newguy Posted August 12, 2005 Posted August 12, 2005 Just got them today, the OCZ people said just came in today. According to the staff said this RAM are so hot in the market now, because of the BF2 require 1.3-1.4GB in order to run smooth. So lots of people start grabbing them. And he said this SamSung RAM unlike other Gold series which require high voltage. At most just feed them with 2.9V, don't pump up to 3.0V. They can do 270MHz no problem for sure. And now, I just wonder if anybody know that which BIOS best fit this RAM cause I need to flash mine by using these and what is the timing for these sticks? Thank you. Share this post Link to post Share on other sites More sharing options...
BiBi Posted August 12, 2005 Posted August 12, 2005 sweeeeeet :dog: BF2 2GB for sure on high textures. no more pauses and stuttering. If you haven't already head over to the official OCZ forums, their staff should be able to help you with settings, bios, timings, voltages, etc. http://www.bleedinedge.com/forum/forumdisplay.php?f=45 Let us know how your 1:1 OC goes :shake: Share this post Link to post Share on other sites More sharing options...
stealth17 Posted August 12, 2005 Posted August 12, 2005 bump Share this post Link to post Share on other sites More sharing options...
newguy Posted August 16, 2005 Posted August 16, 2005 Hi, I flushed to 704-2BT BIOS, memory in orange slots, doing memtest for optimal settings TEST#5 passed for 3 hours (I didn't continue, looks like it was doing good so) but after applied timing from other forum at most I can reach 255MHz get into windows but memtest, super pi not stable. Sometimes when boot up will show CMOS Checksum error :sad: . Reboots itself after 255MHz. Here's my setting 255 x3 16 16 11 101 disable 1.450v auto x113% 1.30V 1.70V 2.90V Enable 200 enable 3 4 8 4 13 16 3 3 2 3 1032 auto enable auto 0 Level 8 Level 2 auto normal 6 256 disable 16 07 disable There is some strange thing happened after I flush to this BIOS, now the BIOS cannot save everytime, actually most of the time it won't save. but it should not acting like this, can I use other BIOS with this ram? :drool: Can anyone help me please? Thanks! Share this post Link to post Share on other sites More sharing options...
Speedyis300 Posted August 17, 2005 Posted August 17, 2005 You reset your bios after you flashed? Remove power cord, remove battery, move jumper for about 30-an hour?? I went from 704-3 to 704-2bt when i got these sticks, i have tehm at 264mhz(264x10) they are memtest stable and have had puter on for 24 hours, playing games or encoding dvd's and she is rock stable. Here are my settings, i acuatlly got these from Angry_Games sticky, tommorrwo i will test these vs my old settings to see if i find any difference.. Only thing you need to chnage is the cas setting..Put it to 3 DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Auto CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks(I think 10 is better for NF4) Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 19 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 04 Bus Clocks Refresh Period (Tref) - 2560 Cycles Write CAS Latency (Twcl) - 05 Bus Clocks DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 9.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) I think i fell in love with the picture of the girl in your signature.. :angel: Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted August 17, 2005 Posted August 17, 2005 in about 30-60 minutes I will be posting in the Overclocking database with this PC4000 2x1024 OCZ with my 4000+ @ 250x11 (2750Mhz) its on the last hour of prime then its easy 3d benchmarks. this is great memory, overclocks just as well on my 4400+ X2 Share this post Link to post Share on other sites More sharing options...
newguy Posted August 17, 2005 Posted August 17, 2005 Speedyis300, thanks for your info, I got BIOS problem, I put the clear CMOS jumper on till tonite to see I can clear them first then will try the timing tonite. Thanks for your comment, she is pretty eh? But no more, I have no idea where she are now? This morning show me this on my sig sig adjusted for size What to do??? Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now