pgaur82 Posted June 30, 2006 Posted June 30, 2006 What voltages are you trying to run? Share this post Link to post Share on other sites More sharing options...
red930 Posted July 1, 2006 Posted July 1, 2006 Well, every rig is different. At the very least, you can take the timings given as an example and relax them a bit as a starting point. It takes time and effort to get a rig setup. You'll need to invest your energy in getting things right. Hello, i tried just like you told me to do, but the windows still doesn t work if I put the ram more than 166. As obs, the cpuz doesn t show the rams frequency or FSB just the timings. Do I have bad rams? What should I do? Thanks Share this post Link to post Share on other sites More sharing options...
Reisender Posted July 7, 2006 Posted July 7, 2006 the rams fails with the memtest86, do I have bad rams? should I try more voltages than 2.66? Thanks Ps I tried this one, but still can t get windows to work with more then 140 FSB Bus Frequency............................. 200 MHz LDT/FSB Frequency Ratio....................... 4 CPU/FSB Frequency Ratio....................... 8 PCI eXpress Frequency......................... 100 CPU Voltage .................................. 1.300V Above CPU VID................................. 109.6% LDT Voltage .................................. 1.20v ChipSet (NF4) Voltage ........................ 1.52V DRAM Voltage ................................. 2.66V +0.03 if not 3.2V ............................ N/A Memclock (DRAM Frequency) .................... 200 1T/2T Timing (Command Per Clock).............. 1T (CPC enabled) CAS Latency (Tcl)............................. 3T RAS# to CAS# delay (Trcd)..................... 3T Min RAS# active time (Tras)................... 8T Row precharge time (Trp)...................... 2T Row Cycle time (Trc).......................... 10T Row refresh cyc time (Trfc)................... 16T Row to Row delay (Trrd)....................... 3T Write recovery time (Twr)..................... 3T Write to Read delay (Twtr).................... 2T Read to Write delay (Trwt).................... 3T Refresh Period (Tref)......................... 3120 DRAM Bank Interleave.......................... Enabled DQS Skew Control.............................. Auto DQS Skew Value................................ 0 DRAM Drive Strength........................... Level 08 DRAM Data Drive Strength...................... Level 2 (Reduce 30%) Max Async Latency............................. 8ns DRAM Response Time............................ Normal Read Preamble Time............................ 6ns IdleCycle Limit............................... 64 Dynamic Counter............................... Disable R/W Queue Bypass.............................. 16x Bypass Max.................................... 4x 32 Byte Granularity........................... Disable (4 Bursts Share this post Link to post Share on other sites More sharing options...
tasr Posted July 7, 2006 Posted July 7, 2006 For stock settings try the following then run memtest #5 and #8 for 10 passes. Genie BIOS Settings: FSB Bus Frequency............................. - 200 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - Auto PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - Auto CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.7v then 2.8v DRAM Configuration Settings: DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable or 1T CAS Latency Control (Tcl)..................... - Auto RAS# to CAS# delay (Trcd)..................... - Auto Min RAS# active time (Tras)................... - Auto Row precharge time (Trp)...................... - Auto Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) Share this post Link to post Share on other sites More sharing options...
Reisender Posted July 9, 2006 Posted July 9, 2006 hello, I tried the modules in the orange slots, now the rams works with the first configuration at 260, cpu fsb 260, can t get more with this opteron, 270 is overkill, it s a CCBWE, I want to put a WC to rise the voltage, but I don t think I ll get better than that. Thanks for all the people that helped Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now