eNforcer Posted May 3, 2006 Posted May 3, 2006 Where can I find the latest drivers online? I googled for the latest ULI drivers thing, is there anything else I need for the chipset? I'm lost. Also, sometimes I experience short pauses especially while playing music, and the Visualization (in bars mode with foobar) thing is really lagging with the music currently playing. Share this post Link to post Share on other sites More sharing options...
Guest eva2000 Posted May 3, 2006 Posted May 3, 2006 Just started playing with board and BH-5/UTT BH-5 ram - anyone notice even at 3.4v vdimm ram runs alot hotter on this board than DFI NF4 Ultra-D/SLI-D/SLI-DR series ? I'm talking like TCCD at 3.0v vdimm hot! Share this post Link to post Share on other sites More sharing options...
RGone Posted May 3, 2006 Posted May 3, 2006 Yes it seems so. RGone... Just started playing with board and BH-5/UTT BH-5 ram - anyone notice even at 3.4v vdimm ram runs alot hotter on this board than DFI NF4 Ultra-D/SLI-D/SLI-DR series ? I'm talking like TCCD at 3.0v vdimm hot! Share this post Link to post Share on other sites More sharing options...
Blacklash Posted May 4, 2006 Posted May 4, 2006 Will everyone have problems with a X-Fi? No. Problems have been well documented. Obviously, to each their own. Share this post Link to post Share on other sites More sharing options...
Guest eva2000 Posted May 4, 2006 Posted May 4, 2006 2x 512MB OCZ PC3200 Gold UTT BH-5 @255mhz 2-2-2-5 7-14-2223 at 3.4v vdimm Last night tested without the dual lcd thermal probes and only 2x40mm fans and modules would be scorching hot and test #5 would fail at 2nd to 4th loop with a handful of errors. Decided to put my dual lcd thermo probe to work and attached it to the side of each of my 2x 512MB OCZ PC3200 Gold UTT BH-5 and use a thermaltake 90+ cfm 120x25mm fan to blow directly on the modules instead of my 2x 40mm fans. Memtest86+ v1.65 5 loops of test #5 and temps already peak at Dimm 1 module = 37.5C Dimm 3 module = 32C So far up to 90+ loops and no errors unlike last night! Room temp between = 27.5C to 28.8C open desktop benching system setup. Conclusion, Dimm 1 slot is a hot bugger and that with even 3.4v vdimm you better have at least 90cfm of fan cooling on your modules to keep memory modules' temps in check for stability! Share this post Link to post Share on other sites More sharing options...
andyr(uk) Posted May 4, 2006 Posted May 4, 2006 Where can I find the latest drivers online? I googled for the latest ULI drivers thing, is there anything else I need for the chipset? I'm lost. Also, sometimes I experience short pauses especially while playing music, and the Visualization (in bars mode with foobar) thing is really lagging with the music currently playing. hi i got mine from the nvidia home page Share this post Link to post Share on other sites More sharing options...
ianmknight Posted May 4, 2006 Posted May 4, 2006 So I have a setup as in my sig, really nice opty 170 that oc's at 2.8 on stock, so not going to dump it or my RAM, but want to upgrade my MoBo. But want the following: 1. More PWMIC's as the 3 on this ultra D are running hot even with fans on them. 2. Dual disk RAID (SATA300 Not sure which disks yet) 3. ATI Graphics card as I use the dual screen HydraVision. 4 Good OC'ing MoBo as I think this Opty of mine has much more to offer. So recommendations please 1. Expert or CFX3200 ?. 2. ATI Graphic card's ? (not really into high performance gaming so don't need top of range, but really need dual Monitor for Hydravision. So a pair of single port cards or one dual port card.) 3. Pair of about 80gb to 160 Gb SATA disks for RAID'ing. (Raptors are just too expensive) Share this post Link to post Share on other sites More sharing options...
bmorgan98 Posted May 5, 2006 Posted May 5, 2006 Hello My 2 raptors are in good health but the system will still lockup for briefly 1-2 seconds and then resume ok and event viewer is reporting both paging error and time out on the uli raid device "An error was detected on device DeviceHarddisk0D during a paging operation. " "The device, DeviceScsim52881, did not respond within the timeout period." I wonder if the uli raid has a compatibility issue with western digital hard drives? Is anyone else having issues with the uli raid? Edit: Maybe i should start fresh raid and change the stripe size from 16 to 64-128k? Share this post Link to post Share on other sites More sharing options...
Guest eva2000 Posted May 5, 2006 Posted May 5, 2006 I've only had my CFX3200-DR for about ~24hrs but so far results look promising http://i4memory.com/showthread.php?t=2629 with alot of tips and tweaks from Tony at OCZ it has helped speed up the learning curve - which is very steep due to the amount of bios settings to tweak! i.e. 2x 512MB Corsair XMS3500C2v1.1 BH-5 Click on image for the larger full picture. ============================== 10x300HTT = 3000mhz @250mhz 2-2-2-5 7-14-2222 at 3.44v FSB Bus Frequency: 300 LDT/FSB Frequency Ratio: 4x (tried 5x but system didn't boot even with NMOS/PMOS drive strength @31 so dropped it to 4x) CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: High HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 5 CPU HT Bus Drive Strength: Strong K8 Cool & Quiet Support: Disabled CPU VID Control: 1.5v (set higher due to low vcore + high vdimm issue) CPU VID Special Control: AUTO DRAM Voltage Control: 3.44v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 166 CPC: Enabled CAS (tCL): 2 tRCP: 2 tRAS: 5 tRP: 2 tRC: 7 tRFC: 14 tRRD: 2 tRW: 2 tRTW: 2 tWTR: 2 tREF: 4708 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: AUTO DQS Skew Value: N/A DRAM Drive Strength: 3 (weak) DRAM Data Drive Strength: 2 (-33%) DIMM 1/2 Clock Timing Skew: AUTO DIMM 3/4 Clock Timing Skew: 300ps delay Max Async Latency: 8ns Read Preamble Time: 5ns IdleCycle Limit: 16clks Dynamic Counter: Disabled R/W Queue Bypass: 16x Bypass Max: 7x Burst Length: 4 Super Pi v1.5 32M ============================== 10x300HTT = 3000mhz @250mhz 2-2-2-5 7-14-2222 at 3.44v FSB Bus Frequency: 300 LDT/FSB Frequency Ratio: 4x (tried 5x but system didn't boot even with NMOS/PMOS drive strength @31 so dropped it to 4x) CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: High HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 5 CPU HT Bus Drive Strength: Strong K8 Cool & Quiet Support: Disabled CPU VID Control: 1.5v (set higher due to low vcore + high vdimm issue) CPU VID Special Control: AUTO DRAM Voltage Control: 3.44v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 166 CPC: Enabled CAS (tCL): 2 tRCP: 2 tRAS: 5 tRP: 2 tRC: 7 tRFC: 14 tRRD: 2 tRW: 2 tRTW: 2 tWTR: 2 tREF: 4708 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: AUTO DQS Skew Value: N/A DRAM Drive Strength: 3 (weak) DRAM Data Drive Strength: 2 (-33%) DIMM 1/2 Clock Timing Skew: AUTO DIMM 3/4 Clock Timing Skew: 300ps delay Max Async Latency: 8ns Read Preamble Time: 5ns IdleCycle Limit: 16clks Dynamic Counter: Enabled R/W Queue Bypass: 16x Bypass Max: 7x Burst Length: 4 Super Pi v1.5 32M ============================== 10x300HTT = 3000mhz @250mhz 2-2-2-5 7-12-2212 at 3.44v FSB Bus Frequency: 300 LDT/FSB Frequency Ratio: 4x (tried 5x but system didn't boot even with NMOS/PMOS drive strength @31 so dropped it to 4x) CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: High HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 5 CPU HT Bus Drive Strength: Strong K8 Cool & Quiet Support: Disabled CPU VID Control: 1.5v (set higher due to low vcore + high vdimm issue) CPU VID Special Control: AUTO DRAM Voltage Control: 3.44v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 166 CPC: Enabled CAS (tCL): 2 tRCP: 2 tRAS: 5 tRP: 2 tRC: 7 tRFC: 12 tRRD: 2 tRW: 2 tRTW: 1 tWTR: 2 tREF: 4708 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: AUTO DQS Skew Value: N/A DRAM Drive Strength: 3 (weak) DRAM Data Drive Strength: 2 (-33%) DIMM 1/2 Clock Timing Skew: AUTO DIMM 3/4 Clock Timing Skew: 300ps delay Max Async Latency: 8ns Read Preamble Time: 5ns IdleCycle Limit: 16clks Dynamic Counter: Enabled R/W Queue Bypass: 16x Bypass Max: 7x Burst Length: 8 Super Pi v1.5 32M ============================== 10x300HTT = 3000mhz @250mhz 2-2-2-0 7-12-0211 at 3.44v Memtest86+ v1.65 bandwidth = 3006MB/s :cool: FSB Bus Frequency: 300 LDT/FSB Frequency Ratio: 4x (tried 5x but system didn't boot even with NMOS/PMOS drive strength @31 so dropped it to 4x) CPU/FSB Frequency Ratio: 10x RD580 HT PLL Speed: High HT Bus NMOS Drive Strength: 5 HT Bus PMOS Drive Strength: 5 HT Bus Receiver Impendence: 5 CPU HT Bus Drive Strength: Strong K8 Cool & Quiet Support: Disabled CPU VID Control: 1.5v (set higher due to low vcore + high vdimm issue) CPU VID Special Control: AUTO DRAM Voltage Control: 3.44v SB PCIE Voltage: 1.8v NB Analogue Voltage: 1.34v LDT Bus Voltage: 1.34v NB Core Voltage: 1.34v DRAM Frequency Set: 166 CPC: Enabled CAS (tCL): 2 tRCP: 2 tRAS: 0 tRP: 2 tRC: 7 tRFC: 12 tRRD: 0 tRW: 2 tRTW: 1 tWTR: 1 tREF: 4708 Bank Interleaved: Enabled Errata 94: Disabled Errata 123: AUTO Odd Divisor Correct: Disabled DQS Skew Control: AUTO DQS Skew Value: N/A DRAM Drive Strength: 3 (weak) DRAM Data Drive Strength: 2 (-33%) DIMM 1/2 Clock Timing Skew: AUTO DIMM 3/4 Clock Timing Skew: 150ps delay Max Async Latency: 8ns Read Preamble Time: 4.5ns IdleCycle Limit: 0clks Dynamic Counter: Enabled R/W Queue Bypass: 16x Bypass Max: 7x Burst Length: 8 Super Pi v1.5 32M The above 23min 59.297s time managed to beat my DFI NF4 Ultra-D time of 23min 59.641s. Everest Home: Read = 7,142 MB/s Write = 3,361 MB/s Latency = 36.2 ns Sandra 2005 Lite SR3 Buffered = 7,486 / 7,419 Unbuffered = 3,717 / 3,847 ============================== working on figuring out 10x315HTT right now with dividers - anyone got any tips for >300HTT on dividers ? Share this post Link to post Share on other sites More sharing options...
NonDecepticon Posted May 5, 2006 Posted May 5, 2006 OCZ Tony said there's some kind of issue with the ULi controller and RAID, he suspects driving strength is to blame (to the controller). I don't think there is a fix ATM, but I believe running the RAID on the 3114 controller, although less attractive, is doable in the meantime. Share this post Link to post Share on other sites More sharing options...
bmorgan98 Posted May 5, 2006 Posted May 5, 2006 OCZ Tony said there's some kind of issue with the ULi controller and RAID, he suspects driving strength is to blame (to the controller). I don't think there is a fix ATM, but I believe running the RAID on the 3114 controller, although less attractive, is doable in the meantime. Ahh thanks Mate Thought that it might be memory related but all my timmings are in manual with safe timmings very stable primed for 11.5 hrs and memtested for 29 passes, i'll try the sil image later. thanks Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted May 5, 2006 Posted May 5, 2006 the only problem I have had with RAID is using the Hitachi Feature Tool to enable SATA II features on my drives other than that, RAID-0 with 2x80GB SATA II drives works like a charm I'll be posting up a help/tut when I get around to it if your RAID is timing out, and you have the latest bios, then you probably have some instability as I have built RAID-0 on 4 different 2GB kits of memory and zero problems. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now