CPDMF Posted January 28, 2007 Posted January 28, 2007 DFI LANPARTY nF4 SLI-DR eXpert (E7/04-2BTA BIOS) AMD Opteron 165 CCBBE 0617fpmw 2x1024MB G.Skill HZ PC4000 UCCC XFX 7800GT + EVGA 7800GT SLI, 92.91 drivers 2 X 80G Hitachi SATAII RAID0 D4 pump/ MP05 pro/ BIX2 OCZ 600W Powerstream SLI * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 345 LDT/FSB Frequency Ratio....................... - X3 CPU/FSB Frequency Ratio....................... - X9 PCI eXpress Frequency......................... - 113Mhz CPU VID StartUp Value......................... - startup CPU VID Control............................... - 1.35 CPU VID Special Control....................... - 119.2% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.68v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 00 Row precharge time (Trp)...................... - 8 Row Cycle time (Trc).......................... - 13 Bus Clocks Row refresh cyc time (Trfc)................... - 17 Bus Clocks Row to Row delay (Trrd)....................... - 00 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3684 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level7 DRAM Data Drive Strength...................... - Level1 Max Async Latency............................. - 9 DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.5 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 345x9 @ 3105Mhz, 1.61v 3-4-00-4 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
soundx98 Posted January 28, 2007 Posted January 28, 2007 DFI NF4 Ultra-D @ 2800MHz – XP Pro 32-Bit DFI LANPARTY nF4 Ultra-D (Rev.AE1) Tony’s 704-2bta w/MemTest 1.70+ by Tmod AMD Opteron 170 CCB1E 0550VPMW Dual Core (nekid) 2x 512 Corsair CMX512-3200XL (XMS3208v1.1) eVGA 6800GS 256MB, nVidia 93.71 drivers Seagate 7200.8 200Gb ATA100 HDD NEC-3550A DVD R/RW Silver SkyHawk 620 Power One Series PSU Arctic Cooling Freezer 64 Pro $9.95 “Fake” G5 Case * ========== Genie BIOS Settings: FSB Bus Frequency - 280 LDT/FSB Frequency Ratio - 3.0 CPU/FSB Frequency Ratio - x10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.35v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 140=RAM/FSB:07/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 11 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 04 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 4 Normal DRAM Data Drive Strength - Level 3 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Normal Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Ebaled R/W Queue Bypass - 08 x Bypass Max - 04 x 32 Byte Granularity - Disable (4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.38: 3dMark2003: 3dMark2005: 3DMark 2006 ========== short description: 280 x 10 = 2800MHz 2-2-6-2 @ 2.80 vdimm Share this post Link to post Share on other sites More sharing options...
centy Posted January 28, 2007 Posted January 28, 2007 DFI LANPARTY nF4 SLI-D (704-2BT BIOS) AMD A64 4000+ San Diego KABGE 0528GPMW 2x1024MB G.Skill HX PC3200(DDR400) (F1-3200BIU2-2GBHX) Leadtek GeForce 7800GTX, 450/1250 Forceware 84.21 drivers 120GB Western Digital Caviar 7,200RPM SATA 8MB Cache hdd (WDC WD1200JD-00GBB0) 250GB Seagate Baracuda 7200.8 7,200RPM SATA NCQ 8MB Cache hdd (ST3250823AS) NEC ND4550A DVD-RAM SuperMulti Drive 2MB Cache Tagan TG530-U15 530w ATX v2.01 Modular Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 275 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.425v CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 0 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 01 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 1816 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Weak 3 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - 7.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 4.0 ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3DMark 2001SE + CPUZ 3DMark 03 3DMark 05 3DMark 06 Aquamark 3 ========== short description: 275 x 10 = 2750MHz, 1.52v 2-3-0-2 @ 2.70 vdimm Not battlefield 2 stable (Damn Infineon). Making a new OCDB entry which is. Use CPC disabled/2T to stabilise 3D with these settings. Share this post Link to post Share on other sites More sharing options...
Guest laydback Posted January 29, 2007 Posted January 29, 2007 DFI Lanparty UT NF4 Ultra-D R.AB0 704-2bta AMD Opteron146 Venus CAB2E 0540FPMW 2x512 GeiL Ultra-X PC4400 TCCD BFG 7900GT, XG Optimized Driver 97.72 250gb Western Digital Diamondmax 10 ATA133 160gb+80gb Seagate Barracuda SATA in RAID 0 FSP Group FX700-GLN ATX12V 700W PSU Cooled By: Dangerden DDC12v,MAZE4GPU,Dual bay res,BlackIce Pro Rad,Swiftech Apogee,2x120mm Heatercore Thermaltake Armor Black Viewsonic 19" LCD - VA912b Compaq 17" LCD - TFT7020 Logitech X-530 Surround * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 315 LDT/FSB Frequency Ratio....................... - 1x CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.475 CPU VID Special Control....................... - x110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:5/6 Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 3 Write recovery time (Twr)..................... - 3 Write to Read delay (Twtr).................... - 2 Read to Write delay (Trwt).................... - 3 Refresh Period (Tref)......................... - 3120 DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 10 DRAM Response Time............................ - Fast Read Preamble Time............................ - 7 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3dMark2001SE + CPU-Z + Everest: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 315x10, 3150mhz, 1.60vcore 2x512, 5:6, 2.80vdimm Share this post Link to post Share on other sites More sharing options...
Likwid Posted January 30, 2007 Posted January 30, 2007 DFI LANPARTY UT nF4 SLI-DR Expert (04/06 BIOS) Opteron 170 CCBBE 0610DPMW 2x1024MB OCZ Gold PC4000EL (OCZ5001024ELGE-K) 2X eVGA GeForce 7800GT, 554/1215 91.47 drivers 2X 74GB Western Digital Raptor 10,000RPM SATA hdd (RAID0) LiteOn DVD/RW w/ Lightscribe OCZ Powerstream 520w Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 302 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.425v CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.56v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 2560 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 7 DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - 08.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 Nano Seconds IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== ORTHOS + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 302x10 @ 3020Mhz, 1.425 x 110% 3-4-8-3 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
ReverendRun Posted January 31, 2007 Posted January 31, 2007 DFI LANPARTY nF4 Ultra-D (6/23 BIOS) AMD Opteron 165 (CCBWE 0551VPMW) 2x512MB G.Skill PC4400 (F1-3200DSU2-1GBLC) eVga GeForce 7900GT, 530/1560 93.71 drivers 160GB Segate 7200.7 SATA hdd NEC 3550A DVD-ROM OCZ PowerStream 520 ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 280 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.375v CPU VID Control............................... - 1.375v CPU VID Special Control....................... - Above VID * 104% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 03 RAS# to CAS# delay (Trcd)..................... - 04 Min RAS# active time (Tras)................... - 08 Row precharge time (Trp)...................... - 04 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 07 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 08 Bus Clocks Refresh Period (Tref)......................... - 3684 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Increase Skew DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 6 DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 07.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 05.0 Nano Seconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 280x9 @ 2520Mhz, 1.392v 3-4-4-8 @ 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
KimTjik Posted February 1, 2007 Posted February 1, 2007 DFI Lanparty UT nF4 Ultra-D Rev A3 (N4d623-2) AMD Opteron 180 dual core (LCB9E 0630BPMW) 2x512MB GeiL Ultra-X PC3200 400MHz CL2 5-2-2 (GLX1GB3200DC) BH-5 HIS 800GTO 256mb PCI-E x16, 525/1100 Omega 3.8.252 drivers 74GB Western Digital Raptor 10,000RPM SATA hdd Sony DRU-810A CD/DVD RW Fortron Epsilon 600W (FX600-GLN) * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 240 LDT/FSB Frequency Ratio....................... - 4 CPU/FSB Frequency Ratio....................... - 12 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.350v CPU VID Control............................... - 1.400v CPU VID Special Control....................... - Above VID * 104% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:9/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.0 RAS# to CAS# delay (Trcd)..................... - 2 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 10 Bus Clocks Row to Row delay (Trrd)....................... - 0 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 01 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 7 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE (30 867) + CPU-Z: http://i77.photobucket.com/albums/j49/KimTjik/Screen2882.png 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 240x12 @ 2880Mhz, 1.456 cpu voltages 2-2-5-2 @ 221Mhz, 2.8v vdimm Share this post Link to post Share on other sites More sharing options...
Guest s3x0rc1s+ Posted February 2, 2007 Posted February 2, 2007 Hello All, New to DFI Lanparty Boards but after hours of Overclocking my system i finally scored a 15008 on 3Dmarks 05 and i was wondering if this is a good score or not as i am new to overclocking DFI Boards when i first built the system i score 7890 then after more tweaking i scored 12670 and after more tweaking lol i scored 14957 and now i reached 15008! :-) Or if anyone has Advice on how to up my score. Pics Below. 1. http://img.photobucket.com/albums/v512/ghostsniper77/O.jpg 2. http://img.photobucket.com/albums/v512/gho...ettingtheir.jpg 3. http://img.photobucket.com/albums/v512/gho...08on3Dmarks.jpg Share this post Link to post Share on other sites More sharing options...
dr_bowtie Posted February 6, 2007 Posted February 6, 2007 Asus A8V-VM (0502 Bios) Via K8M890 N/B VT8251 S/B AMD 148 Opteron single core 2x512 Patriot PDC1G3200LLK EVGA 7600gt, 560/1400 93.71 80gig Hitachi 7200rpm Sata II Sony DVD rom DDU1612 Aspire AS500w PSU ========== [b]Advanced BIOS Settings:[/b][color=red]Memclock Mode................................ - (Limit)Memclock Value................................ - 200MCT Timing Mode.............................. - (Manual)CAS Latency CL................................ - 2.5TRAS.............................................. - 7TRP................................................ - 3TRCD.............................................. - 3CMD-ADDR Timing Mode..................... - (1T) AI Overclock Tuner............................ - (Manual)CPU Frequency.................................. - 235AGP/PCI Frequency............................. - (66.6/33.3) PCI Frequency Mode............................ - (100Mhz)DDR Reference Voltage......................... - (2.6v)[/color] [color=green][b][size=3]==========[/color][/b][/size] SP2004 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: [color=green][b][size=3]==========[/color][/b][/size] [b]short description: 235x11 @ 2585Mhz, Auto cpu voltages2.5-3-3-7 @ 2.60v vdimm[/b] Share this post Link to post Share on other sites More sharing options...
Chump Posted February 8, 2007 Posted February 8, 2007 DFI LANPARTY UT NF4 SLI-DR EXPERT (406 BIOS) AMD OPTERON 165 CCBBE 0617 FPMW TUNIQ TOWER 120 AIR COOLING 2 X 512MB OCZ PLATINUM REV 2 PC3200EL (OCZ4001024ELDCPE-K) XFX GeForce 6800GT, OC 420/1190 Arctic Cooling NV Silencer 5 93.71 Drivers 250GB MAXTOR MAX-LINE SATA-2 HDD (7V250FO SONY DL DVD-RW DRU-820A OCZ GAMEXSTREEM 700W PSU ========== [B]Genie BIOS Settings:[/B] [COLOR=red]FSB Bus Frequency............................. - 325[/COLOR] [COLOR=red]LDT/FSB Frequency Ratio....................... - 4[/COLOR] [COLOR=red]CPU/FSB Frequency Ratio....................... - 9[/COLOR] [COLOR=red]PCI eXpress Frequency......................... - 100Mhz[/COLOR] [COLOR=red]CPU VID StartUp Value......................... - Startup[/COLOR] [COLOR=red]CPU VID Control............................... - 1.50v[/COLOR] [COLOR=red]CPU VID Special Control....................... - Auto[/COLOR] [COLOR=red]LDT Voltage Control........................... - 1.40v [/COLOR] [COLOR=red]Chip Set Voltage Control...................... - 1.84v[/COLOR] [COLOR=red]DRAM Voltage Control.......................... - 2.92v[/COLOR] [B]DRAM Configuration Settings:[/B] [COLOR=red]DRAM Frequency Set............................ - 166=RAM/FSB:05/06[/COLOR] [COLOR=red]Command Per Clock (CPC)....................... - Enable [/COLOR] [COLOR=red]CAS Latency Control (Tcl)..................... - 2.5[/COLOR] [COLOR=red]RAS# to CAS# delay (Trcd)..................... - 3[/COLOR] [COLOR=red]Min RAS# active time (Tras)................... - 6[/COLOR] [COLOR=red]Row precharge time (Trp)...................... - 3[/COLOR] [COLOR=red]Row Cycle time (Trc).......................... - 07 Bus Clocks[/COLOR] [COLOR=red]Row refresh cyc time (Trfc)................... - 14 Bus Clocks[/COLOR] [COLOR=red]Row to Row delay (Trrd)....................... - 02 Bus Clocks[/COLOR] [COLOR=red]Write recovery time (Twr)..................... - 02 Bus Clocks[/COLOR] [COLOR=red]Write to Read delay (Twtr).................... - 02 Bus Clocks[/COLOR] [COLOR=red]Read to Write delay (Trwt).................... - 03 Bus Clocks[/COLOR] [COLOR=red]Refresh Period (Tref)......................... - 4708 Cycles[/COLOR] [COLOR=red]Odd Divider Correct........................... - Disable[/COLOR] [COLOR=red]DRAM Bank Interleave.......................... - Enabled[/COLOR] [COLOR=red]DQS Skew Control.............................. - Auto[/COLOR] [COLOR=red]DQS Skew Value................................ - 0[/COLOR] [COLOR=red]DRAM Drive Strength........................... - Level 08[/COLOR] [COLOR=red]DRAM Data Drive Strength...................... - Auto[/COLOR] [COLOR=red]Max Async Latency............................. - Auto[/COLOR] [COLOR=red]DRAM Response Time............................ - Fastest[/COLOR] [COLOR=red]Read Preamble Time............................ - Auto[/COLOR] [COLOR=red]IdleCycle Limit............................... - Auto[/COLOR] [COLOR=red]Dynamic Counter............................... - Auto[/COLOR] [COLOR=red]R/W Queue Bypass.............................. - Auto[/COLOR] [COLOR=red]Bypass Max.................................... - Auto[/COLOR] [COLOR=red]32 Byte Granularity........................... - Auto[/COLOR] ========== Stress Prime 2004 Orthos Edition + 3dMark2001SE + CPU-Z 3dMark2003: 3dMark2005: 3dMark 2006: ========== Short Description: OPTERON 165 CCBBE 0617 FPMW 325x9 = 2925Mhz 1.5V In BIOS 2.5-3-6-3 @ 2.92v VDIMM In BIOS Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted February 9, 2007 Posted February 9, 2007 DFI LANPARTY nF4 SLI-DR Expert (04/06/06 BIOS) AMD Opteron 185 (CCBBE 0613) (Cooled by modified Thermaltake BigWaterSE w/AS5) 2x 1GB Mushkin XP4000 Redline (991493) EVGA 8800GTX video card, 620/1940, 97.92 drivers 36GB Western Digital Raptor 10,000RPM SATA hdd Plextor 16x Dual Layer DVD Burner (SATA) Fortron Epsilon 700 WATT Quad SLI PSU ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 LDT/FSB Frequency Ratio....................... - 3.0 CPU/FSB Frequency Ratio....................... - 12.0 PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.525V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.62v DRAM Voltage Control.......................... - 2.71v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 6 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 7 DRAM Data Drive Strength...................... - Level 1 (50% reduced) Max Async Latency............................. - 7.0 DRAM Response Time............................ - Normal Read Preamble Time............................ - 4.5 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE (42499) + CPU-Z + Everest: 3DMark03: 31913 3DMark05: 16045 3DMark06: 10392 ========== short description: 250x12 @ 3GHz, 1.525V cpu voltage 3-3-2-6-1T @ 2.71v vdimm Share this post Link to post Share on other sites More sharing options...
centy Posted February 16, 2007 Posted February 16, 2007 DFI LANPARTY nF4 SLI-D (704-2BT BIOS) AMD A64 4000+ San Diego KABGE 0528GPMW 2x1024MB G.Skill HX PC3200(DDR400) (F1-3200BIU2-2GBHX) Leadtek GeForce 7800GTX, 490/1340 Forceware 92.91 drivers 120GB Western Digital Caviar 7,200RPM SATA 8MB Cache hdd (WDC WD1200JD-00GBB0) 250GB Seagate Baracuda 7200.8 7,200RPM SATA NCQ 8MB Cache hdd (ST3250823AS) NEC ND4550A DVD-RAM SuperMulti Drive 2MB Cache Tagan TG530-U15 530w ATX v2.01 Modular Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 229 LDT/FSB Frequency Ratio....................... - 4x CPU/FSB Frequency Ratio....................... - 12x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.425v CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 0 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 01 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 1816 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Weak 3 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - 7.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 4.0 ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3DMark 2001SE + CPUZ 3DMark 03 3DMark 05 3DMark 06 Aquamark 3 ========== short description: 229 x 12 = 2750MHz, 1.52v 2.5-3-0-2 @ 2.70 vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now