t1no Posted December 23, 2006 Posted December 23, 2006 Good luck!! Share this post Link to post Share on other sites More sharing options...
otogrim Posted December 23, 2006 Posted December 23, 2006 Ok. Finally got a break from the christmas craziness.. lol. so here are my settings. FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - X3 CPU/FSB Frequency Ratio....................... - X9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.550v CPU VID Control............................... - 1.475 CPU VID Special Control....................... - 104% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.70v DRAM Voltage Control.......................... - 2.70v[/color] DRAM Configuration Settings: DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 16 Bus Clocks Row refresh cyc time (Trfc)................... - 18 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - normal4 DRAM Data Drive Strength...................... - level4 Max Async Latency............................. - 11ns DRAM Response Time............................ - fastest Read Preamble Time............................ - 7.0 IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) hope that helps. I'll put up some ss later on Share this post Link to post Share on other sites More sharing options...
mknwatt Posted December 23, 2006 Posted December 23, 2006 I tried a bunch of different voltage combo's and still I was unable to get it passed my current setting of 2943MHz - RAM on a 150 divider. I went a little crazy and tried 2970 @ 1.65V it ran dual p95 for 21mins, until I shut it down. I wasn't really wanting to ran at that voltage and my temps were hitting 53~54C. With the lower volts, <1.55 I could reach around 323~324*9 anything after that I had to give it over 1.6V. Share this post Link to post Share on other sites More sharing options...
THEnumber337 Posted December 24, 2006 Posted December 24, 2006 Just my 2 cents (sig)New system. Got my DFI yesterday, changed Htt*e, 300*9, and ram*150 and turned it on,,,Still installing software; so far so good. Did you go straight from stock to those settings? Share this post Link to post Share on other sites More sharing options...
mrelder Posted December 24, 2006 Posted December 24, 2006 Did you go straight from stock to those settings? No this is where i started out. I have been too busy installing software/playing to change anything. Maybe i'll change it up later; but for now im just enjoying it. I have the same ram as you (except 512x 2). I did try the 166 for the ram and it worked fine, but i didnt Prime it,,,so.... 2x512 OCZ Platinum EL 4001024ELDCPE-K Share this post Link to post Share on other sites More sharing options...
JCamaro Posted December 24, 2006 Posted December 24, 2006 Yeah.. I'm priming it right now while I'm at work , but after reading the rules, I should be running two instances of prime95 instead of orthos so I'm going to have to redo that later. Can't tell you the vcore off the top of my head but I'll let you know when I get home. I there a specific issue with orthos, It's what I use to test stability...Previously I did use the 2 instances of prime95 but orthos is easier to use and has a better interface. I'd just like to know if there is some disadvantage to using Orthos, or if it's just for an OCDB entry requiring 2 instances of Prime95 Thanks, JC Share this post Link to post Share on other sites More sharing options...
mknwatt Posted January 1, 2007 Posted January 1, 2007 There have been some changes to my CPU. Now it's nekid. My core temps have dropped 10C. I'm doing some testing and will see where it ends up. Was testing dual P95 at 334*9 1.61V, it ran for 31mins then core two failed. Temps were 48C, #1core 62C, #2core 66C. This is again an improvement since it would fail instantly before. We'll see were it ends up but I expect a better OC then this. :nod: Happy New Year Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now