gotdamojo06 Posted September 16, 2006 Posted September 16, 2006 Didnt know where to put this, but can you run wires under the motherboard, to help hide them? or will this short something out? Share this post Link to post Share on other sites More sharing options...
markiemrboo Posted September 16, 2006 Posted September 16, 2006 Bare exposed wire, no. Insulated wire... don't see why not... so long as there is a reasonable clearance between the motherboard tray and the motherboard (so the soldered pins on the back don't press up against the wires and go through the insulation!) Share this post Link to post Share on other sites More sharing options...
gotdamojo06 Posted September 16, 2006 Posted September 16, 2006 so you are saying that it could be done but it also could be risky Share this post Link to post Share on other sites More sharing options...
markiemrboo Posted September 16, 2006 Posted September 16, 2006 so you are saying that it could be done but it also could be risky I'm saying exactly what I said Should be fine if there's a reasonable clearance (and really there should be a pretty big clearance as you should be using stand off's!). I've run wires behind a motherboard before and, as you can see, I am still alive, and so is the motherboard. Share this post Link to post Share on other sites More sharing options...
computergee Posted September 16, 2006 Posted September 16, 2006 Yeah, you'll be fine as long as you dont pack them in there so the soldering points penetrate the insulation on the wire. I've done it before also. Share this post Link to post Share on other sites More sharing options...
romeo55 Posted September 16, 2006 Posted September 16, 2006 (edited) Yeah, you'll be fine as long as you dont pack them in there so the soldering points penetrate the insulation on the wire. I've done it before also. i did that when i tried running that annoying analog CD sound cable behind You can try it... but i don't reccomend it, the solder points might/will shread the wire Edited September 16, 2006 by The Unforgivin Share this post Link to post Share on other sites More sharing options...
fire_storm Posted September 16, 2006 Posted September 16, 2006 You should be ok seen people do it before in the case gallery before. Share this post Link to post Share on other sites More sharing options...
bigred Posted September 16, 2006 Posted September 16, 2006 there IS a trick to it. fiberglass weave electrical tape. it's strong enough to pin the wires down tight, and tough enough to keep the leads on the back of the mobo from punching thru. Share this post Link to post Share on other sites More sharing options...
bgnatewv2 Posted September 16, 2006 Posted September 16, 2006 (edited) Myself, I have pretty much always ran wires behind the mobo, on my rig and several others and I have never had a problem. The tape that bigred mentions is a very good idea and should reduce any chance of something happening. Edited September 16, 2006 by bgnatewv2 Share this post Link to post Share on other sites More sharing options...
Hyper Threaded Posted September 16, 2006 Posted September 16, 2006 Always depends on how thick the wire is, if it can't fit behind the mobo with reasonable clearance, don't shove it. Watch out for 3-pin fan connectors, they might even break the solder points on the back of the mobo if you try to push them. Wires that are just too stiff, don't try it. Basically, just use proper common sense. Don't go mad and let bad judgement break anything. Share this post Link to post Share on other sites More sharing options...
bigred Posted September 17, 2006 Posted September 17, 2006 you don't wad them under the board while it's installed... you lay them all out before you put the board in. tape em down, THEN mount the board Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now