Erosannin Posted April 28, 2012 Posted April 28, 2012 I'd like to know what's the max safe DRAM voltage for Sandy Bridge CPUs on an ASUS Maximus IV Extreme-Z Motherboard. Thank you guys P.S.: I know I am asking a lot of questions, but I just want to do it right as I was with a Nehalem processor and they were really heavy duty so little more DRAM voltage had no incidence on the CPU. Share this post Link to post Share on other sites More sharing options...
El_Capitan Posted April 29, 2012 Posted April 29, 2012 1.55V's is what Intel recommends. 1.65V's has been fine for many people on SB systems. Share this post Link to post Share on other sites More sharing options...
Erosannin Posted April 29, 2012 Posted April 29, 2012 OK but I wanna know if going over 1.65V is going to surely kill my CPU. Share this post Link to post Share on other sites More sharing options...
El_Capitan Posted April 29, 2012 Posted April 29, 2012 OK but I wanna know if going over 1.65V is going to surely kill my CPU. Why would you want to go over 1.65V's anyway? Share this post Link to post Share on other sites More sharing options...
Erosannin Posted April 29, 2012 Posted April 29, 2012 Overclocking the RAM itself why else? My RAM is some G.Skill 2133Mhz and the max available on the mobo settings is 2400Mhz Share this post Link to post Share on other sites More sharing options...
90sgamer Posted April 29, 2012 Posted April 29, 2012 Overclocking the RAM itself why else? My RAM is some G.Skill 2133Mhz and the max available on the mobo settings is 2400Mhz It would be a better idea to loosen the timings than overvolt to OC your RAM IMO Share this post Link to post Share on other sites More sharing options...
Erosannin Posted April 29, 2012 Posted April 29, 2012 Oki Doki I'll try that thank you Share this post Link to post Share on other sites More sharing options...
Erosannin Posted April 29, 2012 Posted April 29, 2012 normal timings for my RAM are 11-11-11-30 @ 2133Mhz 1.60V Do you have any rough Idea at the settings I can try for 2400Mhz? Share this post Link to post Share on other sites More sharing options...
ccokeman Posted April 29, 2012 Posted April 29, 2012 12-12-12 11-13-12 Loosen the TRFC and run memtest before booting into windows Share this post Link to post Share on other sites More sharing options...
Praz Posted April 29, 2012 Posted April 29, 2012 Why not buy some ram that will do the wanted speed without the increase in volts. Set ram voltage for the screenshot below is 1.55V. It is also available in 2x4GB kits. Share this post Link to post Share on other sites More sharing options...
Drdeath Posted April 29, 2012 Posted April 29, 2012 (edited) The key to degredation is keep the temps under max TCase. There is no real way to measure the Tcase (Temps in the middle of the processor). The Tcase temps are generally about 10 degress less than the core temps. That said, the max Tcase for SandyBridge is 68 so if your load temps stay at 75 or less thats good. Using high voltages like 1.45V or over requires good cooling (custom water). Many take it to 1.6V but as mentioned, keep the load temps under 75. The Dram voltage is your memory voltage and use your memory manufacturer specs which on DDR3 is usually 1.65V . 2400MHz will not give you better performance due to the timings. Lower frequency and tighter timings will trump 2400MHz. If you can get 2133MHz at cas 10 or cas 9 that would be optimal. If you can get 1866MHz at cas 8 that is the sweet spot for memory on SandyBridge. The chances you get 2400MHz is not gonna happen on a 2600K but possibly Ivybridge. SandyBridge E processors will get over 2400MHz. My top is 2452MHz on a 3930K. I see your runniong 2T on the command rate. 1T will get better performance also. After all this, I see your running Ivybridge... LOL. I haven't played with memory with Ivy yet but they say you can get higher frequencies with IvyBridge... Edited April 29, 2012 by Drdeath Share this post Link to post Share on other sites More sharing options...
MJCRO Posted April 29, 2012 Posted April 29, 2012 I've done 1.65v on my old SB system for months, never caused an issue. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now