Guest drteming Posted May 3, 2007 Posted May 3, 2007 DFI LANPARTY UT nF4 SLI-DR Expert (BIOS 04/06/06) Opteron 144 CAB1E 0614 BPBW 2x512MB Crucial Ballixtix Tracer (BL2KIT6464L505.16TG2Y) Sapphire X1950 GT, 675/1593 Catalyst 7.3 2x80GB Western Digital Caviar SE RAID-0 NEC Optiarc 7170A-0B DVD-RW Sunbeam NUUO 550W Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 351 LDT/FSB Frequency Ratio....................... - x 2.5 CPU/FSB Frequency Ratio....................... - x 9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.55v CPU VID Control............................... - 1.475v CPU VID Special Control....................... - 112% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.59v DRAM Voltage Control.......................... - 2.92v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 03 DRAM Data Drive Strength...................... - Level 01 Max Async Latency............................. - 9.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3DMark2001SE + CPU-Z: 3DMark03: 3DMark05: 3DMark06: AquaMark3: ========== short description: 351 x 9 @ 3159 MHz, 1.652v vcore 2.5-3-8-3 1T @ 263 MHz, 2.92v vdimm Share this post Link to post Share on other sites More sharing options...
Syngensmyth Posted May 5, 2007 Posted May 5, 2007 DFI LANPARTY nF4 SLI-DR Expert @ 2905MHz XP Pro 32-Bit DFI LANPARTY nF4 SLI-DR Expert (12/17/05 BIOS) AMD Athlon 64 3700+ San Diego (ADA3700AA5BN KABNE0544GPMW) 2x512MB OCZ EL DDR PC-4800 Platinum Elite Albatron Geforce 7800GT-SH PCI-E, 492/1188 84.21 drivers 2-74GB Raptors Raid-0 1-Maxtor DiamondMax 10 300GB Pioneer Black IDE DVR-110DBK Antec TruePower 2.0 550W ZALMAN CNPS9500 LED Cooler Master Wave Master ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 264 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 11 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 4.50 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.87v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 04 Min RAS# active time (Tras)................... - 10 Row precharge time (Trp)...................... - 04 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 5 DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 5.ons IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3dMark2001SE + CPU-Z 1.38: 3dMark2003: 3dMark2005: 3dMark 2006: AquaMark ========== short description: 264x11 @ 2905Mhz, 1.50 cpu voltages 3-4-10-4 @ 2.87v vdimm Share this post Link to post Share on other sites More sharing options...
Nightwish68 Posted May 12, 2007 Posted May 12, 2007 DFI LANPARTY nF4 SLI-DR Expert (06/04/06 BIOS) AMD X2 4200 Manchester LCB9E 0642XPMW 2x1280MB OCZ EL PC4000 Gold XTC (OCZ5002048ELGEGXT-K) EVGA 8800GTS 640MB, 575/1800 97.94 drivers 160GB Samsung SATA II hdd 200GB Samsung SATA II hdd 250GB Hitachi SATA II hdd Plextor PX-755A DVD Burner / Samsung SH-D162C DVD Player OCZ GameXStream 600W PSU Thermaltake Armor Black Case BIOS screenshots ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 290 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.350V CPU VID Special Control....................... - 102,4% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.56v DRAM Voltage Control.......................... - 2.71v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 9.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 Nano Seconds IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 4.00.976: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark: ========== short description: 290x10 @ 2900Mhz, 1.350 + 102,4% = 1.382V (CPU-Z 1.376V) 3-4-8-3 @ 2.71v vdimm Share this post Link to post Share on other sites More sharing options...
red930 Posted May 24, 2007 Posted May 24, 2007 DFI LANPARTY nF4 Ultra D(Bigtoe 623-2 tweaked / MemTest v1.65 Added By Tmod) AMD 3700+ (San Diego) KABZE ( lidless) Big Typhoon 2x512MB GAIL ONES PC48000 TccD XFX GeForce 7600GT, 650/1754 93.71 drivers 2x120GB Seagate Barracuda ST3120211AS SATA hdd NEC AD-7173A DVD±R Sharkoon SilentStorm 120 600 Watt Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 303 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 102Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.275 CPU VID Special Control....................... - 126% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.75v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:3/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2 RAS# to CAS# delay (Trcd)..................... - 2 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 11 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Normal 4 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 8 DRAM Response Time............................ - fastest Read Preamble Time............................ - 5 IdleCycle Limit............................... - 016 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 3dMark2003: 3dMark2005: 3dMark 2006: AquaMark3: ========== short description: 303x10 @ 3030 Mhz, 1275.126% 1.6 voltages 2-2-2-5 @ 2.75v vdimm Share this post Link to post Share on other sites More sharing options...
mungo Posted May 28, 2007 Posted May 28, 2007 DFI LANPARTY nF4 Ultra-D - Bios (04/06/06) AMD Opteron 165 CCBBE 0615EPMW 2x 1024 Crucial Ballistix Tracer PC4000 Evga 7900 GT KO 2x Hitatchi 80gb raid0. 2x Maxtor raid0 NEC DVD_RW OCZ 600W Gamexstream PSU Thermaltake TSunami Dream (Windowed) Swiftech Apogee GT Watercooled * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 322 LDT/FSB Frequency Ratio....................... - 2.5 CPU/FSB Frequency Ratio....................... - 9 PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.450v CPU VID Special Control....................... - 0 LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.68v (2.80v + dram .03v disabled)[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 7 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 17 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - normal L4 DRAM Data Drive Strength...................... - Weak Max Async Latency............................. - 8.0 NanoSeconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 7.0 NanoSeconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Dual Prime95 + 3dMark2001SE + CPU-Z + Everest Memory Latency: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 322 x 9 @ 2909MHz - 1.450v 3,3,3,7 1T @ 2.68v Share this post Link to post Share on other sites More sharing options...
Guest LookBackX2 Posted June 4, 2007 Posted June 4, 2007 DFI LANPARTY nF4 SLI-DR (7/04-2BTA BIOS) AMD Opteron 170(UP) 2x1024MB Team Xtreem Cronus ddr500, Micron 5b-f, 3330 2.72 vdimm EVGA 8800GTS 320MB , 612:1458/1008 153.22 drivers 2x320Gig Seagate Barracuda 7200.10, Raid 0 Config Dvd-R Drive OCZ GXT 600W * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 324 LDT/FSB Frequency Ratio....................... - x 3 CPU/FSB Frequency Ratio....................... - x 9 PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.45 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 0 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - weak 4 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 8 DRAM Response Time............................ - Normal Read Preamble Time............................ - 6 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos 8hr + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark: ========== short description: 324x9 @ 2915Mhz, 1.45 vcore 3-3-0-3 @ 2.72v vdimm Share this post Link to post Share on other sites More sharing options...
Guest LookBackX2 Posted June 4, 2007 Posted June 4, 2007 Mods please delete. Thanks Share this post Link to post Share on other sites More sharing options...
Clay Posted June 8, 2007 Posted June 8, 2007 DFI LANPARTY nF4 Ultra-D (6/23-2) Opteron 148 CACJE 0601VPBW 2x512MB OCZ PC4800 Platinum (OCZ600512EEPE) Evga 7900GT Co , 500/1500 91.04 Forceware drivers 2X74GB Western Digital Raptor 10,000RPM 8m cache SATA RAID=0 hdd 2X250Gb Seagate Barracudas 16mb cache Sata(Storage) Asus DL DVD Ram burner OCZ 700GX Genie BIOS Settings: FSB Bus Frequency............................. - 303 LDT/FSB Frequency Ratio....................... - 3X CPU/FSB Frequency Ratio....................... - 10x PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.425v CPU VID Control............................... - 1.2 CPU VID Special Control....................... - 133% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v DRAM Configuration Settings: DRAM Frequency Set............................- 200=RAM/FSB:01/01 Command Per Clock (CPC)..................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)....................- 4 Min RAS# active time (Tras).................. - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 15 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7weak DRAM Data Drive Strength...................... - level 1 (Reduded 50%) Max Async Latency............................. - 8ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 5ns IdleCycle Limit................................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max....................................... - 07 x 32 Byte Granularity............................. - Disable(4 Bursts) [/code] ========== Prime95 + 3dMark2001SE + CPU-Z 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 303x10 1-1 @ 3030Mhz, vid=1.2*133%=1.596 and 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
Guest Zoatebix Posted June 8, 2007 Posted June 8, 2007 DFI LANPARTY nF4 SLI-DR (04/06/2006 BIOS) AMD X2 3800+ dual core 2x1024MB Patriot PC3500LLK (PDC2G3500LLK) XFX GeForce 7800GT, 450/1050 93.71 drivers 200GB Western Digital CaviarSE WD2000JD 7,200RPM SATA hdd 80GB Hitachi Deskstar 7K80 7,200RPM SATA hdd BenQ DW1640 DVD+-RW Drive Seasonic S12 500w Power Supply Sound Blaster X-Fi XtremeMusic ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 280 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - x10 PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - Auto CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 07 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 14 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 0780 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Increase Skew DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) Max Async Latency............................. - 09.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 Nano Seconds IdleCycle Limit............................... - 016 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE + CPU-Z: 3dMark2003 + CPU-Z: 3dMark2005 + CPU-Z: 3dMark 2006 + CPU-Z: ========== short description: 280x10 @ 2800Mhz, Auto cpu voltages 3-3-7-2 @ 2.70v vdimm ========== Edit: As mentioned here, I accidentally clicked the Memory tab in my third CPU-Z window instead of the SPD tab. Here is the SPD information for my memory: Share this post Link to post Share on other sites More sharing options...
nYdGeo Posted June 11, 2007 Posted June 11, 2007 Good day! Since I'm stuck in dual-core AMD-ville until the end of the year, I just replaced my 4400X2 with the Opty 170 in my sig. I'm only using default voltage for the first couple weeks, heat-cycling for the first week for the AS5. I did a quick'n'dirty with Systool and got an error at 2831MHz, so I backed off to 2.75GHz and ran Orthos for about 3 hours. It was time for a cooling cycle, so I shut down then. For the Opty folks out there, is 2.75GHz decent for an Opty 170 at default voltage? If anyone is familiar with this stepping and has tested with it, can you tell me if I have a shot a 3GHz later, or is this a stepping that doesn't respond well to voltage, etc? Any info is much appreciated! Also, can anyone suggest a safe yet productive maximum core voltage for me to use based on the temps that I'm getting? Thanks again! You folks are a wealth of info! Share this post Link to post Share on other sites More sharing options...
rufuz Posted June 20, 2007 Posted June 20, 2007 DFI LANPARTY nF4 SLI-D (BIOS: 510-2FIX MemTest v1.65 Added By Tmod) AMD Athlon64 3200+ Winchester DH8-D0 on CoolerMaster air cooling 2x1024MB Corsair XMS (TWINX2048-3200C2PT) eVGA e-GeForce 7900 GTX Superclocked, 690/880 ("stock") nVidia drivers 93.71 2x 36GB Western Digital Raptor 10.000RPM SATA @ RAID-0 Pioneer DVR-108 DVD-RW OCZ ModStream 450w PSU ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 290 LDT/FSB Frequency Ratio....................... - X 3.0 CPU/FSB Frequency Ratio....................... - X 9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.500v CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150 (DRAM/FSB:3/04) (CPU/12) Command Per Clock (CPC)....................... - Disable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 10 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 18 Bus Clocks Row to Row delay (Trrd)....................... - 04 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Write CAS Latency (Twcl)...................... - Auto DRAM Bank Interleave.......................... - Disabled DQS Skew Control.............................. - Decrease Skew DQS Skew Value................................ - 50 DRAM Drive Strength........................... - Level 5 DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 08.0 Nano Seconds DRAM Response Time............................ - Fast Read Preamble Time............................ - 06.0 Nano Seconds IdleCycle Limit............................... - Auto Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3dMark2001SE (22475) + CPU-Z + OCCT: 3dMark2003 (22638): 3dMark2005 (10621): 3dMark 2006 (5406): ========== short description: 290x9 @ 2610Mhz, 1.5vcore 3-3-10-3 2T @ 217MHz, 2.8vdimm Share this post Link to post Share on other sites More sharing options...
AnUnknownSource Posted June 24, 2007 Posted June 24, 2007 DFI LANPARTY UT nF4 SLI-DR EXPERT (06/04/06 BIOS) AMD X2 4400+ Core:LCB9E Week:0635 Stepping:GPMW OCZ EL PLATINUM 2GB (2x1GB) DDR PC3200, MODEL OCZ4002048ELDCPE-K 2x FORSA 7900GTX IN SLI, 650/800 (STOCK) 160.03 BETA DRIVERS 6x120GB MAXTOR DIAMONDMAX 10 6L120M0 (1xSYS, 1xMISC, 4xDATA/GAMES IN RAID 1+0) CREATIVE SOUND BLASTER AUDIGY 2 ZS GAMER HAMA WIRELESS G PCI CARD PIONEER DVR-109 MULTI FORMAT DVD WRITER CORSAIR HX620W PSU WATERCOOLING:APOGEE CPU BLOCK, DD "DFI EXPERT" CHIPSET BLOCK, 2X KOOSAH GPU BLOCKS 120 SWIFTEC RAD, 240 X-FLOW RAD, 2x LAING D5 PUMPS * * ========== [B]Genie BIOS Settings:[/B] [COLOR=red] FSB Bus Frequency............................. - 273 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - 11x PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.425 CPU VID Special Control....................... - *107.2 LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.84v[/COLOR] [B]DRAM Configuration Settings:[/B] [COLOR=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enabled CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - Auto Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - Auto Write recovery time (Twr)..................... - Auto Write to Read delay (Twtr).................... - Auto Read to Write delay (Trwt).................... - Auto Refresh Period (Tref)......................... - Auto DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/COLOR] ========== Orthos + 3dMark2001SE + CPU-Z + MBM5 Temps: http://ocidb.com/albums/userpics/10017/primecpuzmbm1t.jpg 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 273x11 @ 3003Mhz, 1.425v *107.2% 3-3-8-3-1T @ 2.84v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now