Drunky Posted March 27, 2006 Posted March 27, 2006 Thanks Clay if I come across some pc2100 at work I will save it for myslef!! As far as the chip goes whoever can get it to me the quickest will be fine so I will email Tmod and DFI!! Thanks man! Share this post Link to post Share on other sites More sharing options...
TheWizzard Posted March 28, 2006 Posted March 28, 2006 Yo drunky, I don't want to discourage you but you should take into consideration that all of our suggestions don't work at all. I've had the same problem with a lp-b which worked perfectly. All of a sudden the systems halts and wham, there they were, the 4-led's-of-death. Nothing helped. Hotflashing with another bioschip, replacing the bioschip with a complete new one and all the tips already given to you. Even at the technical service center they weren't able to fix this problem. Angry and another guy of dfi netherlands gave me a super special threatment. So i must say the DFI service is superb. So give the mailing to them a try before you open the window Share this post Link to post Share on other sites More sharing options...
Drunky Posted March 28, 2006 Posted March 28, 2006 I see thats cool I will contact DFI. I wasnt able to send a email to that dood but it got kicked back if someone could PM the addy to someone that can help me at DFI!! Thanks! Share this post Link to post Share on other sites More sharing options...
Clay Posted March 28, 2006 Posted March 28, 2006 PLEASE DO NOT POST OUR EMAIL ADDRESSES IN OPEN FORUMS. WE GET SPAM. WE DO NOT POST YOUR EMAIL ADDRESS IN OPEN FORUMS SO PLEASE RESPECT OURS. THIS IS A WARNING FROM THE ADMINS I'm sorry I wasn't thinkn' won't happen again! You could email "Angry" but you'll have to find his sig and click on it . It should be easy enough to find he's post sumptin' like 17000 times. Or look in the members list. I posted it. But I should have thought more about doing that . ^ ^(Sorry "Angry") Share this post Link to post Share on other sites More sharing options...
Drunky Posted April 11, 2006 Posted April 11, 2006 Alright guys I got my BIOS Chip in and put it in........and no worky worky unfortunaly! So I am not exactly sure what to do next!!!! I really just would like to get another board but no one sells them any more!! Can someone PM me a addy for someone at DFI that might be able to help me figure out how I can get this issue resolved! THanks guys for all the help and advice!! Share this post Link to post Share on other sites More sharing options...
red930 Posted April 11, 2006 Posted April 11, 2006 Angry's Public Profile.... http://www.dfi-street.com/forum/member.php?userid=2 Share this post Link to post Share on other sites More sharing options...
xerck Posted April 11, 2006 Posted April 11, 2006 i had the same situation before. this is that i do. i got another nf2 mobo and i did a hotflash to the plcc rom. to the dfi official bios rom. 28/7 date.. and the mobo revive. i try with all the dfi tricks. only the hotflash works for me.. trust me in my case i was dessesperate. and i was thinking buying another mobo. that was my oportunity.. if u had questions PM me. Share this post Link to post Share on other sites More sharing options...
delerious Posted May 15, 2006 Posted May 15, 2006 I just stumbled on this one, I'm in the same situation.. it's the kids's computer, lanparty A w/ barton 2500+, and was already using pc 2100 (sadly I ordered some pc3200 for it friday).. I have tried a different vid card, 1 stick of ram tried in all 3 slots, a stick of the pc3700 I used to use in it tried in all 3, removing the batteryw/ psu off for 30+ mins.. it's sitting on the desk with a different psu connected (old one had no p4 connector, this does) vid card in or out, no beeps.. just all 4 leds lighting @ once.. the CPU does produce heat.. no other reactions.. just left in in windoze last night and today it was a blank screen, so the first thing I did was pull the 100mhz jumper and it booted, I went straight into cmos to check voltages and temps, all seemed fine, so I exited bios, without saving I believe, then it didn't boot again..nothing for the next 8 hours of swapping everything but the CPU, clearing cmos over and over, 100mhz jumper on/off/on/off.. nothing but fans spinning and 4 instant LEDs.. even acts exactly the same with no CPU in it (though it is warming up).. will a bad CPU do this too? I don't want to buy another board and find it's the CPU.. if I'm replacing both my kids are going 64 bit! Share this post Link to post Share on other sites More sharing options...
Jaz_knos Posted May 19, 2006 Posted May 19, 2006 Lo All! New to the Fourms, Wish it were under better circumstances. I have a DFI LANParty NF2 B that has recently shown me those 4 lovely LED's of doom, and sod all else. Quote (From E-mail to DFI Tech Support in the Netherlands) " The problem started after a full (physical) clean of my system, in which all components were removed and cleaned with Isopropanol. Whilst out of the case all static sensitive components were placed on anti-static foam. After re-assembling my system in same hardware configuration as before the clean, it refused to boot correctly. It would begin the boot as far as "Initializing Super IO" according to the POST LED's and then hang there permanently. I tried using a minimal configuration of RAM, HDD and Graphics only but it still refused to boot. I have tried BIOS Resets, Long (overnight) BIOS Resets, running with minimal equipment etc all with no success. On the last attempt with minimal hardware all 4 POST LED's came on and remained on without any sign of response at all. Have inspected the board for any damage and none is obvious. Bought an ASRock K7NF2RAID Motherboard to run my system in the mean time. Suffered from random instability, resetting its self seemingly at random. Managed to install XP onto the blank HDD and after about 6 hours running stably it crashed out and has remained unresponsive since. Am concerned that in the process of breaking (or whatever it has done) it may have damaged one or more of my other components. All components are running at stock speeds for the board, and have never been overclocked. This exact hardware configuration has been working fine for me for about 12 months, and I have had the board since Aug 04 " So now you know whats happened, and I can say with some conficance that my MoBo is FUBAR at the moment. Not happy bout's it. Hopefully tech-support will be kind enough to send me a new BIOS chip out, and if not to do me an RMA on my board (phoned them and thats what they said so one does hope) I've only got 5 weeks left for RMA so I hope I get my answer one way or another quite quickly. Any Suggestions from anyone atall would be most appreciated. Best of luck to those of you who also have the LED's of doom.... Perhaps we should get some T-shirts for our club?! Jaz_knos Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now