xynder Posted May 25, 2006 Posted May 25, 2006 Just bought a new rig with the following specs: Opteron 165 CCBBE 0615 EPMW 2gb G-Skill DDR 500 DFI Lanparty Ultra-D This replaces my old AXP 1900+ with 512mb ram and a GF4 Anyways, I have a few questions. 1.) Does using an Opteron with a DFI board void either the CPU or motherboard warranty? Apparently they aren't approved for one another? 2.) Is there any way of AMD knowing if I am overclocking my CPU, for warranty purposes? 3.) Is there any way of AMD knowing if I am using an aftermarket HSF, for warranty purposes? 4.) Realistically, is there real danger in overclocking CPU/RAM? I am under the impression that if you go to high, the DFI board will just shut the computer off. Thanks guys! Share this post Link to post Share on other sites More sharing options...
Guest Kobalt Posted May 25, 2006 Posted May 25, 2006 Just make sure the DFI board has a fairly recent BIOS, and it should work just fine. 2) Burn marks would be a sign... 3) Depends what the HS is stuck on with, if thermal tape, and you got the same kind, then it wouldn't matter much. However, do note that opty's the retail version come with a very good heatsink! 4) if you apply to much voltage to RAM, you can fry it. DFI warns of this. Which is why they make you change a jumper. Share this post Link to post Share on other sites More sharing options...
wevsspot Posted May 25, 2006 Posted May 25, 2006 Just bought a new rig with the following specs: Opteron 165 CCBBE 0615 EPMW 2gb G-Skill DDR 500 DFI Lanparty Ultra-D This replaces my old AXP 1900+ with 512mb ram and a GF4 Anyways, I have a few questions. 1.) Does using an Opteron with a DFI board void either the CPU or motherboard warranty? Apparently they aren't approved for one another? 2.) Is there any way of AMD knowing if I am overclocking my CPU, for warranty purposes? 3.) Is there any way of AMD knowing if I am using an aftermarket HSF, for warranty purposes? 4.) Realistically, is there real danger in overclocking CPU/RAM? I am under the impression that if you go to high, the DFI board will just shut the computer off. Thanks guys! 1) There's no way they would know what cpu/board combination you used if you didn't tell them. 2) Overclocking usually requires more voltage, how much more depends on your board, your power supply and your particular cpu. Overclocking+voltage = more heat. So if you're cpu exhibited signs of excessive heat then AMD might not honor your warranty. 3) The TIM is on the cooler, so if for some reason you needed you could always throw the oem cooler on the cpu after the fact so it appeared it was used. 4) If you follow the NF4 overclocking guide you can minimize the chances that something goes wrong. Realistically there is ALWAYS a chance that something might break or fail earlier than anticipated when you are overclocking. MY own thoughts based on my character and ethics; If I fried my cpu or any other component in my rig because I was overvolting, overclocking or otherwise modifying my rig beyond manufacturer specifications, I wouldn't ever try and pull one over on AMD, DFI, OCZ whom ever. I understood the risks when I started down that road, and of course that's why I bought these components in the first place. Share this post Link to post Share on other sites More sharing options...
tasr Posted May 25, 2006 Posted May 25, 2006 xynder To DFI-Street. This is a great Opteron support thread. Socket 939 - Unofficial Opteron 939 Thread Honesty and integrity is your true answer. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now