kitfit1 Posted December 23, 2007 Posted December 23, 2007 DFI LP UT P35-T2R (LP 35DB07 BIOS) Intel E6600 (L714A245) 2x1024 Crucial Ballistix 8500 X1900 XT-X@689/797, CAT 6.6 DRIVERS 2X36GB Western Digital Raptor 10,000RPM SATA hdd RAID 0 LITEON 832S DVD R/W Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater ========== [b]Genie BIOS Settings:[/b] [color=red] Genie BIOS Setting: Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 8 X - Target CPU Clock........................ - 4240 MHz CPU Clock................................. - 530 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/667 - Target DRAM Speed....................... - DDR2 1061 PCIE Clock................................ - 105 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled CPU Feature: Thermal Management Control................ - Disabled PPM(EIST) Mode............................ - Disabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Disabled Execute Disable Bit....................... - Disabled Virtualization Technology................. - Disabled Core Multi-Processing..................... - Enabled Voltage Setting: CPU VID Control........................... - 1.6V CPU VID Special Add....................... - 101.65% DRAM Voltage Control...................... - 2.23V SB 1.05V Voltage.......................... - 1.15V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.61V CPU VTT Voltage........................... - 1.58V Vcore Droop Control....................... - Disabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Weak GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 110 CPU GTL 0/2 REF Volt..................... - 110 North Bridge GTL REF Volt................. - 110 DRAM Timing: Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 4 RAS# to CAS# Delay (tRCD)................. - 4 RAS# Precharge (tRP)...................... - 4 Precharge delay (tRAS).................... - 12 All Precharge to ACT...................... - AUTO REF to ACT Delay (tRFC)................... - 24 Preformance LVL (Read delay).............. - AUTO MCH ODT Latencey.......................... - AUTO Write to PRE Delay (tWR).................. - AUTO Rank Write to Read (tWTR)................. - AUTO ACT to ACT Delay (tRRD)................... - AUTO Read to Write Delay (tRDWR)............... - AUTO Ranks Write to Write (tWRWR).............. - AUTO Ranks Read to Read (tRDRD)................ - AUTO Ranks Write to Read (tWRRD)............... - AUTO Read CAS# Precharge (tRTP)................ - AUTO All PRE to Refresh........................ - AUTO Clock Setting Fine Delay: Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[14] DIMM 2 Clock fine delay................... - Current[ 6] Ch1 Command fine delay.................... - Current[10] Ch1 Control fine delay.................... - Current[ 5] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[13] DIMM 4 Clock fine delay................... - Current[ 5] Ch2 Command fine delay.................... - Current[10] Ch2 Control fine delay.................... - Current[ 4] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto Read delay phase adjust: Channel 1 Phase 0 Pull-In................. - Auto Channel 1 Phase 1 Pull-In................. - Auto Channel 1 Phase 2 Pull-In................. - Auto Channel 1 Phase 3 Pull-In................. - Auto Channel 1 Phase 4 Pull-In................. - Auto Channel 2 Phase 0 Pull-In................. - Auto Channel 2 Phase 1 Pull-In................. - Auto Channel 2 Phase 2 Pull-In................. - Auto Channel 2 Phase 3 Pull-In................. - Auto Channel 2 Phase 4 Pull-In................. - Auto [/color] ========== Orthos + 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 530x8 @ 4240Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
Clawhammer Posted January 23, 2008 Posted January 23, 2008 Gigabyte GA-X38-DQ6, F6 BIOS Crucial 4GB (4 x 1GB) DDR2 800 PC-6400 Intel Core 2 Duo E2160 Conroe 1.8GHz 1MB L2 Saphire HD 3870 512Mb 256 bit 777/1126 8.451 drivers 3x Hitatchi Deskstar 160Gb Sata 2 8Mb cache - raid 0- LG 16x IDE DVD Writer Enermax Liberty 620W Power Supply Tuniq Tower * * ========== [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - turbo CPU Clock Ratio..................... - 9x CPU Host Clock Control.............. - Enabled CPU Host Frequency (Mhz)............ - 356 PCI Express Frequency (Mhz)......... - 100MHz C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - Manual Memory Frequency (Mhz).............. - 1068 DRAM Timing Selectable (SPD)........ - Manual CAS Latency Time.................... - 5 DRAM RAS# to CAS# Delay............. - 5 DRAM RAS# Precharge................. - 5 Precharge Delay (tRAS).............. - 15 ACT to ACT Delay (tRRD)............. - Auto Bank Write to READ Delay............ - Auto Write to Precharch Delay............ - Auto Refresh to ACT Delay................ - 42 Read to Precharge Delay............. - Auto Memory Performance Enhance.......... - Normal Command to #CS Delay___________ 2T System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - 0.40V PCI-E OverVoltage Control........... - Normal FSB OverVoltage Control............. - 0.15V (G)MCH OverVoltage Control.......... - 0.10V CPU Voltage Control................. - 1.575 Normal CPU Vcore.................... - 1.325v [/color] ========== 3D Mark01 + Orthos + CpuZ 3D Mark03 + Everest read 3D Mark05 + Vista experiance 3D Mark06 + Superpi 1M Short description: 356x9 @ 3.2Ghz DDR2 1068 5-5-5-15 Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted February 1, 2008 Posted February 1, 2008 DFI LP UT P35-T2R (01/09/2008 Beta BIOS) Intel E8500 (Q740A493T) 2x1024 Crucial Ballistix 8500 8800 Ultra @ 710/1140, 169.21 Drivers 2X36GB Western Digital Raptor 10,000RPM SATA hdd RAID 0 LITEON 832S DVD R/W Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater ========== [b]Genie BIOS Settings:[/b] [color=red] Genie BIOS Setting: Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 9.5 X CPU-N2 Ratio.............................. - Enabled - Target CPU Clock........................ - 4607 MHz CPU Clock................................. - 485 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/667 - Target DRAM Speed....................... - DDR2 971 PCIE Clock................................ - 100 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled CPU Feature: Thermal Management Control................ - Disabled PPM(EIST) Mode............................ - Enabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Disabled Execute Disable Bit....................... - Disabled Virtualization Technology................. - Disabled Core Multi-Processing..................... - Enabled Voltage Setting: CPU VID Control........................... - 1.43570V CPU VID Special Add....................... - 101.88% DRAM Voltage Control...................... - 2.19V SB 1.05V Voltage.......................... - 1.15V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.41V CPU VTT Voltage........................... - 1.10V Vcore Droop Control....................... - Disabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Weak GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 65 CPU GTL 0/2 REF Volt..................... - 65 North Bridge GTL REF Volt................. - 65 DRAM Timing: Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 4 RAS# to CAS# Delay (tRCD)................. - 4 RAS# Precharge (tRP)...................... - 4 Precharge delay (tRAS).................... - 12 All Precharge to ACT...................... - AUTO REF to ACT Delay (tRFC)................... - 24 Preformance LVL (Read delay).............. - AUTO MCH ODT Latencey.......................... - AUTO Write to PRE Delay (tWR).................. - AUTO Rank Write to Read (tWTR)................. - AUTO ACT to ACT Delay (tRRD)................... - AUTO Read to Write Delay (tRDWR)............... - AUTO Ranks Write to Write (tWRWR).............. - AUTO Ranks Read to Read (tRDRD)................ - AUTO Ranks Write to Read (tWRRD)............... - AUTO Read CAS# Precharge (tRTP)................ - AUTO All PRE to Refresh........................ - AUTO Clock Setting Fine Delay: Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[1486] DIMM 2 Clock fine delay................... - Current[ 612] Ch1 Command fine delay.................... - Current[1012] Ch1 Control fine delay.................... - Current[ 562] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[1337] DIMM 4 Clock fine delay................... - Current[ 524] Ch2 Command fine delay.................... - Current[1086] Ch2 Control fine delay.................... - Current[ 449] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto Read delay phase adjust: Channel 1 Phase 0 Pull-In................. - Auto Channel 1 Phase 1 Pull-In................. - Auto Channel 1 Phase 2 Pull-In................. - Auto Channel 1 Phase 3 Pull-In................. - Auto Channel 1 Phase 4 Pull-In................. - Auto Channel 2 Phase 0 Pull-In................. - Auto Channel 2 Phase 1 Pull-In................. - Auto Channel 2 Phase 2 Pull-In................. - Auto Channel 2 Phase 3 Pull-In................. - Auto Channel 2 Phase 4 Pull-In................. - Auto [/color] ========== Orthos + 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 485x9.5 @ 4607Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
jelly Posted February 7, 2008 Posted February 7, 2008 Abit IP35 Pro, V.10 BIOS OCZ DDR2 PC2-6400 Platnum Revistion 2 2GB (2 x 1GB) DDR2-800 (ATI CrossFire Certified) Intel Core 2 Duo E6750 Conroe 2.66GHz 4MB L2 ATI X1900XT @ 621/720 2 Seagate Barracuda 7200.10 120GB 7200 RPM 8MB Cache SATA 1.5Gb/s Hard Drive RAID0 Lite-on 20x DVD-RW drive Hyper Type-R 580w Zalman 9700LED ========== [color=blue][b][size=4]µGuru Utility[/color][/b][/size] [color=green] CPU Operating Speed 2666 (333) External Clock...................... - 400MHz Multiplier Factor................... - X8 Esrimate New CPU Clock.............. - 3200MHz Dram Speed (cpu : Dram) Default..... - (DDR2 - 800) Pci Express Clock................... - 100MHz [color=blue][b][size=4]Voltage Control[/color][/b][/size] CPU Core Voltage.................... - 1.3500v DDR2 Voltage........................ - 2.100v CPU VTT 1.2v Voltage................ - 1.20v MCH 1.25v Voltage................... - 1.25v ICH 1.05v Voltage................... - 1.05v ICHIO 1.5v Voltage.................. - 1.50v DDR2 Reference Voltage.............. - 0% CPU GTLREF 0&2...................... - 67% CPU GTLREF 1&3...................... - 67% [color=blue][b][size=4]Advanced Chipset Features[/color][/b][/size] Cas Latency Time (tcL).............. - 4 Ras# to Cas# Delay (trcD)........... - 4 Ras# Precharge (tRP)................ - 4 Precharge Delay (tRAS).............. - 15 Refrech Cycle Time (tRFC)........... - auto Write Recovery Time (twR)........... - auto Write to Read Delay (tWTR).......... - auto Act To Act Time (tRRD).............. - auto Read ro Prechange (tRTP)............ - auto Command Rate........................ - 2T PCIe Complincy Mode................. - v1.0a Reg Force X1........................ - Disabled Init Display First.................. - PCIe X [/color] ========== Prime95+2xCPUZ+3DMarks01 3DMarks03 3Dmarks05 3DMarks06 Short description: 400x8 @ 3.20Ghz 4-4-4-15@2T Share this post Link to post Share on other sites More sharing options...
wevsspot Posted February 10, 2008 Posted February 10, 2008 Gigabyte GA-X38-DS4 (F2 01/02/08 bios) G.Skill F2-6400PHU1-1GBHZ 4X1gb Intel Core 2 Duo E8400 Wolfdale EVGA e-GeForce 8800 GTS 640MB @ 600/1402/900 WD Raptor 74X2 Raid0 WD SATA 250gb LiteOn DVD Opticals Corsair TX750W Swiftech Apex Ultra H20-220 [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Turbo CPU Clock Ratio..................... - 9x CPU Host Clock Control.............. - Enable CPU Host Frequency (Mhz)............ - 445 PCIe Frequency (Mhz)................ - Auto Performance Mode.................... - Turbo C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - 2.0d Memory Frequency (Mhz).............. - 950 DRAM Timing Selectable (SPD)........ - Manual CAS Latency Time.................... - 4 DRAM RAS# to CAS# Delay............. - 4 DRAM RAS# Precharge................. - 4 Precharge Delay (tRAS).............. - 12 ACT to ACT Delay (tRRD)............. - 6 Bank Write to READ Delay............ - 8 Write to Precharch Delay............ - 8 Refresh to ACT Delay................ - 40 Read to Precharge Delay............. - 6 Static tRead Value.................. - Auto Static tRead Phase Adjustment....... - Auto Clock & Skew Controls............... - all at defaults System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - +0.25 PCI-E OverVoltage Control........... - +0.30 FSB OverVoltage Control............. - Normal (G)MCH OverVoltage Control.......... - +0.100 MCH Reference Voltage Control....... - Normal DDR Reference Voltage Control....... - Normal DDR Termination Voltage Control..... - Normal GTL Ref1 Voltage Ratio.............. - Normal GTL Ref2 Voltage Ratio.............. - Normal Loadline Calibration................ - Enable CPU Voltage Control................. - 1.3000V Normal CPU Vcore.................... - 1.2200V [/color] ========== 3DMark01SE + Orthos + CpuZ 3DMark2003: 3DMark2005: 3DMark2006: AquaMark Short description: 445x9 @ 4.0GHz 4-4-4-12 Share this post Link to post Share on other sites More sharing options...
wevsspot Posted February 10, 2008 Posted February 10, 2008 Gigabyte GA-X38-DS4 (F2 01/02/08 bios) G.Skill F2-6400PHU1-1GBHZ 4X1gb Intel Core 2 Duo E8400 Wolfdale EVGA e-GeForce 8800 GTS 640MB @ 600/1402/900 WD Raptor 74X2 Raid0 WD SATA 250gb LiteOn DVD Opticals Corsair TX750W Swiftech Apex Ultra H20-220 [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Turbo CPU Clock Ratio..................... - 9x CPU Host Clock Control.............. - Enable CPU Host Frequency (Mhz)............ - 445 PCIe Frequency (Mhz)................ - Auto Performance Mode.................... - Turbo C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - 2.0d Memory Frequency (Mhz).............. - 950 DRAM Timing Selectable (SPD)........ - Manual CAS Latency Time.................... - 4 DRAM RAS# to CAS# Delay............. - 4 DRAM RAS# Precharge................. - 4 Precharge Delay (tRAS).............. - 12 ACT to ACT Delay (tRRD)............. - 6 Bank Write to READ Delay............ - 8 Write to Precharch Delay............ - 8 Refresh to ACT Delay................ - 40 Read to Precharge Delay............. - 6 Static tRead Value.................. - Auto Static tRead Phase Adjustment....... - Auto Clock & Skew Controls............... - all at defaults System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - +0.25 PCI-E OverVoltage Control........... - +0.30 FSB OverVoltage Control............. - Normal (G)MCH OverVoltage Control.......... - +0.100 MCH Reference Voltage Control....... - Normal DDR Reference Voltage Control....... - Normal DDR Termination Voltage Control..... - Normal GTL Ref1 Voltage Ratio.............. - Normal GTL Ref2 Voltage Ratio.............. - Normal Loadline Calibration................ - Enable CPU Voltage Control................. - 1.3000V Normal CPU Vcore.................... - 1.2200V [/color] ========== 3DMark01SE + Orthos + CpuZ 3DMark2003: 3DMark2005: 3DMark2006: AquaMark Short description: 445x9 @ 4.0GHz 4-4-4-12 Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted February 16, 2008 Posted February 16, 2008 EVGA 132-CK-NF78-A1 NVidia 780i SLI, P03 BIOS Mushkin 2x2GB DDR2-1066 XP2-8500 (996562) (OoP) Intel Core 2 Extreme QX6850 3GHz 8MB L2 eVGA 8800Ultra Superclocked 768MB 384-Bit GDDR3 PCI-E 16x (Stock@655MHz Core/1665MHz Shader/1125Mhz Mem) 171.16 drivers Western Digital Caviar SE WD3200YS 320GB 7200 RPM 8MB Cache SATA 3.0Gb/s & Western Digital Caviar SE WD5000AAKS 500GB 7200RPM 8MB Cache SATA 3.0 Gb/s HP dvd1040 External DVD+/-RW Drive Ultra X3 1600 Watt Modular Power Supply (+12V ~ 117A) DangerDen TDX775+Black Ice XtremeIII+Laing D5 Pump Cooling w/MCT-40 Coolant ========== [b]FSB & Memory Config[/b] CPU Freq, Mhz....................... - 3800.0 CPU Multiplier...................... - 9x FSB - Memory Clock Mode............. - Linked FSB - Memory Ratio ................. - Sync Mode FSB - QDR (Mhz)..................... - 1689 MEM (DDR), Mhz...................... - 844.5 [b]Memory Timing Setting[/b] Memopry Timing Setting.............. - Expert tCL (CAS Latency)................... - 4 tRCD................................ - 4 tRP................................. - 4 tRAS................................ - 12 Command Per Clock (CMD)............. - 2T tRRD................................ - Auto (4) tRC................................. - Auto (26) tWR................................. - Auto (6) tWTR................................ - Auto (9-10) (Varies between boots) tREF................................ - Auto (7.8uS) [b]System Clocks[/b] CPU Multiplier...................... - 9x PCIe x16_3 (Mhz).................... - Auto PCIe x16_2 (Mhz).................... - Auto PCIe x16_1 (Mhz).................... - Auto nForce SPP --> nForce MCP........... - 5 nForce SPP <-- nForce MCP........... - 5 [b]System Voltages[/b] CPU Core............................ - 1.4875v CPU FSB............................. - 1.5v Memory.............................. - 2.200v nForce SPP.......................... - 1.45v nForce MCP.......................... - 1.550v HT nForce SPP <-> MCP............... - 1.35v ========== Orthos (dual-prime95), 2x CPU-Z, 3dMark2001SE (65946): 3dMark2003: 47,423 3dMark2005: 21,824 3dMark2006: 15,704 Aquamark3: 195796 Short description: 422.25x9 @ 3.8Ghz 4-4-4-12-2T Share this post Link to post Share on other sites More sharing options...
Devil 07 Posted March 11, 2008 Posted March 11, 2008 DFI 975X/G Infinity, 2/27/2007 BIOS OCZ2P8002GK (2x1GB PC-6400 4-5-4-15) Intel Core 2 Quad Q6600 Revision G0 BFG 6600GT OC 1x WD 80GB IDE (OS) 1xSeagate 80GB SATA (Apps) 1x Seagate 400GB SATA (Samples) 1x Seagate 400GB SATA (Audio) Presonus FP-10 Firewire Audio Interface Samsung SE-S204 External DVD-RW drive PC Power & Cooling Silencer 610W * * * * ========== [b]Genie BIOS[/b] [color=red] Over Clock Mode Select.............. - Manual PPM Function........................ - Disabled CPU Clock Setting................... - 333Mhz PCIE Clock Setting.................. - 100MHz SATA Clock Sync. With............... - Fix 100Mhz CPU VID Offset Setting.............. - Default Default CPU Voltage................. - 1.28750v CPU VTT Voltage Setting............. - 1.20v DRAM Voltage Setting................ - 2.10v NB Chip Voltage Setting............. - 1.60v [/color] [b]DRAM Timing and Config[/b] [color=red] DRAM Timing Selectable.............. - Manual CAS Latency Time.................... - 4 DRAM RAS# to CAS# Delay............. - 5 DRAM RAS# Precharge................. - 4 Precharge Delay (tRAS).............. - 15 System Memory Frequency............. - 667Mhz Refresh Mode Select................. - 7.8 Write to Precharge Delay............ - Auto Write to Read Delay (Same).......... - Auto Write to Read Delay (Diff).......... - Auto Read to Write Delay................. - Auto Write Recovery...................... - Auto Read Recovery....................... - Auto Read Delay.......................... - Auto Data A Drive Strength............... - Auto Data B Drive Strength............... - Auto x8 Control Drive Strength........... - Auto x16 Control Drive Strength.......... - Auto x8 Clock Drive Strength............. - Auto x16 Clock Drive Strength............ - Auto Command A Drive Strength............ - Auto Command B Drive Strength............ - Auto [/color] ========== Multi-thread Prime95, 2x CPU-Z, 3dMark2001SE: http://img.photobucket.com/albums/v356/djr...Screenshot1.jpg 3dMark2003: http://img.photobucket.com/albums/v356/djr...Screenshot2.jpg 3dMark2005: http://img.photobucket.com/albums/v356/djr...Screenshot3.jpg 3dMark2006: http://img.photobucket.com/albums/v356/djr...Screenshot4.jpg Aquamark 3d: http://img.photobucket.com/albums/v356/djr...Screenshot5.jpg Short description: 333x9 @ 3.01Ghz 4-5-4-15 Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted March 15, 2008 Posted March 15, 2008 DFI LP UT P35-T2R (01/09/2008 Beta BIOS) Intel E8500 (Q740A493T) 2x1024 OCZ PC9600 FLEX (OCZ2FX12001G) 8800 Ultra @ 710/1140, 169.21 Drivers 2X36GB Raptor RAID 0 / 250GB Caviar LITEON 832S DVD R/W Pcp&P Turbocool 1Kw Mach2 GT/Chilly1/Desuperheater ========== [b]Genie BIOS Settings:[/b] [color=red] Genie BIOS Setting: Exit Setup shutdown....................... - Mode 2 CLOCK VCO divider......................... - Auto CPU Clock Ratio........................... - 9.0 X CPU-N2 Ratio.............................. - Disabled - Target CPU Clock........................ - 4610 MHz CPU Clock................................. - 512 MHz Boot Up Clock............................. - Auto DRAM Speed................................ - 333/800 - Target DRAM Speed....................... - DDR2 1230 PCIE Clock................................ - 100 MHz PCIE Slot Config.......................... - 1X 1X CPU Spread Spectrum....................... - Disabled PCIE Spread Spectrum...................... - Disabled SATA Spread Spectrum...................... - Disabled CPU Feature: Thermal Management Control................ - Enabled PPM(EIST) Mode............................ - Enabled Limit CPUID MaxVal........................ - Disabled C1E Function.............................. - Auto Execute Disable Bit....................... - Enabled Virtualization Technology................. - Disabled Core Multi-Processing..................... - Enabled Voltage Setting: CPU VID Control........................... - Auto CPU VID Special Add....................... - 127.87% DRAM Voltage Control...................... - 2.23V SB 1.05V Voltage.......................... - 1.15V SB Core/CPU PLL Voltage................... - 1.55V NB Core Voltage........................... - 1.53V CPU VTT Voltage........................... - 1.17V Vcore Droop Control....................... - Enabled Clockgen Voltage Control.................. - 3.45V GTL+ Buffers Strenght..................... - Strong Host Slew Rate............................ - Weak GTL REF Voltage Control................... - Enabled CPU GTL 1/3 REF Volt..................... - 68 CPU GTL 0/2 REF Volt..................... - 67 North Bridge GTL REF Volt................. - 69 DRAM Timing: Enhance Data transmitting................. - Fast Enhance Addressing........................ - Fast T2 Dispatch............................... - Auto CAS Latency Time (tCL).................... - 5 RAS# to CAS# Delay (tRCD)................. - 5 RAS# Precharge (tRP)...................... - 5 Precharge delay (tRAS).................... - 15 All Precharge to ACT...................... - 5 REF to ACT Delay (tRFC)................... - 35 Preformance LVL (Read delay).............. - 8 MCH ODT Latencey.......................... - AUTO Write to PRE Delay (tWR).................. - 13 Rank Write to Read (tWTR)................. - 11 ACT to ACT Delay (tRRD)................... - 3 Read to Write Delay (tRDWR)............... - 8 Ranks Write to Write (tWRWR).............. - AUTO Ranks Read to Read (tRDRD)................ - AUTO Ranks Write to Read (tWRRD)............... - AUTO Read CAS# Precharge (tRTP)................ - 3 All PRE to Refresh........................ - 5 Clock Setting Fine Delay: Ch1 Clock Crossing Setting................ - More Aggressive DIMM 1 Clock fine delay................... - Current[222] DIMM 2 Clock fine delay................... - Current[623] Ch1 Command fine delay.................... - Current[934] Ch1 Control fine delay.................... - Current[690] Ch2 Clock Crossing Setting................ - More Aggressive DIMM 3 Clock fine delay................... - Current[222] DIMM 4 Clock fine delay................... - Current[690] Ch2 Command fine delay.................... - Current[934] Ch2 Control fine delay.................... - Current[623] Ch1Ch2 CommonClock Setting................ - More Aggressive Ch1 RDCAS GNT-Chip Delay.................. - Auto Ch1 WRCAS GNT-Chip Delay.................. - Auto Ch1 Command to CS Delay................... - Auto Ch2 RDCAS GNT-Chip Delay.................. - Auto Ch2 WRCAS GNT-Chip Delay.................. - Auto Ch2 Command to CS Delay................... - Auto Read delay phase adjust: Channel 1 Phase 0 Pull-In................. - Enabled Channel 1 Phase 1 Pull-In................. - Enabled Channel 1 Phase 2 Pull-In................. - Enabled Channel 1 Phase 3 Pull-In................. - Enabled Channel 1 Phase 4 Pull-In................. - Enabled Channel 2 Phase 0 Pull-In................. - Enabled Channel 2 Phase 1 Pull-In................. - Enabled Channel 2 Phase 2 Pull-In................. - Enabled Channel 2 Phase 3 Pull-In................. - Enabled Channel 2 Phase 4 Pull-In................. - Enabled [/color] ========== Orthos + 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 512x9 @ 4610Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
Repr Posted April 6, 2008 Posted April 6, 2008 Asus Commando 1703-Beta (03/20/2008) Intel Core 2 Duo E8400 'Wolfdale' (Q747A477) 2x 1024 OCZ SLI-Ready Edition PC2-8500 (OCZ2N1066R2GK) EVGA GeForce 8800GT Superclocked (167.27 drivers) Seagate Barracudo 320gb 7200.10 Zalman CNPS9700 LED Corsair HX520 [b][color=blue]American Megatrends Inc. BIOS Settings:[/b][/color] [color=red] AI Tuning: Manual CPU Frequency: 525 DRAM Frequency: DDR2-1050MHz PCI Express Frequency: Auto PCI Clock Synchronization: Auto Spread Spectrum: Auto [color=blue][b]Over Voltage [/b][/color] CPU VCore Voltage: 1.4625 FSB Termination Voltage: 1.550V NB VCore: Auto Memory Voltage: 2.300V DDRII Channel A REF Voltage: DDRII_REF+10mv DDRII Channel B REF Voltage: DDRII_REF+10mv DDRII Controller REF Voltage: Auto SB Vcore (SATA, PCIE): Auto SB Chipset Voltage: Auto Asus C.G.I: Auto Static Read Control: Auto Configure Timing by SPD: Disabled DRAM CAS# Latency: 5 DRAM RAS# to CAS# Delay: 5 DRAM Clocks DRAM RAS# Precharge: 5 DRAM Clocks DRAM RAS# Activate to Precharge delay: 15 DRAM Clocks DRAM Write Recovery Time: 5 DRAM Clocks DRAM TRFC: 42 DRAM Clocks DRAM TRRD: 10 Rank Write to Read Delay: 10 Read to Precharge Delay: 10 Write to Precharge Delay: 11 [/color] Bios Orthos & 3dMark 01 3DMark 03 3DMark 05 3DMark 06 Aquamark 3 Short description 8x525 = 4200mhz 5-5-5-15@2t Share this post Link to post Share on other sites More sharing options...
red930 Posted April 20, 2008 Posted April 20, 2008 Gigabite p35 DS3R Intel E8200 "wolfsdale" intel core duo OCZ ddr2 pc2-6400 Gold kit, 4 gig. Samsung 250 GB SAT2 Peak Radeon HD 3850, 512MB TSST corp CDDVDW SH-S203W Fortron BlueStorm 500w [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=green] Robust Graphics Booster............. - Auto CPU Clock Ratio..................... - 8x CPU Host Clock Control.............. - Enabled CPU Host Frequency (Mhz)............ - 400 PCI Express Frequency (Mhz)......... - Auto Performance Enhancer................ - Turbo C.I.A.2............................. - Disabled System Memory Multiplier (SPD)...... - 2.0 Memory Frequency (Mhz).............. - 800 DRAM Timing Selectable (SPD)........ - Auto CAS Latency Time.................... - 5 DRAM RAS# to CAS# Delay............. - 5 DRAM RAS# Precharge................. - 5 Precharge Delay (tRAS).............. - 18 ACT to ACT Delay (tRRD)............. - 3 Bank Write to READ Delay............ - 3 Write to Precharch Delay............ - 6 Refresh to ACT Delay................ - 46 Read to Precharge Delay............. - 3 tRD................................. - 9 tRD Phase Adjustment................ - 0 System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - [+0.1] PCI-E OverVoltage Control........... - Normal FSB OverVoltage Control............. - [+0.1] (G)MCH OverVoltage Control.......... - [+0.1] CPU Voltage Control................. - Normal Normal CPU Vcore.................... - 1.22500V [/color] bios screen 1 bios screen 2 cpu-z, orthos 3d mark03 screen: 3d mark05 screen: Short decription 8 x 400 = 3.20 Ghz 5-5-5-18@2t Share this post Link to post Share on other sites More sharing options...
mknwatt Posted April 24, 2008 Posted April 24, 2008 GigaByte GA-P35-DS3L, F7 BIOS OCZ Platinum Revision 2 DDR2 800 (PC2-6400) 4G (4 x 1GB) OCZ2P800R22GK Intel Core 2 Duo E6300 Conroe 1.86GHz 2M shared L2 Cashe, MC-TDX BFG Tech GeForce 7600GT 256MB 128-bit GDDR3 @ 650/832 ~ NVIDIA 169.21 drivers, Zalman VF900 Western Digital Caviar SE WD1600JS 160GB 7200 RPM 8MB Cashe SATA 3.0Gb/s Lite On DVD Burner SHM-165H6S OCZ GameXStream OCZ700GXSSLI ATX12V 700W DD12V-D5 Pump – Black Ice GT Stealth 240 Rad. ============ [b]Advanced BIOS Features[/b] [color=red]CPU Multi-Threading................. - Enabled Limit CPUID Max. to 3............... - Disabled No-Execute Memory Protect........... - Enabled CPU Enhanced Halt (C1E)............. - Enabled CPU Thermal Monitor 2(TM2).......... - Enabled CPU EIST Function................... - Enabled Virtualization Technology........... - Enabled [/color] [b]MB Intelligent Tweaker (M.I.T.)[/b] [color=red]Robust Graphics Booster............. - Auto CPU Clock Ratio..................... - 7x CPU Host Clock Control.............. - Enabled CPU Host Frequency (Mhz)............ - 444 PCI Express Frequency (Mhz)......... - Auto C.I.A.2............................. - Disabled Performance Enhancer................ - Standard System Memory Multiplier (SPD)...... - 2.00 Memory Frequency (Mhz).............. - 888 DRAM Timing Selectable (SPD)........ - Manual CAS Latency Time.................... - 5 DRAM RAS# to CAS# Delay............. - 5 DRAM RAS# Precharge................. - 4 Precharge Delay (tRAS).............. - 14 ACT to ACT Delay (tRRD)............. - 3 Bank Write to READ Delay............ - 2 Write to Precharch Delay............ - 2 Refresh to ACT Delay................ - 36 Read to Precharge Delay............. - 2 tRD................................. - 8 tRD Phase Adjustment................ - 16 System Voltage Control.............. - Manual DDR2 OverVoltage Control............ - [+0.3v] PCI-E OverVoltage Control........... - Normal FSB OverVoltage Control............. - Normal (G)MCH OverVoltage Control.......... - [+0.1v] CPU Voltage Control................. - [1.3125v] Normal CPU Vcore.................... - 1.27500V [/color] ============ Prime 95, CPU-Z, GPU-Z, 3Dmark2001SE: 3Dmark03: 3Dmark05: 3Dmark06: shot description: 444 x 7 @ 3108 MHz ~ 1.3125Vcore 4Gig DDR2 888 MHz (5-5-4-14-2T) Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now