CSS Junkie Posted May 2, 2005 Posted May 2, 2005 hey fellas i gots Corsair 3200XLPro - TwinX - 2 x 512MB sticks running currently @ 2-2-25/[email protected] (stock) I've been all the way upto 255 FSB no problem - thats DDR 510 @ 2.5-3-3-6/1T on my MSI Diamond board - darent push it further - PS - that was @ 2.75volts! :> However - exactly the same setup on my DFI SLI-DR has been succefully tested 1:1 @ 250FSB - Thats 500mhz DDR - I'm usually not into overclocking but when I saw the bandwidth increase - yeeehaaa! one liccle problem remains - Cant get this FX-53 to boot using the 10x mutiplier - I used to run 250FSB/500Mem/2500CPU on my Diamond board - but this DFI board refuses to let it get past post when using the 10x multiplier - x9 works fine - so does x11 (well, it posts @ least! but too much for my cpu @ 2750mhz) - my cpu can only do a tops of 2580 hmmm - will try a newer BIOS release once we gets an official one Well if you don't have at least the 3/10 bios you need to get it. I don't have the ram you have. I've had it at ddr470, but it wasnt stable at all. Like I said b4, it will not even run stable if I run it at 400. I may have gotten some bad sticks. I will say this though. I had this ram running on my MSI neo2k8n platium, and it would overclock ddr400 no problem. hmmmmmm. You just made me remember that. Maybe this board doesn't like this ram. I don't know. I've tried everything I can think of. Share this post Link to post Share on other sites More sharing options...
zoomee Posted May 3, 2005 Posted May 3, 2005 sorry forgot to add -i'm using Rgones recommended memory BIOS settings for overclocking - Memory is not the issue in my case - I know it can handle 250FSB no probs - as it works on the x9 multiplier - PS - running BIOS 3/10 performance i shall give the newer april BIOSes a try later this week :> Share this post Link to post Share on other sites More sharing options...
Sage2050 Posted May 4, 2005 Posted May 4, 2005 Sage, is there anyway you could give me a complete list of your bios settings. By that I mean your bios genie settings. Voltages and timings, you get the idea. If you could, I'd appreciate it. i'll get it asap. Share this post Link to post Share on other sites More sharing options...
Sage2050 Posted May 5, 2005 Posted May 5, 2005 everything not listed is set on Auto FSB - 250 LTD/FSB - x4.0 LTD Bus Transfer Width - d16 u16 PCI eXpress - 100mhz K8 Cool n quiet - diabled CPU startup - 1.425 CPU control - 1.425 CPU special control - 110% LDT voltage - 1.5v Chipset voltage - 1.8v DRAM voltage - 2.9v DRAM fequency - 180 (9:10) CPC - disabled CAS - 2.0 RAS to CAS delay - 02 min RAS drive - 05 Bank interleave - enabled DRAM drive strength - lvl 8 DRAM data drive strength - lvl 4 Max async 07.0 idlecycle - 256 dynamic counter - disabled R/W queue bypass - 16x bypass max - 07x granularity - diabled (8 bursts) Share this post Link to post Share on other sites More sharing options...
Sage2050 Posted May 6, 2005 Posted May 6, 2005 bump Share this post Link to post Share on other sites More sharing options...
PC1X1 Posted May 6, 2005 Posted May 6, 2005 I ordered the same ram XMS pro xL 3200, I ll post my results once rig is up, but on 2225 timings u should be around 210-220, dividers + looser timings should hit 240-250, again I;ll know more once the ram is on my hands and Ill mess with the bios. Share this post Link to post Share on other sites More sharing options...
Wired Posted May 7, 2005 Posted May 7, 2005 its C2. it would be nice if i could find a way to kill this ram, just to take advantage of the lifetime warranty =POoookkk...... ram guy? linkage please? http://www.asktheramguy.com, which is just a link to a sub-forum of http://www.houseofhelp.com. You guys may want to post the info in thislink in your post in addition to the info asked for in the first post in this thread: How To Read the Corsair Memory Label Corsair IC Inquiry Thread Post in that IC thread if you want to know which IC is used in your Corsair memory. FYI, the part #, version #, AND lot # are all needed for Ram Guy to find out which IC is in your memory. Only exceptions: 3500C2: BH-5 3200XL and 4400C25: TCCD Share this post Link to post Share on other sites More sharing options...
Sage2050 Posted May 8, 2005 Posted May 8, 2005 where do i find the part/version/lot numbers? well, i got part number from CPU-Z, but still need the other two. nevermind, missed that link. also, "thislink" is not linked to anything. Share this post Link to post Share on other sites More sharing options...
Robsmeister Posted May 9, 2005 Posted May 9, 2005 where can i find optimal bios settings for my corsair xms 3200 xl rev 1.2 memory at DFI NF4 ultra-d? Share this post Link to post Share on other sites More sharing options...
Vortexics Posted May 9, 2005 Posted May 9, 2005 ey guys I would like to OC at least a bit my winnie 3000 but I only have 1 stick of 512 MB Corsair Value Selected VS512MB400, and since i don't know how far will this memory go along with the oc. I would like to see some settings recommendations. FSB? ratio? LTD? DRAM Frequency? CAS? CPU vid? CPU volt? Chipset Volts? Share this post Link to post Share on other sites More sharing options...
dspayre Posted May 9, 2005 Posted May 9, 2005 ey guys I would like to OC at least a bit my winnie 3000 but I only have 1 stick of 512 MB Corsair Value Selected VS512MB400, and since i don't know how far will this memory go along with the oc. I would like to see some settings recommendations. Check out my setting in the Overclocking Database. http://www.dfi-street.com/forum/showthread.php?t=10195 Share this post Link to post Share on other sites More sharing options...
Vortexics Posted May 9, 2005 Posted May 9, 2005 ey what about the FSB you have a 3200 and I have a 3000 should I use 250x9 and LTD 3x? Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now