Ciumka

Hey guys ok, so recently i noticed that my motherboard is not the same it used to be, why i checked my CPU & RAM on other mobos and they were working just fine, but on my mobo i cant overclock the way i used to. So i decide to get a new one, my question is which one would you prefer for socket 939 and yes it has to be DFI. What difference makes it if i have an ATI card so should i get ATI or NVIDIA bridge? thx

hey guys, ok i did run memtest for 2h and had 1error so i went and changed my ram timings to 3-3-6-2 and it worked. i'll probably run some more test tonight just to be sure. i'm just happy my rig is working because i wasnt looking to spent any money right now, anyway thx for help guys

THX David that helped, but i'm little confused why that would happen, i had this comp running like a champ for few months w/o any problems

Hey guys i really need someones help, i got back from work today i started my pc and boots fine. After 2minutes it freezes and it reboots itself. I tried to power it up but it only goes as far is BIOS boot and thats it. But now i have this ERROR MESSAGE TRAP 000000006==========EXCEPTION============ tr=0028 cr=0000011 cr2=00F0B009 cr3=0000000 gdt limit=o3ff base=00017000 idt limit=07FF base=00017400 cs:cip=0008:0040587 ss:esp=001000006d0e74 errcode=0000 flags=000100087 CyNoZr IntDis Down TrapDis does this look like my HD just went to heaven? or is it something else? can someone please give me some clues cause i'm lost. thanks

its probably OK, just use the link from above and you should be good

yes it is and its not that bad, gave small boost too

these are my settings with same RAM Genie BIOS Settings: FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - 2.5 CPU/FSB Frequency Ratio....................... - x 9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.55 CPU VID Control............................... - 1.400v CPU VID Special Control....................... - Above VID * 110 LDT Voltage Control........................... - 1.40v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.83v DRAM Configuration Settings: DRAM Frequency Set............................ - 150 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 06 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 10 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 8ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts)

try to put this: 3-3-6-2 and for now i would put the rest on auto to see if u can log on to windows. i had same problem with that ram since as a default it cames 3-3-8-2

:eek: how did i missed that :nod:

This is brand new RAM :nod: OCZ PC-4000 DUAL CHANNEL for any more info PM me or email at no emails allowed Price: $150 or best offer !!!

too much coffee today there Audio heheeh, just kidding. Anyway thanks for the answer and sometimes its quicker to ask quetion than just search.

Hey guys i just got one small (probably stupid) question - anyone has any idea what PWM IC in Smart Guardian means? :confused: thx

:cool: yup thx guys there is so many of them out there, thats why i'm taking my time going through all that. I just even realize that my case aint big enough for WC so i'm looking for that too. I wish i had more time, work is killing me : ( Later DFI's

oh, sry Angry, i wasnt sure where to post this

:drool: WELL, water cooling it is :nod: thanks guys, now the only thing left to do is to explain all that to my girlfriend (she always thinks i spent to much money on PC's) but hey its almost Christmas so who cares what she says, right heheeheh. I'm sure i'll have few more questions when i get all the parts but for now big thx.