Clay Posted June 28, 2007 Posted June 28, 2007 DFI LANPARTY nF4 Ultra-D (6/04- BIOS) AMD XP4000+ San Deigo 2x512MB OCZ PC4800 Platnum (OCZ600512EEPE) XFX GeForce 7900GT, 552/1608 83.91 drivers 2X 74GB Western Digital Raptor2's 10,000RPM SATA hdd's Raid-0 Asus 16x DVD Ram burner OCZ 700GX * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 305 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - 1.400v CPU VID Control............................... - 1.175 CPU VID Special Control....................... - 123% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 15 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7weak DRAM Data Drive Strength...................... - level 1(reduced 50%) Max Async Latency............................. - 8ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 5ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: AquaMark3: ========== short description: 305x10 @ 3050Mhz, 1.44525Vid (Est) 2.5-4-8-3 @ 2.70v vdimm[/b Share this post Link to post Share on other sites More sharing options...
Fracture Posted June 29, 2007 Posted June 29, 2007 DFI LANPARTY nF4 Ultra-D (2006/04/06 BIOS) AMD X2 3800+ Toledo ADA3800DAA5CD LDBFE 0637BPMW 2x512MB Corsair 3500LL PRO (TWINX1024-3500LL PRO) Connect3D X850XP TE, 580/1256 Catalyst 7.3 drivers 320GB Seagate 7200RPM SATA HD ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 297 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - Auto CPU VID Special Control....................... - Above VID * 110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:9/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 6 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== CPU-Z Everest 3dmark2001SE Orthos 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 294x10 @ 2940Mhz, 1.44v (autox110%) 3-3-2-6 @ 2.60v vdimm 267mhz Share this post Link to post Share on other sites More sharing options...
gordesky1 Posted July 1, 2007 Posted July 1, 2007 DFI LanParty UT RDX200 CF-DR AMD Opteron 165 CCBBE 0616 2x 1gb A-DATA PC3200 Saphire x1900gt@ 546core and 729mem 2x Western Digital satas raid-0 psu Hiper 580watt cooler cool master gemin II ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 HT PLL High Speed............................. - enable LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - Auto CPU VID StartUp Value......................... - auto NB-SB Port Configuration...................... - Enhanced CPU VID Control............................... - 1.50 CPU VID Special Control....................... - Auto DRAM Voltage Control.......................... - 2.99v SB PCIE Voltage............................... - 1.9v NB Analog Voltage............................. - 1.2v LDT Bus Voltage............................... - 1.5v NB Core Voltage............................... - 1.2v [/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 120=RAM/FSB:03/05 Command Per Clock (CPC)....................... - enable CAS Latency Control (Tcl)..................... - 3.0 Bus Clocks RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks Min RAS# active time (Tras)................... - 04 Bus Clocks Row precharge time (Trp)...................... - 04 Bus Clocks Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 08 Bus Clocks Refresh Period (Tref)......................... - 4672 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - level 9 DRAM Data Drive Strength...................... - level 1 (reduce 505) Max Async Latency............................. - 12.0 ns Read Preamble Time............................ - 9.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 7 x 32 Byte Granularity........................... - Disable (8 Bursts) [/color] ========== http://img219.imageshack.us/img219/4305/oc1zf0.jpg http://img514.imageshack.us/img514/1033/oc2ym2.jpg http://img177.imageshack.us/img177/378/oc3jw5.jpg http://img244.imageshack.us/img244/4950/oc4hk7.jpg ========== short description: 334x9 @ 3006ghz, 1.520v 3.0-4-4-4 @ 2.99v vdimm Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted July 1, 2007 Posted July 1, 2007 DFI LANPARTY nF4 Ultra-D (04/06/06 BIOS) AMD OPTY 175 (CCBWE 0551VPMW) 2x512MB G-Skill PC4800 ( PN – 1GBFF-DDR600-1T ) X1900 XT-X@689/797, CAT 7.5 DRIVERS 2X36GB Western Digital Raptor RAID 0 LITEON 832S DVD R/W PCP&C 1KW PSU Mach2 GT/Chilly1 head/Desuperheater [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 289 LDT/FSB Frequency Ratio....................... - 4 CPU/FSB Frequency Ratio....................... - 11 PCI eXpress Frequency......................... - 105MHZ CPU VID StartUp Value......................... - STARTUP CPU VID Control............................... - 1.35v CPU VID Special Control....................... - 123% LDT Voltage Control........................... - 1.2v Chip Set Voltage Control...................... - 1.6v DRAM Voltage Control.......................... - 2.6v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 6 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 0 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 6 DRAM Data Drive Strength...................... - 4 Max Async Latency............................. - 8 DRAM Response Time............................ - fastest Read Preamble Time............................ - 5 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 289x11 @ 3179Mhz, Mach2 GT cooling Share this post Link to post Share on other sites More sharing options...
Guest navinjohnson Posted July 3, 2007 Posted July 3, 2007 DFI LanpartyUT nF4 Ultra-D (BIOS 2006/04/06) AMD Opteron 170 socket939 w/ Thermalright Ultra-90 (2750Mhz, 275x10) 2x1GB OCZ EL Platinum PC3200 XTC (OCZP4002GK) Evga GeForce 6600GT 128MB 128-bit PCI-E, 94.24 drivers, 400/1002 Seagate 160GB 7200RPM SATA hdd Pioneer 52x/16x DVD/CD-ROM PC Power & Cooling Turbo-Cool 470w Power Supply Thermaltake Soprano Case ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 280 LDT/FSB Frequency Ratio....................... - X3 CPU/FSB Frequency Ratio....................... - X10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.475 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 140=RAM/FSB:07/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 7 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 8 DRAM Data Drive Strength...................... - 1 Max Async Latency............................. - 7.0ns DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE + 2x CPUZ + SmartGuardian: http://i47.photobucket.com/albums/f161/Lib...Orthoscrop2.jpg 3dMark2003: 3dMark2005: 3dMark2006: Aquamark3.0 ========== short description: 280x10=2800mhz 1.475vcore 2.7vdimm 2-3-2-7 Share this post Link to post Share on other sites More sharing options...
werdwerdus Posted July 12, 2007 Posted July 12, 2007 DFI LANPARTY UT nF4 SLI-DR Expert (04/06/2006 BIOS) AMD X2 3800+ (LCBIE Toledo core) 2x1024MB OCZ PC4000 (OCZ5001024ELGEGXT) eVGA GeForce 7800GTX 256MB, 516/1330 94.24 drivers 2x Seagate Barracuda 7200.10 320GB SATAII (ST332060AS), 1x Western Digital 500GB 7200rpm SATAII (WDC WD5000AAKS-00TMA0), 1x Samsung Spinpoint 7200rpm SATAII (SP2004C) Plextor PX-716A DVDR Enermax 535w power supply (EG565P-VE) * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 315 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.525v CPU VID Control............................... - 1.525v CPU VID Special Control....................... - *107.2% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.77v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - Auto DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 07 DRAM Data Drive Strength...................... - Level 1(Reduce 50%) Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 ns IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE + CPU-Z (x2) + ITE Smartguardian: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark3: ========== short description: 315x9 @ 2835Mhz, 1.6v 3-4-3-8 @ 258Mhz, 2.72v 115+ hours Orthos stable Share this post Link to post Share on other sites More sharing options...
kitfit1 Posted July 13, 2007 Posted July 13, 2007 (edited) DFI LANPARTY nF4 Ultra-D (04/06/06 BIOS) AMD OPTY 175 (CCBWE 0551VPMW) 2x512MB G-Skill PC4800 + 2x512mb OCZ 4800 Platinum X1900 XT-X@689/797, CAT 6.6 DRIVERS 2X36GB Western Digital Raptor RAID 0 LITEON 832S DVD R/W PCP&C 1KW PSU Mach2 GT/Chilly1 head/Desuperheater [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 289 LDT/FSB Frequency Ratio....................... - 4 CPU/FSB Frequency Ratio....................... - 11 PCI eXpress Frequency......................... - 105MHZ CPU VID StartUp Value......................... - STARTUP CPU VID Control............................... - 1.35v CPU VID Special Control....................... - 123% LDT Voltage Control........................... - 1.3v Chip Set Voltage Control...................... - 1.6v DRAM Voltage Control.......................... - 2.8v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB Command Per Clock (CPC)....................... - Disabled CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7 DRAM Data Drive Strength...................... - 4 Max Async Latency............................. - 8 DRAM Response Time............................ - fast Read Preamble Time............................ - 5 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 289x11 @ 3179Mhz, Mach2 GT cooling Edited December 18, 2008 by kitfit1 Share this post Link to post Share on other sites More sharing options...
centy Posted July 19, 2007 Posted July 19, 2007 DFI LANPARTY nF4 SLI-D (704-2BT BIOS) AMD A64 3700+ San Diego KACAE 0546EPAW 2x1024MB G.Skill HX PC3200(DDR400) (F1-3200BIU2-2GBHX) Dell GeForce 6800, 400/1300 Forceware 92.91 drivers 250GB Seagate Baracuda 7200.8 7,200RPM SATA NCQ 8MB Cache hdd (ST3250823AS) NEC ND4550A DVD-RAM SuperMulti Drive 2MB Cache Tagan TG530-U15 530w ATX v2.01 Modular Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 311 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.325v CPU VID Special Control....................... - 113% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 0 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 1032 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Weak 4 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - 7.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 5.0 ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3DMark 2001SE + CPUZ 3DMark 03 3DMark 05 3DMark 06 Aquamark 3 ========== short description: 311 x 9 = 2799MHz, 1.46v 3-3-0-2 @ 2.70 vdimm Share this post Link to post Share on other sites More sharing options...
Syngensmyth Posted August 2, 2007 Posted August 2, 2007 DFI LANPARTY UT NF4 Ultra-D (04/06 BIOS) AMD 165 Opteron dual core CCBBE 0617FPMW w/Big Typhoon 2x1024MB G.SKILL F1-4000USU2-2GBHZ PC4000 (Samsung K4H510838C-UCCC) EVGA 7900gs 256, 500/690 94.24 drivers WD2500KS 250GB 7200 RPM SATA 3.0Gb/s RAID0 and 500GB Seagate Barracuda 7200.10 16mb 3GB SATA LITE-ON 16X DVD±R DVD Burner 12X DVD-RAM SATA OCZ 700 Game Xtreme ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 308 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.400v CPU VID Control............................... - Auto CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 9 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3684 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 8 DRAM Response Time............................ - Normal Read Preamble Time............................ - 5.5 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 308x9 @ 2772Mhz, 1.40v cpu voltages 3-4-8-4 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
robbay111 Posted August 30, 2007 Posted August 30, 2007 DFI LanParty UT NF4 Ultra-D AMD Athlon 64 X2 socket939 3800+ (2700Mhz, 270x10) 4x512MB Corsair 2Gb XMS3200 Xtreme Pro C2 Series (TWINX1024-3200C2PRO) ATI Radeon X800XL 256Mb PCI-E x16 ATI Display Drivers Western Digital Cavier SE16 SATAII-300 7200RPM 16Mb 250 GB Sony 16X DVD-ROM Corsair HX-620 (620w) Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 270 LDT/FSB Frequency Ratio....................... - x4 CPU/FSB Frequency Ratio....................... - x10 PCI eXpress Frequency......................... - 105MHZ CPU VID StartUp Value......................... - STARTUP CPU VID Control............................... - 1.55v CPU VID Special Control....................... - 100% LDT Voltage Control........................... - 1.2v Chip Set Voltage Control...................... - 1.5v DRAM Voltage Control.......................... - 2.8v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 140=RAM/FSB Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 3 Row precharge time (Trp)...................... - 7 Row Cycle time (Trc).......................... - 13 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Weak4 DRAM Data Drive Strength...................... - Level1 Max Async Latency............................. - 8 DRAM Response Time............................ - fast Read Preamble Time............................ - 5.5 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts) [/color] ========== Orthos + 3dMark2001SE + 2x CPU-Z: 3dMark2003: 3dMark2005: 3dMark2006: ========== short description: 270x10 @ 2700mhz - 1.55vcore (1.55v*100%) 3.0-3-3-7 @ 2.8vdimm Share this post Link to post Share on other sites More sharing options...
Guest LookBackX2 Posted October 3, 2007 Posted October 3, 2007 DFI LANPARTY CFX3200-DR (5/23/2006 Beta) AMD Opteron 170UP 2x1024MB TeamGroup Xtreem Cronus DDR500 EVGA 8800 GTS 320 Superclocked 3Ware 8506-4L PCI-X/PCI HD Controller, 3x Seagate Barracuda 320GB Raid 5 Samsung Writemaster DVD Burner w/Lightscribe CM Stacker 810 w/homebrew watercooling * * ========== [B]Genie BIOS Settings:[/B] [COLOR=red] FSB Bus Frequency............................. - 301 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 RD580 HT PLL Speed............................ - auto HT Bus MMOS Drive Strength.................... - 31 HT Bus PMOS Drive Strength.................... - 31 HT Bus Receiever Impedance.................... - 31 CPU HT Bus Drive Strength..................... - strong CPU VID Control............................... - 1.525v CPU VID Special Control....................... - Above VID * 102.3% DRAM Voltage Control.......................... - 2.65v SB PCIE Voltage............................... - 1.85v NB Analog Voltage............................. - 1.34v LDT Bus Voltage............................... - 1.34v NB Core Voltage............................... - 1.34v [/COLOR] [B]DRAM Configuration Settings:[/B] [COLOR=red] DRAM Frequency Set............................ - 166 Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 0 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Row refresh cyc time (Trfc)................... - 14 Row to Row delay (Trrd)....................... - 2 Write recovery time (Twr)..................... - 2 Write to Read delay (Twtr).................... - 2 Read to Write delay (Trwt).................... - 3 Refresh Period (Tref)......................... - 3120 DRAM Bank Interleave.......................... - Enabled Errata 94 Enhancement......................... - Disable Errata 123 Enhancement........................ - auto Odd Divisor Correct........................... - Disable DQS Skew Control.............................. - Increase DQS Skew Value................................ - 155 DRAM Drive Strength........................... - 9 DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) DIMM 1/3 Clock Timing Skew.................... - auto DIMM 2/4 Clock Timing Skew.................... - Delay 300ps Max Async Latency............................. - 8 Read Preamble Time............................ - 6 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 7 x Burst Length.................................. - 4 Bursts [/COLOR] ========== Prime95 + 3dMark2001SE + CPU-Z 1.35 + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark 3d: Everest Home Edition 2.20: ========== Share this post Link to post Share on other sites More sharing options...
Capt Proton Posted October 5, 2007 Posted October 5, 2007 DFI LANPARTY nF4 Ultra D (7/04-2BTA BIOS) Opteron 175 CCBBE 0617 2x1024MB OCZ PC4000 EB (OCZ5001024EBPE) EVGA 880GTS 640MB, 675/1024 163.44 drivers 3 X Barracuda SATA 7200.10 250GB RAID 0 Benq DW 1655 DVD OCZ GameXstream 600W * * * * ========== [Genie BIOS Settings:] FSB Bus Frequency............................. - 282 LDT/FSB Frequency Ratio....................... - 3X CPU/FSB Frequency Ratio....................... - 11X PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.475 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.6v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Normal 4 DRAM Data Drive Strength...................... - 2 Max Async Latency............................. - 8ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6ns IdleCycle Limit............................... - 32 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: (For some reason, the score isn't showing up on the screen. I had to upload to ORB to see the score) 3dMark 2006: ========== short description: 282 X 11 @ 3102Mhz, 1.475 cpu voltages 3-3-8-2 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now