xtw1ster Posted December 19, 2006 Posted December 19, 2006 You can.... give it some voltage and you'll likely see 3.1Ghz I don't think it's gonna happen. I tried 1.55 volts with 101.4%. Didn't boot. I'm wondering if it's the board. I can run solid at 2.75, anything more, is a no go. I lowered my multi to 8 and I could push fsb over 312; creating a lower cpu speed, but it worked. I compared to the opty165 database, and people are doing 2.9 on this one with water. Share this post Link to post Share on other sites More sharing options...
lunari Posted December 20, 2006 Posted December 20, 2006 Decided not to really push it just yet, sitting dual prime stable at 2.7Ghz, 1.34v. Share this post Link to post Share on other sites More sharing options...
Thraxz Posted December 20, 2006 Posted December 20, 2006 It takes AN AMAZINGLY HUGE amount of memory setting tweaking to really get much past 3.0Ghz with AMD. Though, cooling is big, you probably NEED water to get the kinda clocks I was talking about. Share this post Link to post Share on other sites More sharing options...
xtw1ster Posted December 20, 2006 Posted December 20, 2006 Finally hit 2.9Ghz, everything to auto except used auto and +101.4% on cpu voltage http://www.xanadu2.net/satan666/opty-2.9.png Share this post Link to post Share on other sites More sharing options...
ReelFiles Posted December 20, 2006 Posted December 20, 2006 What are your ambient temps and what does CoreTemp report? Which cooler are you using? Share this post Link to post Share on other sites More sharing options...
xtw1ster Posted December 20, 2006 Posted December 20, 2006 What are your ambient temps and what does CoreTemp report? Which cooler are you using? Room temp is about 20*C and I'm using a Thermaltake Big Typhoon with an Antec 2000 RPM 120mm fan instead of stock. Core Temp picture below http://www.xanadu2.net/satan666/core-temp.png Share this post Link to post Share on other sites More sharing options...
ReelFiles Posted December 20, 2006 Posted December 20, 2006 I was actually talking to lunari. Share this post Link to post Share on other sites More sharing options...
xtw1ster Posted December 20, 2006 Posted December 20, 2006 I was actually talking to lunari. sorry about that, but it would help if you quote the person you wish to respond to you Share this post Link to post Share on other sites More sharing options...
lunari Posted December 21, 2006 Posted December 21, 2006 Sitting rock solid stable at 2.8Ghz currently, still at 1.34v. Running a tuniq tower, 29c idle, 38c under dual prime load. Room temp is generally around 65-70f. I got it to boot into windows at 3.0Ghz at 1.4v or so, was stable enough for use, but would fail dual prime instantly. Edit: Can't do any SuperPI testing, because for some reason even at stock speeds it would BSOD on me. Edit #2: My CPU-Z validation at my stable 2.8Ghz/1.34v http://valid.x86-secret.com/show_oc.php?id=148421 Share this post Link to post Share on other sites More sharing options...
lunari Posted December 21, 2006 Posted December 21, 2006 Here are the OCDB style results I said I would post. I will update it as I download/install the programs. DFI LANPARTY UT nF4 SLI-DR (BIOS that was shipped on it.) AMD Opteron 165 dual core 2x1024MB G.Skill HZ Extreme PC-4000 eVGA 7900GTO, 685/1440: 93.71 Drivers 80GB WD 8MB Cache, SATA hdd Nu Technologies DVD+RW OCZ GameXstream 600w * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 312 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.375v CPU VID Control............................... - 1.375v CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 133=RAM/FSB:2/03 Command Per Clock (CPC)....................... - Auto CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 07 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 14 Bus Clocks Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: Coming Soon, 3dMark01, CPU-Z, Coming Soon 3dMark2003: 3dMark03 3dMark2005: 3dMark05 3dMark 2006: 3dMark06 ========== short description: 212x9 @ 2808Mhz, 1.375v BIOS/1.34v Actual, 3-3-3-7 @ 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
ReelFiles Posted December 21, 2006 Posted December 21, 2006 Nice temps, if that's read from CoreTemp. Share this post Link to post Share on other sites More sharing options...
xtw1ster Posted December 21, 2006 Posted December 21, 2006 Well folks here are my newest results. http://www.xanadu2.net/satan666/3dmark-3.0.png :eek2: Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now