blinker0 Posted December 20, 2005 Posted December 20, 2005 DFI LANPARTY nF4 SLI-D - 6/23-2 BIOS AMD Opteron 148 CAB2E 0545 CPBW OCZ4001024ELDCGE-K BFG 7800GT OC 256MB,585/1224 ,8.1.9.5 Drivers 2X Seagate 80 Gig RAID Stripe o (8MB cache) Sony DRU800A DVD OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail * * ========== Genie BIOS Settings: FSB Bus Frequency - 333 LDT/FSB Frequency Ratio - 2X CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.47v CPU VID Control - 1.500v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 3.50v DRAM Configuration Settings: DRAM Frequency Set - 150=RAM/FSB Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 14 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 133 3.9US Cycles Write CAS Latency (Twcl) - 1 DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 7.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 05 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 : 3dMark2003: 3dMark2005 + EVEREST 2.01: AQUAMARK: ========== short description: 333x9 @ 3003Mhz, 1.500v + 113% 2-2-5-2 @ 3.5v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted December 21, 2005 Posted December 21, 2005 DFI LANPARTY nF4 Expert SLI-DR (12/07/2005 BIOS) AMD Opteron 146 (Venus core) 2x1024MB Crucial Ballistix PC4000 XFX GeForce 7800GT, 501/1270 81.85 drivers Western Digital Raptor 36GB 10,000RPM SATA hdd Asus 52x Quiet-Trak CD-ROM Skyhawk 520w 24-pin ATX power supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 275 LDT/FSB Frequency Ratio....................... - x 3.0 CPU/FSB Frequency Ratio....................... - x 10.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.400v CPU VID Special Control....................... - Above VID * 109.6% LDT Voltage Control........................... - 1.40v Chip Set Voltage Control...................... - 1.68v DRAM Voltage Control.......................... - 3.17v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 4708 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/nf4/e...46_275x10-1.gif 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 275x10 @ 2750Mhz, 1.400v + 109.6% 3.0-3-8-3 @ 3.17v vdimm Share this post Link to post Share on other sites More sharing options...
Guest laydback Posted December 22, 2005 Posted December 22, 2005 DFI LANPARTY nF4 Ultra-D - 704-2BTA BIOS AMD Opteron146 CAB2E 0540FPMW 2x512MB GeiL One S (TCCD)(Orange Slots) BFG 7800GT OC, 520/650 81.95 DH Zeropoint Maxtor 250GB ATA133 Western Digital 250GB SATAI SBLive! 24-bit PCI Enermax EG651PVE-FM 24p / 12v=36a 5v=36a 3.3v=36a Zalman Reserator Plus! Dual Swiftech MCP-350 Pumps Thermaltake Aquabay M2 Radiator * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.450v CPU VID Special Control - Above VID * Auto LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 17 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 1 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.5 Nano Seconds IdleCycle Limit - 0 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31 + Everest: 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 300x10 @ 3000Mhz, 1.450v + Auto 2-3-3-6 @ 2.9v vdimm Share this post Link to post Share on other sites More sharing options...
TheFlowerKing Posted December 22, 2005 Posted December 22, 2005 DFI LANPARTY nF4 Ultra-D - 0510-2FIX BIOS AMD Opteron 148 CABYE 0543 FPMW Venus 2x512MB Geil One S (tccd) in Orange slots Connect3D X800GTO modded to 16 pipelines, 560/1080 5.11(?) drivers Samsung 80GB SATA hdd (8MB cache) FSP BlueStorm 460W ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.475v CPU VID Special Control - AUTO LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.700v Add 0.3v - Enable DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/1 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 1 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE (31878) + CPU-Z 1.31 + A64Tweaker: http://img408.imageshack.us/img408/4290/pr...878a64tweak.jpg 3dMark2003 (14134) + Everest Read (6671): http://img408.imageshack.us/img408/7722/3d...estreadis66.jpg 3dMark2005 (6738) + Everest Write (2774): http://img254.imageshack.us/img254/2107/3d...stwriteis27.jpg Aquamark 3d (92286): http://img254.imageshack.us/img254/1984/aq...kis922869wc.jpg ========== short description: 300x10 @ 3000Mhz, 1.475v 300MHz @ 2.5-3-3-5 @ 2.73v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted December 23, 2005 Posted December 23, 2005 DFI Ultra-D - 510-2fix 3200 Venice 2x512mb OCZ Gold BH5 UTT (yellow slots) Power Color x850xt 1.66vGpu @ 630/630 Omega 5.12's 2x 36gig Raptors Raid0 ASUS IDE CD-ROM Drive OCZ 600w Power Stream SLI Edition DangerDen = TDX + Maze4 + BIX2 + DDC-12v + 38 tubing * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 280 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 10.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.50v CPU VID Control - 1.475v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 3.5v DRAM Configuration Settings: DRAM Frequency Set - 180 (9/10) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 15 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Increase DQS Skew Value - 0 DRAM Drive Strength - 8 DRAM Data Drive Strength - 1 Max Async Latency - Auto DRAM Response Time - Fastest Read Preamble Time - Auto IdleCycle Limit - 64 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + 2xCPU-Z + MBM : http://img375.imageshack.us/img375/1501/untitled1xl.jpg 3dMark2003 : http://img375.imageshack.us/img375/8333/untitled22ei.jpg 3dMark2005 : http://img375.imageshack.us/img375/7889/untitled39jb.jpg Everest : http://img375.imageshack.us/img375/8853/untitled44jg.jpg ========== short description: 280x10=2800mhz 2-2-5-2-7-15 3.5vdimm Share this post Link to post Share on other sites More sharing options...
cler1c Posted December 23, 2005 Posted December 23, 2005 DFI LANPARTY nF4 SLI-DR Expert - 02/11/2005 BIOS AMD Athlon64 3200+ Venice 512k L2 2x1024MB Mushkin (991483) orange slots[/size] 1x ATI Radeon x800xl @ stock, 5.12 drivers 2x160GB Hitachi Sata II Raid 0 Enermax 535w 24-pin PSU Thermalright SI-120 w/120mm Panaflo ultra high output * * ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.15v CPU VID Special Control - Above VID * 136% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.65v DRAM Voltage Control - 2.55v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clock DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 3 (Reduce 15%) Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fastest Read Preamble Time - 5.0 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://img355.imageshack.us/img355/831/pic19vs.jpg 3dMark2003: 3dMark2005: ========== short description: 260x10 @ 2600Mhz, 1.150v + 136% 3-4-8-3 @ 2.55v vdimm Share this post Link to post Share on other sites More sharing options...
TheFlowerKing Posted December 23, 2005 Posted December 23, 2005 DFI LANPARTY nF4 Ultra-D - 0510-3FIX BIOS AMD Opteron 148 CABYE 0543 FPMW Venus on Big Typhoon 2x512MB Twinmos Speed Premium PC3500 (bh-utt) in Yellow slots Connect3D X800GTO modded to 16 pipelines, 560/1080 5.11 drivers Samsung 80GB SATA hdd (8MB cache) FSP BlueStorm 460W ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.500v CPU VID Special Control - AUTO LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.400v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.5 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE (31592) + CPU-Z 1.31 + A64Tweaker: http://img435.imageshack.us/img435/6366/pr...592a64tweak.jpg 3dMark2003 (14081) + Everest Read (6133): http://img435.imageshack.us/img435/3213/3d...estreadis61.jpg 3dMark2005 (6725) + Everest Write (2639): http://img256.imageshack.us/img256/1889/3d...stwriteis26.jpg Aquamark 3d (91651): http://img256.imageshack.us/img256/6725/aq...kis916514tg.jpg ========== short description: 300x10 @ 3000Mhz, 1.500v 250MHz @ 2-2-2-5-7-12-2-2-1-2 @ 3.40v vdimm Share this post Link to post Share on other sites More sharing options...
TheFlowerKing Posted December 24, 2005 Posted December 24, 2005 DFI LANPARTY nF4 Ultra-D - 0510-3FIX BIOS AMD Opteron 148 CABYE 0543 FPMW Venus 4x512MB Twinmos Speed Premium PC3500 (bh-utt) in order from cpu : 84, 83, 79, 82 Connect3D X800GTO modded to 16 pipelines, 560/1080 5.11 drivers Samsung 80GB SATA hdd (8MB cache) FSP BlueStorm 460W ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3x CPU/FSB Frequency Ratio - 10x PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - AUTO CPU VID Control - 1.500v CPU VID Special Control - AUTO LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.300v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 12 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 01 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.5 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE (31117) + CPU-Z 1.31 + A64Tweaker: http://img517.imageshack.us/img517/8130/pr...117a64tweak.jpg 3dMark2003 (14034) + Everest Read (5904): http://img519.imageshack.us/img519/1428/3d...estreadis59.jpg 3dMark2005 (6699) + Everest Write (2405): http://img519.imageshack.us/img519/9153/3d...stwriteis24.jpg Aquamark 3d (89920): http://img247.imageshack.us/img247/882/aqu...kis899208dg.jpg ========== short description: 300x10 @ 3000Mhz, 1.500v 4x512MB @ 250MHz @ 2-2-2-5-7-12-2-2-1-2-2T @ 3.30v vdimm Share this post Link to post Share on other sites More sharing options...
MaKo Posted December 24, 2005 Posted December 24, 2005 DFI LANPARTY UT nF4 Ultra-D (623-2 Bios) AMD Opteron 148 (Venus core) 2X1024MB Crucial Ballistix PC4000 (BL2KIT12864Z503) BFG GeForce 7800 GT OC 256MB 500/1351 Forceware 82.12 Beta Drivers 2x Western Digital "Raptor" 74GB 10,000RPM SATA hdd (RAID-0) Western Digital WD2500KS 250MB SATAII hdd BenQ DW1620 Pro DVD Rewriter OCZ PowerStream OCZ520ADJ - 520W 24 pin ATX PSU * * * * ============ Genie BIOS Settings: FSB Bus Frequency............................. - 265 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - Auto PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.400v CPU VID Control............................... - 1.325v CPU VID Special Control....................... - Above VID * 110% LDT Voltage Control........................... - 1.40v Chip Set Voltage Control...................... - 1.70v DRAM Voltage Control.......................... - 2.60v DRAM Configuration Settings: DRAM Frequency Set............................ - 200=DRAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 04 Bus Clocks Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 15 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - AUTO Write CAS Latency (Twcl)...................... - AUTO DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 7 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) Prime95 + 3dMark2001SE (31854) + 2xCPU-Z 1.31 Everest Read (6936), SmartGuardian, NBench Everest Write (2539) + ClockGen 3dMark2003: 3dMark2005: Aquamark 3d: ============ short description: 265x11 @ 2915Mhz, 1.325v + 110% 3.0-4-8-4 @ 2.6v vdimm Share this post Link to post Share on other sites More sharing options...
NordicRX8 Posted December 29, 2005 Posted December 29, 2005 DFI LANPARTY nF4 Ultra-D 6/23-2 BIOS AMD Athlon64 3200+ Venice ZALMAN CNPS9500 2x512MB Mushkin! Enhanced PC-3500 Level II (BH-5) Connect3D X800GTO 256MB, 550/1082 Catalyst 5.11 Western Digital Raptor 36GB SATA-150 HDD Western Digital 160GB SATA-150 HDD NEC ND3550A Biege IDE DVD-RW DL NEC ND3540A Biege IDE DVD-RW DL OCZ PowerStream OCZ520ADJSLI ATX 520W Power Supply - Retail Vantec NXP-205 Fan Controller ========== Genie BIOS Settings: FSB Bus Frequency - 258 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.500v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 3.3v DRAM Configuration Settings: DRAM Frequency Set - 200 DRAM/FSB:1/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fastest Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.30: 3dMark2003: 3dMark2005: Everest Read: 7129 MB/s Everest Write: 2639 MB/s Everest Latency: 38.0 ns ========== short description: 258x10 @ 2580Mhz, 1.50v + 110% 2-2-5-2 1T @ 3.33v vdimm Share this post Link to post Share on other sites More sharing options...
mursaat Posted December 30, 2005 Posted December 30, 2005 DFI LANPARTY nF4 Ultra-D - 7/04-2 BigToe BIOS AMD Athlon64 3000+ Venice E6 0532FPMW 1x512MB OCZ PC3500 Gold EL (BH-5 New) Gainward 7800GT 256MB, 488/1241 81.98 drivers WD Raptor 36Gb SATA WD Caviar WD2000JD 200Gb 8Mb SATA Pioneer 109 DVD Burner PATA Lite-On 16P9 DVD PATA Levicom 420W ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.350v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.20v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 2560 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level nomal 4 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 7.0 Nano Seconds IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 Everest: Read 3823 Write 1632 Latency 36.3 (With 1 x 512Mb) 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 300x9 @ 2700Mhz, 1.400v + 113% 2-2-5-2 @ 3.2v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted December 31, 2005 Posted December 31, 2005 DFI Ultra-D - 704-2Bta x2 3800 Retail - LDBHE 0538RPMW 2x1024 Crucial Ballistix z503's (Orange Slots) Power Color x850xt 1.66vGpu @ 630/630 w/5.13's 2x 36gig Raptors Raid0 ASUS IDE CD-ROM Drive OCZ 600w Power Stream SLI Edition DangerDen = TDX + Maze4 + BIX2 + DDC-12v + 38 tubing * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - 3 CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.55v CPU VID Control - 1.55v CPU VID Special Control - 104% LDT Voltage Control - 1.2v Chip Set Voltage Control - 1.6v DRAM Voltage Control - 2.6v DRAM Configuration Settings: DRAM Frequency Set - 180 9/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3 RAS# to CAS# delay (Trcd) - 3 Bus Clocks Min RAS# active time (Tras) - 8 Bus Clocks Row precharge time (Trp) - 3 Bus Clocks Row Cycle time (Trc) - 9 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 3 Bus Clocks Write recovery time (Twr) - 3 Bus Clocks Write to Read delay (Twtr) - 2 Bus Clocks Read to Write delay (Trwt) - 3 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== 2x Prime95 + 3dMark2001SE + 2xCPU-Z + MBM + a64tweaker : 3dMark2003 : 3dMark2005 + Everest: ========== short description: 300x9=2700mhz 3-3-8-3-9-16 2.6vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now