potseeker

The chiller is a stand alone unit with it own pump and coolant loop..the heat will be transfered using tubular heat exchanger.

My silverstone st85f modular has two 35amp +12v rails...my chiller uses eight low wattage tec's that will require about 45 amps...what want to do is split the load between the two 12v rails...my problem is the pcie load is split between the two rails...the two cables are the same and the location of the 12v1-12v2 outlets are not marked on the unit or in the guide..now the question how do I use my multimeter to match these outlets with the other 12v1-12v2 wires...Thanks

Thanks all, I was going to give these settings a try and run memtest tonight... what would you change to loosen the timings... Memclock (DRAM Frequency) .................... 200 1T/2T Timing (Command Per Clock).............. 1T (CPC Enabled) CAS Latency (Tcl)............................. 3T RAS# to CAS# delay (Trcd)..................... 4T Min RAS# active time (Tras)................... 8T Row precharge time (Trp)...................... 3T Row Cycle time (Trc).......................... 11T Row refresh cyc time (Trfc)................... 16T Row to Row delay (Trrd)....................... 3T Write recovery time (Twr)..................... 3T Write to Read delay (Twtr).................... 2T Read to Write delay (Trwt).................... 3T Refresh Period (Tref)......................... 3120 DRAM Bank Interleave.......................... Enabled DQS Skew Control.............................. Auto DQS Skew Value................................ 0 DRAM Drive Strength........................... Level 07 DRAM Data Drive Strength...................... Level 2 (Reduce 30%) Max Async Latency............................. 8ns DRAM Response Time............................ Normal Read Preamble Time............................ 6ns IdleCycle Limit............................... 128 Dynamic Counter............................... Disable R/W Queue Bypass.............................. 16x Bypass Max.................................... 4x 32 Byte Granularity........................... Disable (4 Bursts)

Just what I want to avoid killing it with to high of voltage thats why I decided to post this first... I thought I had read in other threads that working the memory controller to hard could limit a overclock...

I've not tried Orthos but I know just 1 MHz increase FSB and Prime will fail after 3-4 hours..my last increase in volts from 1.65 to 1.67 allowed 2MHz more FSB and know change in temps... so increases in voltage so far have allowed small gains...

If I understand correctly with FSB set at 246 and LDT set at 4 keeps my HTT under 2000...the ram will run 264 MHz but I will have to raise or lower my clock to utilize that speeds...correct??.. new at this overclocking fun.

I'm getting the itch to push my overclock higher but I don't want to just throw more volts at the cpu (1.67v@2952MHz) it seem to me thats already high for the overclock but temps are all good and system is stable cpu can reach 47c during prime a few less when gaming and idle temps less than 30c. Memtest 8hr no errors but I believe some tweaking of secondary settings might yield a higher clock I'm posting my bios settings any help greatly appreciated. FSB Bus Frequency............................. - 246 LDT/FSB Frequency Ratio....................... - 4.0 CPU/FSB Frequency Ratio....................... - 12 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.525v CPU VID Special Control....................... - 109.6 LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.80v[/color] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Auto CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 04 Min RAS# active time (Tras)................... - 08 Row precharge time (Trp)...................... - 03 Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 08.0 DRAM Response Time............................ - fast Read Preamble Time............................ - 06.0 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 06 x 32 Byte Granularity........................... - Disable(Bursts)

Well I could not complete the bios flash because of a missing source file not sure if the missing file was part of awdflash or the new bios or the old bios...but no harm was done...I've got to find that Sticky on bios flashing anyone know where to find it...

Ok but what is the a prompt all about do have to type adwflash.exe again and start over or after inserting a new floppy will it continue to copy the old bios...is there any way to just back out of this or just shut down..Thanks

Ok Im trying to cure my SLI troubles by flashing the bios from 2005/12/07 to 2006/04/06 but now Im in trouble when I tried to save the old bios I got a Warning disk is full or file error now it sits there in the AWDFLASH utility with a flashing A prompt just below....should I have inserted a new disk to save old bios to...I dont know what to do next this cant be good..Help!!

thanks where can I find that I could not find anything doing a search for bios flash

Ok Im trying to cure my SLI troubles by flashing the bios from 2005/12/07 to 2006/04/06 but now Im in trouble when I tried to save the old bios I got a Warning disk is full or file error now it sits there in the AWDFLASH utility with a A prompt flashing just below....should I have inserted a new disk to save old bios to...I dont know what to do this cant be good..Help!!

I have considered flashing but I have not had any problems with my corsair memory hate to open another canoworms before resolving this problem...the card was to be three weeks old from zipzoom and had not yet been registered... I might be able to RMA it..

Ok tried removing the power connectors from both cards booted into windows...low power caused the gpu to slow down to a snails pace...loaded drivers and applied the sli with the same results...disabled the bios settings and rebooted to windows where it told me sli had been disabled and the system had recoverd from a serious error...

The cards had different coolers when I got them (ebay should know better)) but are both evga and have the same bios..