Vapor Posted July 2, 2005 Posted July 2, 2005 ok sharp i will try that , now in bios under 32 Byte Granularity.............................Disable(8 Bursts) i only see enable 2 burst or disable 4 burst , is this because of my bios version is 615? Are you suer i should use 310 not 510-2? Share this post Link to post Share on other sites More sharing options...
Vapor Posted July 2, 2005 Posted July 2, 2005 Someone said it was a problem with the hd drivers dont use that disk???? is that my problem or ram? also sharp should i enable or disable external cache? and is it ok to use that disk driver that came with mb so i can combind my hdd's ? and what if i already have my ram in orange slots? Share this post Link to post Share on other sites More sharing options...
Sharp Posted July 2, 2005 Posted July 2, 2005 Hello, Go to 310 BIOS (it should say 8 bursts) Have external cache enabled Yes you can use the disk. Leave memory in orange slots Share this post Link to post Share on other sites More sharing options...
Vapor Posted July 2, 2005 Posted July 2, 2005 ok im picking my gf up and going home, sharp if u can get my pc working and installing windows i will send u 20$ just for the effort this means that much to me .... I know its not alot but rents due Share this post Link to post Share on other sites More sharing options...
Vapor Posted July 2, 2005 Posted July 2, 2005 sharp im going home now to try that seriously if u can get my pc to install windows and up and running i will send u $20 dollars, its not much but im kinda broke Share this post Link to post Share on other sites More sharing options...
col Posted July 2, 2005 Posted July 2, 2005 Hello, Remove BIOS 615 right now (it is not safe). Go to BIOS 310. Make sure you clear the CMOS for 10mins after the Flash. (PC off when you do this) Corsair modules = potential problem. Using the ORANGE slot after the BIOS flash, Set the memory voltage to 2.7v DRAM Frequency Set (MHZ).............200 (DRAM/FSB:1/01) Command per clock (CPC)...............Disabled Cas latency (tCL)...........................2 RAS to CAS delay (tRCD)..................3 Min RAS active time (tRAS)...............6 Row precharge time (tRP)..............3 Row cycle time (tRC)......................11 Row refresh cycle time(tRFC)..........14 Row to Row delay (tRRD).................3 Write recovery time (tWR)...............2 Write to read delay (tWTR)...............1 read to write delay (tRWT)...............1 Refresh period (tREF).......................AUTO Write CAS latency (tWCL)..................1 DRAM Bank Interleave............Enabled DQS Skew Control.............................Decrease Skew DQS Skew Value................................0 DRAM Drive Strength..........................AUTO DRAM Data Drive Strength..................AUTO Max Async Latency.............................6ns Read Preamble Time...........................5ns Idle Cycle Limit...................................AUTO Dynamic Counter................................Enable R/W Queue Bypass.............................AUTO Bypass Max.........................................AUTO 32 Byte Granularity.............................Disable(8 Bursts) See what happens. Run memtest for a few hours, 3 (8 it you have the time, you should make the time to do this) Thanks Sharp Those settings work well for me. Share this post Link to post Share on other sites More sharing options...
Sharp Posted July 2, 2005 Posted July 2, 2005 See if you can enable CPC, Share this post Link to post Share on other sites More sharing options...
Vapor Posted July 2, 2005 Posted July 2, 2005 Ok.... heres what i've done so far.... Flashed bios 310 , removed cmos and power for 10 mins, loaded optimal defaults, entered in sharps setup, one thing under my dram data strength there isnt an auto option only 1-4 so i put it at 3? Went into sata and enabled my sata 1 and 2 so f10 would show up . I go into windows and hit f6 like i was doing back on the other bios's 615 and default bios. When it asks me for a disk i put the sata drivers that came with mb in and hit enter all of a sudden for the first time it says "File txtsetup.oem cause an unexpected error (512) at line 1742 in c:xpclientbasebootsetupoemdisk.c." So i just skipped the driver and it shows hds as 2 seperate which i dont want... So i just go through formating and copying the files (which it didnt stop on that file i was having problems copying -IDECOI.DLL- before windows installation. Computer restarted and says boot from cd and if i hit enter it just goes through setup once again if i dont hit boot from cd it says NTLD error hit cntrl+alt+del which is because i dont have windows installed probably.... I dont know much about these satas so bare with me I restarted and went into bios and disabled external cache because it was something someone told me to disable so i did and restarted.. Went back into windows setup and tried f6 and install those raid drivers, and it let me ???? the harddrives were then back together 160gb (159.8 i think) started formating then copyed files and Bam same problem idecoi.dll cant be copyed sooo here i am..... Share this post Link to post Share on other sites More sharing options...
Vapor Posted July 3, 2005 Posted July 3, 2005 anyone? Share this post Link to post Share on other sites More sharing options...
Sharp Posted July 3, 2005 Posted July 3, 2005 Hello, try creating the raid disk again, on a different disk too. http://www.dfi.com.tw/Upload/Driver/NFORCE_R.exe Try this again with external cache enabled/disabled. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now