RHKCommander959 Posted October 13, 2007 Posted October 13, 2007 yup. but thats why i suggested the foamies.... they compress if your not touching so that you can, and have enough springyness to help push it flat. Share this post Link to post Share on other sites More sharing options...
edjahman Posted October 13, 2007 Posted October 13, 2007 Im running orthos and my load temps are ~52 at 3006 ghz and 1.57vcore. How is that? Yes. It is a dual core. Look it up. I cant believe the difference. Wow. --EJM Share this post Link to post Share on other sites More sharing options...
RHKCommander959 Posted October 13, 2007 Posted October 13, 2007 pretty darn good musta got a good stepping. i cant get mine to do 3 stable with 1.65 yet, but it does 2.8 good, and 2.9 alright. Share this post Link to post Share on other sites More sharing options...
edjahman Posted October 13, 2007 Posted October 13, 2007 I bought it special from the old dfi street buy/sell forum. I forget the stepping and I dont know where the lid is. Its a good one for sure. Maybe ccbbe Share this post Link to post Share on other sites More sharing options...
RHKCommander959 Posted October 13, 2007 Posted October 13, 2007 i got mine to 3ghz today at 1.55 vcore but it wasnt bootable :/ mines not naked yet. i tried once but i wasnt getting much of the black stuff out Share this post Link to post Share on other sites More sharing options...
edjahman Posted October 14, 2007 Posted October 14, 2007 I know that the bolt through water blocks are the best but sometimes you have to work with what you have. I waited probably a year after everyone else to cut my lid off. It got me to 3 ghz. anyway. It was very easy. I have pics here. Bottom of page. http://www.flickr.com/photos/edjahman/page12/ A disposable razor is the way to go. Share this post Link to post Share on other sites More sharing options...
RHKCommander959 Posted October 14, 2007 Posted October 14, 2007 nice toe any old disposible razor? i looked at our cheap 'ens here but they dont look as though they're as wide... but maybe. i'll dismantle one and give it a shot Share this post Link to post Share on other sites More sharing options...
MACarter02 Posted October 14, 2007 Posted October 14, 2007 i hope those temps are degrees f :eek: Share this post Link to post Share on other sites More sharing options...
RHKCommander959 Posted October 14, 2007 Posted October 14, 2007 lol got it off thanks... it doest wanna start anymore, so i'll tinkner some more Share this post Link to post Share on other sites More sharing options...
wevsspot Posted October 16, 2007 Posted October 16, 2007 Here are some pics. of the standard way I install aftermarket heatsinks on AMD processors and socket939 motherboards that have the IHS removed. Share this post Link to post Share on other sites More sharing options...
RHKCommander959 Posted October 16, 2007 Posted October 16, 2007 not bad. mine works fine, a bit cooler. darn dfi boards are too sensitive though cause now the yellow and orange slot nearest the socket dont want to work. happened to another same model board too :/ oh well, i'm just gonna divvy the ram up between them and sell both in rigs for 750$ a piece Share this post Link to post Share on other sites More sharing options...
osen Posted October 17, 2007 Posted October 17, 2007 I disassembled a razor and got a blade from it, veeery thin, worked like a charm! Thanks for the tip. I took it very easy and the lid popped of my 165 I also lapped my Noctua NH-U12 as the base was pretty "ribbed?" and uneven. Here's the result: :tooth: Was it worth it? Hell yeah! Before, I was seeing ~50-53C load with only 1.475 and about 2850MHz. It wasn't stable much higher even with 1.5V and I couldn't give it more as I don't want to go much over 50C. Now, I began with setting it at 325x9(2925MHz) and 1.5V, booted up and ran orthos for a couple of hours, rock solid! And temps in SmartGuardian didn't exceed 41C (CoreTemp shows 46-48)! A drop of over 10C, with 0.25V more! Incredible, and the AS5 hasn't even set yet. This is in a P180, full with sound dampening material and only one 120mm intake and one blowing out in the back (Yate Loon's @ 900RPM) I'm now at 334x9(3006MHz) with 1.525V and load temp is about 44-45C (CoreTemp about 51-52C). Going to run orthos overnight but it seems to be rock stable. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now