s.win Posted February 24, 2006 Posted February 24, 2006 hi u flashed my nf4 ultra-d with tonys 704-2bta now i cant boot any more.... so what can i do now??? is the bios only for ultra? thought also for my mobo .... damn edit: i got 2 leds lightened up Share this post Link to post Share on other sites More sharing options...
blick Posted February 24, 2006 Posted February 24, 2006 Calm down and Clear CMOS then load defaults and only then put your usual settings. Your PSU isn't adequate. Share this post Link to post Share on other sites More sharing options...
s.win Posted February 24, 2006 Posted February 24, 2006 thanks for your answer i still hangs and i get one led now.... edit: ok it works.... i put off one piece of ram sorry for my bad english Share this post Link to post Share on other sites More sharing options...
HITandRUN Posted February 24, 2006 Posted February 24, 2006 You need a new PSU! The 370 is not enough for your system! :shake: Share this post Link to post Share on other sites More sharing options...
s.win Posted February 24, 2006 Posted February 24, 2006 yes it is enough! why isnt it? in the manual you can read it is... Share this post Link to post Share on other sites More sharing options...
HITandRUN Posted February 24, 2006 Posted February 24, 2006 Well check this out! These are the guide lines for any of the NF4 boards! (Written in red) http://www.dfi-street.com/forum/showthread.php?t=10854 :nod: Make a DFI recommended CMOS clear (look in my sig. there is a link on how to do it) and that only put in one stick of ram in the top orange ram slot. Boot up, save optimized defaults (adjust the ram voltage to 2.8) and shut down again. Install the second ram stick and there you go! It should be working! :nod: Share this post Link to post Share on other sites More sharing options...
s.win Posted February 24, 2006 Posted February 24, 2006 i did it like this way: flashed the bios and did afterwards a cmos clear... now it works... is this ok? @hitandrun: just red the proper clear CMOS recovery!!! .......so whats the difference between a "normal" clear cmos and this one above? so what would you recommend to me to flash my bios correctly to tonys version? Share this post Link to post Share on other sites More sharing options...
gokee2 Posted February 24, 2006 Posted February 24, 2006 wells, if it works and its fine by you then i guess its fine. like everyone else has said, your PSU is too weak. Sorry, i did not intend any disrespect. Just a DFI dude looking our for another DFI dude Share this post Link to post Share on other sites More sharing options...
s.win Posted February 24, 2006 Posted February 24, 2006 why do you guys think my psu is not enough? well if it WAS no enough how would i recognize it? cos my computer has been working correctly for a year now... (now i doesnt cos memtest shows errors. it seems one memory module is broken ;-( ) thanks for ya help Share this post Link to post Share on other sites More sharing options...
HITandRUN Posted February 24, 2006 Posted February 24, 2006 @ s.win! You didn't read the link I gave you about the recommended PSU’s! Did you? If you would have read the link you would know what AngryGames was talking about! Ich versuche dir zu helfen und du machst hier die ignoranten tour! :shake: Share this post Link to post Share on other sites More sharing options...
s.win Posted February 24, 2006 Posted February 24, 2006 bin nicht ignorant! viell. dickkopf Share this post Link to post Share on other sites More sharing options...
blick Posted February 24, 2006 Posted February 24, 2006 It's working now? And please post in english. Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now