img98/4663/3dmark06yy6.jpg ========== short description: 270x10 @ 2700Mhz 2.5-3-5-2 @ 225mhz 2.7v Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now