Kelt
Members-
Posts
13 -
Joined
-
Last visited
Kelt's Achievements
Newbie (1/14)
-
Hellfire's 6/19 Bios With 12/18 ROMSIP
Kelt replied to a topic in Processors, Motherboards and Memory
Managed to increase fsb beyond 250 at a voltage far lower than before (0.75v to be precise) also my system temp seems to have reduced, even though ambient is the same! I cant explain why...I'm just grateful ! just ran 3D2001 ..previous best was 20180 ....check this :-) http://service.futuremark.com/compare?2k1=8041008 -
Hellfire's 6/19 Bios With 12/18 ROMSIP
Kelt replied to a topic in Processors, Motherboards and Memory
Hi Hells, flashed your bios to my LPB and....what can I say.... THANK YOU :-)) -
06/19 Fixes Cold-Boot - Please post HERE!
Kelt replied to RGone's topic in Processors, Motherboards and Memory
Okay guys, I've got a few spare bios chips around the place so i'm gonna try flashing using Winflash. I'll let you know how it goes. -
ty RGone, My problem has been resolved, the answer may help others though. I removed Bios Saviour, put the new 11/27 chip directly into the bios socket...and...it worked!!! So now I have to figure out what is wrong with this Brand new programmed Bios Saviour. ~Kelt~
-
Update Ok, I've fitted a Bios Saviour, programmed to 11/27.Fitted a brand new bios chip, also programmed to 11/27. Removed the jumper on my single WD hard drive, and what do I get? 4 Led's on and not able to enter Bios. I've also tried another graphics card....same results any ideas guys? ~Kelt~
-
HELP with Lanparty NFII Ultra B needed
Kelt replied to Flagg's topic in Processors, Motherboards and Memory
Hi Flagg, I suggest you check out this link http://forums.pcper.com/printthread.php?t=319897 May answer a few of the questions you ask about hotflashing using a different motherboard. ~Kelt~ -
HELP with Lanparty NFII Ultra B needed
Kelt replied to Flagg's topic in Processors, Motherboards and Memory
Dude. the bottom line is :- 1)Get your bios chip to 11/27 2) before you insert the chip make sure Cmos is TOTALLY cleared ( ie J8 + remove battery + have 6 beers...ie ...leave it overnight) 3) Follow AG's flash bios advice 4) insert + pray your UK m8 ~Kelt~ -
HELP with Lanparty NFII Ultra B needed
Kelt replied to Flagg's topic in Processors, Motherboards and Memory
Hi Flagg, I must admit that you have me a bit confused. You say your board is a couple of weeks old? Well, all new boards (mine included) were shipped with the 11/27 bios version installed.I'm sure AG will confirm this.So, maybe you've given the board a problem trying to flash from 11/27 to 11/27, not sure, but hope you get it sorted. ~Kelt~ -
HELP with Lanparty NFII Ultra B needed
Kelt replied to Flagg's topic in Processors, Motherboards and Memory
Yep, tis no probs... Step 1 - Fire up the good board and get it to the point of being ready to flash bios. Step 2 - Remove bios from working board Step 3 - Insert dodgy bios chip Step 4 - Flash Step 5 - Remove bios chip Step 6 - Put original bios chip back again Step 7 - reboot Step 8 - Put the chip you have in yer hand back where it belongs! (advice given by Marci @ over-clock.co.uk) ~Kelt~ -
Sorry guys , the board was working before, it was not a new install. I had succesfully flashed bios to 12/31 in the past and was flashing to 2/17. Could it be possible that I have corrupted bios? I can get the chip hotflashed if you think that is the problem. Even with these minor problems, I still think this is the best board i've owned! Thanks ~Kelt
-
I put another BIOS chip in, got 4 led's on now, but still no post into BIOS, removed CD and DVD drives...still no post ~Kelt~
-
When I power up my system, it refuses to post. LED's 1&2 are on and #3 just keeps fickering on and off. While this is happening it appears to be checking my CD and DVD drives. Any advice would be appreciated. ~Kelt~