BiBi

Hi I am trying to push my ram. OCZ 2x1GB Platinum pc3200 I switched to bios 704-2 and yellow slots after hearing good things about them. Tried each stick of ram in Yellow Slot1 and they ran fine at 220, but I get errors putting both in yellow slots. Using recommended settings from RyderOCZ I've heard ppl go to 230 with this ram but I can't get over 220. I know no OC is guaranteed but I just want to know if anything is limiting my OC.

loool

change your voltages in the bios....

Hope I entered everything correctly my OCZ 2x1GB Platinum pc3200 won't go very high so I used the 3/4 dividers and kept the 2-3-5-2 timings.

DFI LANPARTY UT NF4 ULTRA-D - 623-3 BIOS AMD Athlon 64 3000+ Venice OCZ EL PC3200 2GB 2X1GB DDR400 CL2-3-2-5 184PIN PIN DUAL CHANNEL MEMORY KIT /W RAMSINK SAPPHIRE RADEON X800 XL PCI-E 256MB DDR VIDEO CARD, 5.7 Catalyst Drivers - Stock SEAGATE BARRACUDA 7200.7 160GB SATA W/ NCQ 7200RPM 8MB 8.5MS HARD DRIVE BENQ DW1640 DVD +RW 16X8X16 -RW 16X6X16 DUAL LAYER +R 8X -R 4X BLACK IDE FORTRON FSP/SPI AX500-A 500W ATX12V 2.0 24PIN BLUE STORM POWER SUPPLY Thermalright XP-90 ALUMINUM HEATPIPE COOLER + PANAFLO 92MM HIGH SPEED COOLING FAN 2850RPM 56.8CFM 35DBA 3PIN NO SENSOR * * ========== Genie BIOS Settings: FSB Bus Frequency - 273 LDT/FSB Frequency Ration - x 3.0 CPU/FSB Frequency Ratio - x 9.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.450v CPU VID Control - 1.300v CPU VID Special Control - Avove VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 150 (DRAM/FSB:3/4) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 13 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 0708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 2 Max Async Latency - Auto Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: 3dMark2003: 3dMark2005: Aquamark 3d: Everest Home Edition 1.51: ========== short description: 273x9 @ 2457Mhz, 1.200v + 123% 2-3-5-2 1T 3:4 @ 2.7v

have u read up on this 2GB kits round up yet? http://www.amdzone.com/modules.php?op=modl...rtid=163&page=1 Results of the OCZ pc4000 2GB check out RGONE's post and head over to the official OCZ forums. http://www.dfi-street.com/forum/showpost.p...536&postcount=4 http://www.bleedinedge.com/forum/forumdisplay.php?f=45 I have the OCZ 2GB Platinum kit pc3200 myself. still testing my ram peaks at ~220 =( on 3/4 divider my 3000+ peaks at ~290

sweeeeeet :dog: BF2 2GB for sure on high textures. no more pauses and stuttering. If you haven't already head over to the official OCZ forums, their staff should be able to help you with settings, bios, timings, voltages, etc. http://www.bleedinedge.com/forum/forumdisplay.php?f=45 Let us know how your 1:1 OC goes :shake:

DAYYYM sweet deal. you setup looks awesome now. nF4 :drool: nF3 :sad:

BF2 does not require a high end CPU nor will it take advantage of dual core. It is however a memory hog. If you plan to run high textures on your video card you should have 2GB of ram to go along with it. That extra gig will eliminate any pauses and stuttering.

You could also head over to OCZ's official forums. http://www.bleedinedge.com/forum/forumdisplay.php?f=45 Their employees can give you suggestions depending on your pricerange. They also won't sell you what you don't need.

Read up on this 2x1GB kits roundup http://www.amdzone.com/modules.php?op=modl...rtid=163&page=1 I have the Platinum myself, it would give you the best stock settings with tight timings. But if you don't care about timings and want the cheapest what's wrong with OCZ Performance or Value?

OCZ Value ? http://www.newegg.com/Product/Product.asp?...N82E16820146841

:drool:

lol

Do I just set it in Task Manager to Realtime? or is there a setting in Prime?