Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by BiBi

  1. Hi I am trying to push my ram. OCZ 2x1GB Platinum pc3200 I switched to bios 704-2 and yellow slots after hearing good things about them. Tried each stick of ram in Yellow Slot1 and they ran fine at 220, but I get errors putting both in yellow slots. Using recommended settings from RyderOCZ I've heard ppl go to 230 with this ram but I can't get over 220. I know no OC is guaranteed but I just want to know if anything is limiting my OC.
  2. change your voltages in the bios....
  3. Hope I entered everything correctly my OCZ 2x1GB Platinum pc3200 won't go very high so I used the 3/4 dividers and kept the 2-3-5-2 timings.
  4. DFI LANPARTY UT NF4 ULTRA-D - 623-3 BIOS AMD Athlon 64 3000+ Venice OCZ EL PC3200 2GB 2X1GB DDR400 CL2-3-2-5 184PIN PIN DUAL CHANNEL MEMORY KIT /W RAMSINK SAPPHIRE RADEON X800 XL PCI-E 256MB DDR VIDEO CARD, 5.7 Catalyst Drivers - Stock SEAGATE BARRACUDA 7200.7 160GB SATA W/ NCQ 7200RPM 8MB 8.5MS HARD DRIVE BENQ DW1640 DVD +RW 16X8X16 -RW 16X6X16 DUAL LAYER +R 8X -R 4X BLACK IDE FORTRON FSP/SPI AX500-A 500W ATX12V 2.0 24PIN BLUE STORM POWER SUPPLY Thermalright XP-90 ALUMINUM HEATPIPE COOLER + PANAFLO 92MM HIGH SPEED COOLING FAN 2850RPM 56.8CFM 35DBA 3PIN NO SENSOR * * ========== Genie BIOS Settings: FSB Bus Frequency - 273 LDT/FSB Frequency Ration - x 3.0 CPU/FSB Frequency Ratio - x 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.300v CPU VID Special Control - Avove VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 150 (DRAM/FSB:3/4) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 13 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 0708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 2 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition 1.51: ========== short description: 273x9 @ 2457Mhz, 1.200v + 123% 2-3-5-2 1T 3:4 @ 2.7v
  5. have u read up on this 2GB kits round up yet? http://www.amdzone.com/modules.php?op=modl...rtid=163&page=1 Results of the OCZ pc4000 2GB check out RGONE's post and head over to the official OCZ forums. http://www.dfi-street.com/forum/showpost.p...536&postcount=4 http://www.bleedinedge.com/forum/forumdisplay.php?f=45 I have the OCZ 2GB Platinum kit pc3200 myself. still testing my ram peaks at ~220 =( on 3/4 divider my 3000+ peaks at ~290
  6. sweeeeeet :dog: BF2 2GB for sure on high textures. no more pauses and stuttering. If you haven't already head over to the official OCZ forums, their staff should be able to help you with settings, bios, timings, voltages, etc. http://www.bleedinedge.com/forum/forumdisplay.php?f=45 Let us know how your 1:1 OC goes :shake:
  7. DAYYYM sweet deal. you setup looks awesome now. nF4 :drool: nF3 :sad:
  8. BF2 does not require a high end CPU nor will it take advantage of dual core. It is however a memory hog. If you plan to run high textures on your video card you should have 2GB of ram to go along with it. That extra gig will eliminate any pauses and stuttering.
  9. You could also head over to OCZ's official forums. http://www.bleedinedge.com/forum/forumdisplay.php?f=45 Their employees can give you suggestions depending on your pricerange. They also won't sell you what you don't need.
  10. Read up on this 2x1GB kits roundup http://www.amdzone.com/modules.php?op=modl...rtid=163&page=1 I have the Platinum myself, it would give you the best stock settings with tight timings. But if you don't care about timings and want the cheapest what's wrong with OCZ Performance or Value?
  11. OCZ Value ? http://www.newegg.com/Product/Product.asp?...N82E16820146841
  12. Do I just set it in Task Manager to Realtime? or is there a setting in Prime?
  13. is the 9800 AGP???? you need a PCI-E with nF4 the retail boards usually come with 3/10 bios, it does officially Venice core. I have a 3000+ w/ Arctic Silver 5, XP-90 + Panaflo 92mm fan for cooling. Right now I have it OC'ed at ~2500mhz, load 39C, still testing for stability. Using dividers as my ram won't go up that high :drool:
  14. OC Forums Battlefield 2 not liking overclocked CPU Anyone here have any experience with overclocking/BF2/DFI nF4 ? I've gotten my rig on stock for a few days now, so I am ready to play with some OC.
  15. Great tool I just set this up thanks Soundx98!
  16. ya I found out about the 1floppy power connector after my purchase. I only use the floppy to flash but I can just use the CD. so it's not a problem :nod:
  17. What games will you be playing? I would seriously try to sell your current 6600GT AGP card. try the buy&sell here, http://www.redflagdeals.com/forums/ u might be able to find a local buyer. nF4 is just more future proof for any upgrades. I would get the Fortron BlueStorm 500W, it's one of the recommended PSUs in this forum. Just an alternative if the 520W PowerStream is too expensive and you want something better than the ModStream. If you play Battlefield 2, I would suggest you try to get 2GB of ram and a better video card. For BF2 you want a 6800GT or X800 XL if you are building a new system. Also 2GB of ram will help immensely for high textures and eliminate any pausing/stuttering. Check out this ram: OCZ 2x1GB pc3200 Platinum BF2 is VideoCard and Memory (ram & video memory) hog. Save money and get a 3000+ cpu instead, you can get that 200mhz of the CPU back with a moderate overclock. edit: what do you plan on doing with a SLi setup :confused:
  18. me <= Vancouver, Canada. getting my stuff from NCIX tomorrow. hopefully I won't be doing any RMAs :shake:
  19. Is it stuck at a black screen for a while? I've had that problem in a previous build.... never figured out why.... a reinstall of the OS fixed it.
  20. YES, these forums are great! I lurked around here for a week until making my purchase yesterday. Had several of AG's guides printed out :nod:
  21. Was going to get this board last week, but after reading this thread I went PCI-E with the LANParty UT nF4 Ultra-D.
  22. http://www.dfi-street.com/forum/showthread.php?t=6369 http://indabasement.com/DFINF4/bios/DFI_BIOSROM.rar
  • Create New...