likewhoa Posted September 4, 2007 Posted September 4, 2007 kitfit1 i need to get my hands on a nice 175 too so i can join the race. Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted September 4, 2007 Posted September 4, 2007 kitfit1 i need to get my hands on a nice 175 too so i can join the race. Â When your ready likewhoa, let battle commence Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted September 4, 2007 Posted September 4, 2007 Meanwhile I'm chugging away at try #2 for 3.8GHz... temps are gettin' a little scary but apparently she likes it just fine. Highest Core Temp I've seen is 67C, lil' higher than before, but hey, if it can get past the 6 hour mark (where it failed at a slightly lower voltage) I'll be good to go I hope. Â Hopefully I'll be posting a new OCDB entry around 7PM tonight :-D Share this post Link to post Share on other sites More sharing options...
CPDMF Posted September 4, 2007 Posted September 4, 2007 My only hope for another AMD GGG entry rests on an Opteron 1210, a Biostar T-force and 2 X 512 Team Xtreem Dark DDR2 1066. Not the combination I would have hoped for but it's the only AMD setup I have that has a shot. Â @Charmed, hope your 3.8 run is successful. Should have my P5K today so I will start to push on mine and see where I end up. This Abit IP35 is not quite doing the job after 390FSB. Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted September 6, 2007 Posted September 6, 2007 Ok, had the Redlines in since yesterday at 300x10 ram on the 166 divider @250. They went straight to 250 at 3-3-6-2-1t with 2.6vdimm. I've Memtested them up to 270 with no errors, but with 2.7vdimm. So it looks like the memory will take me to 3.2g without any problems. What i could do with a bit of advice is, what sort of DDS, DDDS, Mal and Rp should i be setting above 250fsb. At 250 i have the following settings:DDS is set at 6 Â Share this post Link to post Share on other sites More sharing options...
sherbanater Posted September 10, 2007 Posted September 10, 2007 Thoughts and comments welcome... Â By sherbanater, shot with DSC-P73 at 2007-09-04 Â By sherbanater at 2007-09-09 Â By sherbanater at 2007-09-09 Â The fan speed is wack for some reason...any ideas Share this post Link to post Share on other sites More sharing options...
Guest drteming Posted September 10, 2007 Posted September 10, 2007 Thoughts and comments welcome... Â Looks good, now get an OCDB entry and get in the club. Share this post Link to post Share on other sites More sharing options...
ReelFiles Posted September 10, 2007 Posted September 10, 2007 sherbanater, the image rules state 800x600, that applies to portrait pics too, so get that lower than 800px X 600px please. Share this post Link to post Share on other sites More sharing options...
Capt Proton Posted September 10, 2007 Posted September 10, 2007 Ok, had the Redlines in since yesterday at 300x10 ram on the 166 divider @250. They went straight to 250 at 3-3-6-2-1t with 2.6vdimm. I've Memtested them up to 270 with no errors, but with 2.7vdimm. So it looks like the memory will take me to 3.2g without any problems. What i could do with a bit of advice is, what sort of DDS, DDDS, Mal and Rp should i be setting above 250fsb. At 250 i have the following settings:DDS is set at 6 I believe those are Micron chips? If so, I would suggest FSB Bus Frequency............................. 300 MHz  DRAM Voltage ................................. 2.60V   Memclock (DRAM Frequency) .................... 166 1T/2T Timing (Command Per Clock).............. 1T CAS Latency (Tcl)............................. 3T RAS# to CAS# delay (Trcd)..................... 3T Min RAS# active time (Tras)................... 8T Row precharge time (Trp)...................... 2T Row Cycle time (Trc).......................... 10T Row refresh cyc time (Trfc)................... 16T Row to Row delay (Trrd)....................... 3T Write recovery time (Twr)..................... 2T Write to Read delay (Twtr).................... 2T Read to Write delay (Trwt).................... 3T Refresh Period (Tref)......................... 3072 DRAM Bank Interleave.......................... Enabled  DQS Skew Control.............................. Auto DQS Skew Value................................ 0 DRAM Drive Strength........................... Normal 3 or 4 (Level 6 or 8) DRAM Data Drive Strength...................... Level 2 Max Async Latency............................. 8ns DRAM Response Time............................ Normal Read Preamble Time............................ 6ns IdleCycle Limit............................... 32 256 Dynamic Counter............................... Disable R/W Queue Bypass.............................. 16x Bypass Max.................................... 7x 32 Byte Granularity........................... Disable (4 Bursts)  I have used these settings to get my OCZ Plat EBs to 265MHZ. These settings are from the OCZ support site and they worked well. The red number is their recommendation. Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted September 10, 2007 Posted September 10, 2007 They are 991492 IC's. They are running an Orthos run at the same timmings i posted above at the moment, but at 282x11(3.1gig)which puts the ram at 258.5. Dynamic counter is off for the moment, but i had it on for a 2 hour orthos run yesterday, which went fine. So i think the secondary's that i have at the moment are fairly much at the right place for my rig. Thanks for the imput Capt, when i start going over 260 i'll keep your timmings in mind. Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted September 11, 2007 Posted September 11, 2007 Mowhahaha... The Ultras are coming, the Ultras are coming! ::looks at the boxes:: =-O they're here! See y'all later tonight with new scores and highlights LOL Share this post Link to post Share on other sites More sharing options...
likewhoa Posted September 11, 2007 Posted September 11, 2007 I might be scoring me an opty 165 CCB1E for some subzero fun. WATCH OUT! Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now