Jump to content
Sign in to follow this  
red930

(AM2) LanParty NF590 SLI-M2R/G / OCZ OCZ2P100001GEEK (1GB x 2) 4-5-4-1

Recommended Posts

DFI LP UT NF590 SLI-M2R/G Socket AM2 NVIDIA nForce 590 SLI MCP ATX AMD Motherboard BIOS 8/29

 

AMD Athlon64 X2 Windsor 4600 (2400Mhz / 512KB L2 per core)

 

OCZ OCZ2P10001GEEK (1GB x 2) 4-4-4-12 Dual Channel

 

MSI X850 PCI-E 16x 128MB, ATI Catalyst 6.9, 400/350

 

[email protected] 80GB SATA 3.0Gbps Drives RAID-0

 

NEC 3550A CD/DVD RX

 

OCZ GameXStream 600W Power Supply

 

 

*

*

 

==========

 

 

[b]Genie BIOS Settings:[/b]

[color=red]

CPU Clock Multiplier ............  -  X 12

CPU/C51 HTT Frequency............  -  Auto

CPU/C51 HTT Multiplier...........  -  Auto



C51/MCP55 HTT Frequency..........  -  Auto

C51/MCP55 HTT Multiplier.........  -  Auto

PCI-E Slot4 Clock................  -  100Mhz

PCI-E Slot1 Clock................  -  100Mhz



CPU VID Control..................  -  Auto

CPI VID Special Add..............  -  Auto

C51 NB Core Voltage..............  -  1.20v

MCP55 SB Core Voltage............  -  1.50v

MCP55 SB Standby Voltage.........  -  1.5v

CPU/C51 HT Drive Strength........  -  Low, Low

CPU/C51 HT Voltage...............  -  1.30v

C51/MCP55 HT Voltage.............  -  1.30v

DRAM Voltage Control.............  -  2.00v

[/color]



[b]DRAM Configuration Settings:[/b]

[color=red]

Memclock Tri-Stating.............  -  Disabled

Memory Hole Remapping............  -  Enabled

Auto Optimize Bottom IO..........  -  Enabled



DRAM Drive Strength..............  -  Level 15

RAM Drive Weak/Normal Mode.......  -  Auto

CLK Enable Drive Strength........  -  Auto

Chip Select Drive Strength.......  -  Auto

MEM Address Drive Strength.......  -  Auto

MEM Clock Drive Strength.........  -  Auto

Memory Data Drive Strength.......  -  Auto

Data Strobe Drive Strength.......  -  Auto

CS/ODT Pin Fine Delay............  -  Enable



SLI-Ready Memory.................  -  Disable

Timing Mode......................  -  Manual

Memory Clock Value/Limit.........  -  400Mhz

Command Per Clock (1/2T).........  -  2T 

CAS Latency Control (Tcl)........  -  004 CLK

Min RAS Active Time (Tras).......  -  012 CLK

RAS to CAS Delay.................  -  005 CLK

Row Precharge Time (Trp).........  -  004 CLK

RAS to RAS Delay (Trrd)..........  -  003 CLK

Row Cycle Time (Trc).............  -  023 CLK

DIMM 1 Row Refresh (Trfc0).......  -  075 ns

DIMM 2 Row Refresh (Trfc1).......  -  105 ns

DIMM 3 Row Refresh (Trfc2).......  -  075 ns

DIMM 4 Row Refresh (Trfc3).......  -  075 ns

Read Precharge Time (Trtp).......  -  002 CLK

Write Recovery Time (Twr)........  -  006 CLK

Read to Write Delay (Trwt).......  -  004 CLK

Write to Read Delay (Twtr) ......  -  003 CLK

Refresh Period (Tref)............  -  03.9 us

Max Asynch Latency...............  -  006 ns

Bank Interleave..................  -  Auto

DRAM On-Die Termination..........  -  075 ohm

Read Delay From Rx FIFO..........  -  2.5 CLK

Read/Write Queue bypass..........  -  08 time

Bypass Maximum...................  -  04 time

32 Byte Granularity..............  -  64-Byte

Idle Cycle Limit.................  -  16

Dynamic Counter..................  -  Enable

Read DQS Skew....................  -  Auto

[/color]

 

 

==========

 

 

Orthos (SP2004) + 3dMark2001SE + 2x CPU-Z + Everest Ultimate 3.5:

 

http://myweb.cableone.net/mondo/screen1oczstock.JPG

 

 

3dMark2003:

 

3dmark03oczstock.JPG

 

 

3dMark2005:

 

3dmark05oczstock.JPG

 

 

3dMark2006:

3dmark06oczstock.JPG

 

 

 

==========

 

 

short description:

200x12 @ 2400mhz 1.375vcore / 2.00vdimm

4-5-4-12

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

×
×
  • Create New...