EllisD Posted October 21, 2006 Posted October 21, 2006 DFI LANPARTY nF4 Ultra-D (03/29/2006 BIOS) AMD Opteron 165 CCBWE 05510 WMPW 2x1024MB Gskill PC-4000 (F1-4000USU2-2GBHZ) ATi Radeon X1900XT (XTX BIOS), 685/1602 Omega 6.9 Drivers Maxtor: 120GB SATA (OS), 200 IDE (STORAGE) Western Digital: 400GB SATAII (STORAGE) Plextor PX-716SA DVD-RW SATA Antec NeoHE 550 PSU * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 289 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - x9.0 PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.250V CPU VID Special Control....................... - Above VID +123% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 15 Bus Clocks Row refresh cyc time (Trfc)................... - 17 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 04 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - LvL 7 DRAM Data Drive Strength...................... - LvL 3 Max Async Latency............................. - 9.0ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.5ns IdleCycle Limit............................... - 016 Cycles Dynamic Counter............................... - Enable R/W Queue Bypass.............................. - 08 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: http://i92.photobucket.com/albums/l38/Elli...iTool3dm2k1.jpg 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark3: ========== short description: 289x9 @ 2601Mhz, 1.52V 3-4-8-4 @ 2.70v vdimm (2.78 DMM) Share this post Link to post Share on other sites More sharing options...
sailindawg Posted October 22, 2006 Posted October 22, 2006 DFI LP SLI-DR Expert (06/04/2006 BIOS) AMD Athlon 64 X2 4400+ (Toledo - CCBIE 0610 DPMW) TT Big Typhoon 2x1024MB Mushkin Redline eXtreme Performance PC4000 (991493 - Infineon CE-6) EVGA GeForce 7950 GX2, 500/1200 91.47 drivers 1 - Seagate SATA 120G hdd plus 2xSeagate IDE 120G HDD RAID 0 BenQ DW1620 DVD burner legacy cd/dvd ROM OCZ GamerX 700 Power Supply X-Fi Xtreme Music ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 285 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 102Mhz CPU VID StartUp Value......................... - Start-up CPU VID Control............................... - 1.375 CPU VID Special Control....................... - 104.8% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.59v DRAM Voltage Control.......................... - 2.87v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3684 DRAM Bank Interleave.......................... - Enabled Odd Divisor Correct........................... - Disable DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 3 (Reduce 15%) Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark2006: ========== short description: 285X10 @ 2850Mhz, (1.375v)(104.8%) cpu voltages 3-3-8-2 @ 2.87v(2.83v BIOS reading) vdimm Share this post Link to post Share on other sites More sharing options...
catkicker Posted October 24, 2006 Posted October 24, 2006 DFI LANPARTY nF4 SLI-DR (BIGTOE tweaked 7/04-2a BIOS) AMD 165 Opteron dual core CCBBE 0610DPMW 2x1024MB G.SKILL Extreme F1-4000USU2-2GBHZ EVGA 7950GX2, 510/611_ 91.47 drivers 2x80 gig.Seagate SATA hdd raid 0 LITEON SHM-165H6S 16X Super Allwrite OCZ gameXstreme 700watt Supply * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 311 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.275V CPU VID Special Control....................... - 113% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 04 Min RAS# active time (Tras)................... - 08 Row precharge time (Trp)...................... - 04 Row Cycle time (Trc).......................... - 09 Bus Clocks Row refresh cyc time (Trfc)................... - 17 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Enable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 10.0 Nano Seconds DRAM Response Time............................ - Fast Read Preamble Time............................ - 08.0 Nano Seconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Enable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 311x9 @ 2800Mhz, 3-4-8-4 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
acphydro Posted October 25, 2006 Posted October 25, 2006 DFI LANPARTY UT nF4 Ultra-D Socket 939 NVIDIA nForce4 Ultra 704-2bt BIOS AMD Athlon 64 X2 3800+ Socket 939 Processor ADA3800BVBOX - LDBFE 0625 APAW 2x1024MB Patriot PDC2G4000ELK DDR500/PC4000 Dual Channel Eased Latency - Samsung UCCC XFX PVT71PUDE3 GeForce 7900GS 256MB GDDR3 PCI Express x16 XT Edition Video Card - Retail @ 620/820 Maxtor DiamondMax 10 6L200P0 200GB 7200 RPM IDE Ultra ATA133 Hard Drive w/16MB Buffer Seagate Barracuda 7200.10 ST3300620A 300GB Ultra ATA/100 7200RPM Hard Drive w/16MB Buffer NEC 16X DVD+/-R DVD Burner Black IDE/ATAPI Model ND-3550A Lite-On DVD+/-RW SOHW 1633S OCZ GameXStream OCZ600GXSSLI ATX12V 600W Power Supply ARCTIC COOLING Freezer 64 Pro Cooling Fan with Heatsink * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency - 305 LDT/FSB Frequency Ration - Auto CPU/FSB Frequency Ratio - 9x PCI eXpress Frequency - 101Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.450v CPU VID Special Control - Avove VID * 104% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.70v [/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set - 166 (DRAM/FSB:5/06) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - Auto Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - Auto Write recovery time (Twr) - Auto Write to Read delay (Twtr) - Auto Read to Write delay (Trwt) - Auto Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 4 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: http://img521.imageshack.us/img521/8830/x21iy3.jpg 3dMark2003: 3dMark2005: 3dMark2006: Everest Ultimate Edition 3 Series Memory Read http://img339.imageshack.us/img339/7681/x25su8.jpg Aquamark 3d: http://img251.imageshack.us/img251/8445/x26lk5.jpg ========== short description: 305x9 @ 2750Mhz, 1.450v + 104% 3-4-4-8 @ 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
mknwatt Posted October 27, 2006 Posted October 27, 2006 DFI LANPARTY NF4 Expert (04/06/2006 BIOS) AMD Athlon64 4000+ (San Diego - KACAE 0601GPEW) 2x 1024MB OCZ PC3200 EL Dual CH Platinum Edition BFG 7600GT OC 256MG , 580/1440 91.47 2x Western Digital WD1600JS 160GB 7200 SATAII - RAID 0 Lite-On DVD RW OCZ GXS 700W ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 240 MHz LDT/FSB Frequency Ratio....................... - x 4.0 CPU/FSB Frequency Ratio....................... - x 12.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.325V CPU VID Special Control....................... - Above VID * 121.6% LDT Voltage Control........................... - 1.30V Chip Set Voltage Control...................... - 1.56V DRAM Voltage Control.......................... - 2.80V[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set (MHz).................... - 200=RAM/FSB:01/01 Command Per Clock (CPC).................... - Enable CAS Latency Control (Tcl).................... - 3.0 RAS# to CAS# delay (Trcd)................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp).................... - 03 Bus Clocks Row Cycle time (Trc).................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)................... - 03 Bus Clocks Write recovery time (Twr).................... - 03 Bus Clocks Write to Read delay (Twtr)................... - 02 Bus Clocks Read to Write delay (Trwt)................... - 03 Bus Clocks Refresh Period (Tref)................... - 3120 Cycles Odd Divisor correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 08 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 07.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 05.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts)[/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 3.50.761: 3dMark2003: 3dMark2005: 3dMark2006: ========== short description: 240x12 @ 2880 MHz, 1.325v + 121.6% 3-3-8-3 @ 2.80V vdimm Share this post Link to post Share on other sites More sharing options...
Knavinusa Posted October 29, 2006 Posted October 29, 2006 DFI Lanparty NF4 Ultra-D AMD Opteron 165 Toledo (CCBBE 0615DPMW) 2x 1024 MB PC3200 OCZ EL Platinum BFG GeForce 7900 GT (580/1830) Seagate Barracuda 320 GB SATA Seagate Barracuda 300 GB SATA Lite-On 1213S DVD-RW Enermax Liberty 620W ====== [b]Genie BIOS Settings:[/b] [color="red"]FSB Bus Frequency............................. - 300 MHz LDT/FSB Frequency Ratio....................... - x 3.0 CPU/FSB Frequency Ratio....................... - x 9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.35V CPU VID Control............................... - 1.35V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20V Chip Set Voltage Control...................... - 1.70V DRAM Voltage Control.......................... - 2.60V[/color] [b]DRAM Configuration Settings:[/b] [color="red"]DRAM Frequency Set (MHz)...................... - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 00 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Normal4 DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) Max Async Latency............................. - 08.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts)[/color] ====== Prime95: CPU-Z: Everest: 3DMark2001: 3DMark03: 3DMark05: 3DMark06: ====== short description: 300x9 @ 2.7 GHz, 1.35V 3-3-2-8 @ 225 MHz, 2.6V Share this post Link to post Share on other sites More sharing options...
Knavinusa Posted October 30, 2006 Posted October 30, 2006 DFI Lanparty NF4 Ultra-D (04/06/2006-2BTA) AMD Opteron 165 Toledo (CCBBE 0615DPMW) 2x 1024MB OCZ PC3200 EL Platinum BFG GeForce 7900 GT 256MB @ 590/1820 - 91.47 Seagate Barracuda 320 GB SATA Seagate Barracuda 300 GB SATA Lite-On 1213S DVD-RW Enermax Liberty 620W ============ [B]Genie BIOS Settings:[/B] [COLOR="Red"] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9.0 PCI eXpress Frequency......................... - 105 MHz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.350V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20V Chip Set Voltage Control...................... - 1.70V DRAM Voltage Control.......................... - 2.80V [/COLOR] [B]DRAM Configuration Settings:[/B] [COLOR="Red"] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 00 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6.0ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Enable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/COLOR] ============ Prime95 + 3DMark2001 + CPU-Z EVEREST Ultimate Edition 3DMark03 3DMark05 3DMark06 AquaMark 3 ============ short description: 300x9 @ 2700 MHz, 1.35V 2.5-3-2-8 @ 225 MHz, 2.8V Share this post Link to post Share on other sites More sharing options...
dr_bowtie Posted November 2, 2006 Posted November 2, 2006 DFI LANPARTY nF4 SLI-DR (7/04-2BTA BIOS) AMD Opteron 148 CABYE / XP-90 2x512 Patriot-XBLK-3200 BFG GeForce 6600GT, 97.31 drivers 160gig Seagate Sata II NEC 3550 DVD-RW OCZ 620w Powerstream PSU * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.400 CPU VID Special Control....................... - +110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.90v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 3dMark2003: 3dMark2005: 3dMark 2006: Evererst 2.2 + S/G ========== short description: 300x10 @ 3000Mhz, 1.5 cpu voltages 3-4-8-4 @ 2.93v vdimm Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted November 4, 2006 Posted November 4, 2006 DFI LANPARTY nF4 SLI-DR Expert (04/06/06 BIOS) AMD Athlon FX-60 (CCB2E 0608EPDW) (Cooled by modified Thermaltake BigWaterSE w/AS5) 2x512MB OCZ PC4800 Platinum Limited Edition (OCZ600512EEPE) XFX GeForce 7900GTX XXX EDITION, 710/1800 (Modded BIOS) 93.71 drivers 36GB Western Digital Raptor 10,000RPM SATA hdd Plextor 16x Dual Layer DVD Burner (SATA) Fortron Epsilon 700 WATT Quad SLI PSU ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 245 LDT/FSB Frequency Ratio....................... - 3.0 CPU/FSB Frequency Ratio....................... - 12.0 PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.475V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.87v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 250=RAM/FSB:05/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 10 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 5 DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 5.0ns IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest: 3DMark03: 39191 3DMark05: 15610 3DMark06+AM3: 10070/122313 ========== short description: 245x12 @ 2940Mhz, 1.475V cpu voltage 2.5-4-4-10-1T @ 2.87v vdimm Share this post Link to post Share on other sites More sharing options...
madian225 Posted November 6, 2006 Posted November 6, 2006 DFI LANPARTY nF4 SLI-DR Venus (06th April 2006 BIOS) AMD 170 Opteron Dual Core - Naked - 2x1024MB Mushkin Redline Extreme (991493) XFX GeForce 7800GTX Extreme Edition, 490/1300 91.47 drivers 36GB Western Digital Raptor 10,000RPM SATA hdd * 2 - Raid 0 Enermax 600 ATX 24 pin Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 281 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.45 CPU VID Special Control....................... - 102.4 % LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.56v DRAM Voltage Control.......................... - 2.71v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 7 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disabled DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 8.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 5.0 Nano Seconds IdleCycle Limit............................... - 064 Cycles Dynamic Counter............................... - Enable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 3.50.761: http://i47.photobucket.com/albums/f169/mad...overclockv2.jpg 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 281x10 @ 2810Mhz, 1.45v @ 102.4% 2.5-3-7-2 @ 2.71v vdimm Share this post Link to post Share on other sites More sharing options...
techman62 Posted November 13, 2006 Posted November 13, 2006 DFI LANPARTY nF4 Ultra-D (4/06/06 BIOS) AMD Opteron 165 CCBBE 0610DPMW 2x1024MB G.Skill PC4000 HZ's (F1-4000USU2-2GBHZ) Evga GeForce 7900GT, 585/812 84.21 drivers 2x200GB Maxtor DiamondMax 10 SATA HDD's in Raid 0 HP dvd840 DVD-ROM OCZ GameXSteam 700w Power Supply * * * * * ========== Genie BIOS Settings: FSB Bus Frequency............................. - 325 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.50v CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v DRAM Configuration Settings: DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 00 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3684 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 7 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 5.0ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark2006: AquaMark3: ========== short description: 325x9 @ 2925Mhz, 1.50 cpu voltages 3-4-8-4 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
Guest drteming Posted November 14, 2006 Posted November 14, 2006 DFI LANPARTY UT nF4 Ultra-D, SLI Mod (BIOS 04/06/2006) Opteron 165 CCBBE 0610DPMW 2x1024MB OCZ PC4000EB (OCZ5001024EBPE) eVGA 7900 GTO (696/800), 93.71 drivers Hitachi 80GB SATA II x 2 - Raid 0 || Western Digital Caviar SE 250GB SATA II NEC 3540 DVD-RW || Lite-On SOHR-5238S CD-RW || Samsung SFD321B/LBL1 FDD OCZ Powerstream 520W * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - x 3.0 CPU/FSB Frequency Ratio....................... - x 9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.550v CPU VID Special Control....................... - Above VID * 104% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 6 DRAM Data Drive Strength...................... - Level 1(Reduce 50%) Max Async Latency............................. - 9 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6.5 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3DMark2001SE + CPU-Z + Everest 2.20: 3DMark2003: 3DMark2005: 3DMark 2006: AquaMark3: ========== short description: 334x9 @ 3006Mhz, 1.550v x 104%, 1.612v 3-3-8-2 @ 273Mhz, 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now