lunari

Okay, I'll give that a try after I get off of work tonight. Thanks!

Not cool with it at all, just want to get my system going once again. It may be showing it's age a slight bit, but it's still a beast

Hello, this is in regard to the main system listed in my sig. I recently moved and left my computer for storage with a friend. When I returned to pick it up they had removed my HDD and my video card (which they had wraped up in a dish rag)... Anyways, I drive the nearly ~400 miles to the new house. I put the video card in, borrow a HDD from a friend and... Nothing... It powers on, but there is no output from the video card. What leads me to believe it's a motherboard issue is that it doesn't work with any card I have access to (7900GTO, 7600GT, X300). The weird thing is, after not displaying anything, it displayed video for about 10 seconds, and since then it won't display anything. I believe these boards have a one year warranty (which it's still under), I'm not quite sure where to start.. making sure it's the board etc.. and if so how to go about fixing the problem, whether by RMA (if it's possible) or what. Thanks, Lunari Edit: There are no post beeps either for some reason..

Mx518

Connect that floppy power connector then, it's there for a reason :nod:

The CPU-Z validator link I have posted doesn't show my memory timings. I haven't posted any Everest benches yet. Edit: maybe he was referring to xtw1ster I see he has HZ sticks also and lists them at 2t in his sig.

Way back when, in my s754 board with my Newcastle 3000+ I had my G.Skill HZ running at ~275

At boot it says 1T, also 1T in CPU-Z, where are you seeing 2T? Oh, and the RAM settings I am using I found in a review of the sticks, if you have a link to better (faster) ones, please share.

CoreTemp readings: Core 0 Idle: 26c Core 1 Idle: 33c Core 0 Load: 40c Core 1 Load: 47c Kind of wierd how Core 0 is so much cooler than Core 1 :confused:

Ah, they were from SmartGuardian, let me go get CoreTemp and check it out. Added my 3dMark01 results also.

Here are the OCDB style results I said I would post. I will update it as I download/install the programs. DFI LANPARTY UT nF4 SLI-DR (BIOS that was shipped on it.) AMD Opteron 165 dual core 2x1024MB G.Skill HZ Extreme PC-4000 eVGA 7900GTO, 685/1440: 93.71 Drivers 80GB WD 8MB Cache, SATA hdd Nu Technologies DVD+RW OCZ GameXstream 600w * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 312 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.375v CPU VID Control............................... - 1.375v CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 133=RAM/FSB:2/03 Command Per Clock (CPC)....................... - Auto CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 07 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 14 Bus Clocks Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: Coming Soon, 3dMark01, CPU-Z, Coming Soon 3dMark2003: 3dMark03 3dMark2005: 3dMark05 3dMark 2006: 3dMark06 ========== short description: 212x9 @ 2808Mhz, 1.375v BIOS/1.34v Actual, 3-3-3-7 @ 2.70v vdimm

Sitting rock solid stable at 2.8Ghz currently, still at 1.34v. Running a tuniq tower, 29c idle, 38c under dual prime load. Room temp is generally around 65-70f. I got it to boot into windows at 3.0Ghz at 1.4v or so, was stable enough for use, but would fail dual prime instantly. Edit: Can't do any SuperPI testing, because for some reason even at stock speeds it would BSOD on me. Edit #2: My CPU-Z validation at my stable 2.8Ghz/1.34v http://valid.x86-secret.com/show_oc.php?id=148421

The chip I ordered last week (Opty 165) was a CCBBE 0615, sitting rock solid stable 2.8Ghz at 1.34v.

Decided not to really push it just yet, sitting dual prime stable at 2.7Ghz, 1.34v.

Oops, I meant 1.45v, damn typos