farksy Posted October 14, 2006 Posted October 14, 2006 Your max async has gotta be 8.0ns, the other time i tested UTTs, at 1:1 250Mhz MAL could be 7ns, but once i set it one 300HTT with a 166Mhz divider to run 250Mhz, MAL has to be at 8ns for stability. Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted October 14, 2006 Posted October 14, 2006 It's runnin' fine how it is :- lol  Just rebooted and set to this:  Genie BIOS Settings:  FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 101Mhz  CPU VID StartUp Value......................... - Auto  CPU VID Control............................... - 1.525V CPU VID Special Control....................... - + 104.8% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.59v DRAM Voltage Control.......................... - 2.87V  DRAM Configuration Settings:  DRAM Frequency Set............................ - 100=RAM/FSB:01/02 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 4708 Cycles DRAM Bank Interleave.......................... - Enabled  DQS Skew Control.............................. - Increase Skew DQS Skew Value................................ - 50 DRAM Drive Strength........................... - auto DRAM Data Drive Strength...................... - auto Max Async Latency............................. - 7ns DRAM Response Time............................ - fast Read Preamble Time............................ - 5ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts)  Booted right up and actually improved my boot time from 3 bars, to 2.5 bars LMAO Share this post Link to post Share on other sites More sharing options...
Thraxz Posted October 14, 2006 Posted October 14, 2006 Okay, it boots fast, now prove it'll stay that way (meaning no reinstall.) Share this post Link to post Share on other sites More sharing options...
CharmedLover84 Posted October 14, 2006 Posted October 14, 2006 Okay same settings but the ram is now running with a CAS of 2 Â gonna run AM3 then I'll set it to Prime and hope for the best... gotta say the RAM only running at 167x2 sucks but y'know what... for now, it'll work untiL I can get the OCZ replaced. Share this post Link to post Share on other sites More sharing options...
oc newbie Posted October 14, 2006 Posted October 14, 2006 Okay same settings but the ram is now running with a CAS of 2Â gonna run AM3 then I'll set it to Prime and hope for the best... gotta say the RAM only running at 167x2 sucks but y'know what... for now, it'll work untiL I can get the OCZ replaced. Sounds like you got yourself a good chip there, hopefully i'll see a new post in the ocdb in the morning. Share this post Link to post Share on other sites More sharing options...
smolt Posted October 14, 2006 Posted October 14, 2006 I have a OCDB entry ready for 2950 But I cant get 06 to work. can ya help me with 3Dmark 06? I have downloaded it 5 times and some down loads take 8 hours. every time I install it i get the same error Share this post Link to post Share on other sites More sharing options...
EdLSmith Posted October 14, 2006 Posted October 14, 2006 Share this post Link to post Share on other sites More sharing options...
EdLSmith Posted October 14, 2006 Posted October 14, 2006 http://s2.supload.com/free/Image_5-20061014100824.jpg/view Share this post Link to post Share on other sites More sharing options...
EdLSmith Posted October 14, 2006 Posted October 14, 2006 Here's my best for 1M: Share this post Link to post Share on other sites More sharing options...
Thraxz Posted October 14, 2006 Posted October 14, 2006 I have a OCDB entry ready for 2950 But I cant get 06 to work. can ya help me with 3Dmark 06? I have downloaded it 5 times and some down loads take 8 hours. every time I install it i get the same error  I wish I could help you but I'm as clueless as you are. Share this post Link to post Share on other sites More sharing options...
smolt Posted October 14, 2006 Posted October 14, 2006 I wish I could help you but I'm as clueless as you are. I googled it and said that (Management Instrument (WMI) services needed to be started in services but I cant even find the service ? Share this post Link to post Share on other sites More sharing options...
oc newbie Posted October 14, 2006 Posted October 14, 2006 It isn't listed as windows management instrumentation in the services tab? That is pretty weird didn't know that could be removed. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now