Ytterbium

Mine just won't go higher, well maybe 50Mhz but who cares

Mine does 270, not much more tho

I wasn't as I was running 32bit windows

I have PP&C, I don't think there's much diffrence TBH

Mines hit the wall @ 2.7 ish, if I do 2.8 dual prime fails after less than an hour always on core #1 even with 2.7V I can load windows @ 300x9, but I had to back off the ram settings and prime wasn't stable, the Balistix don't seem very happy @ 300Mhz. Here's my setting's http://www.dfi-street.com/forum/showpost.p...73&postcount=80

What about a 6800GS, there £160 in the UK. This ram should be pritty good? http://www.ocztechnology.com/products/memo...ual_channel_kit

DFI LanParty NF4 UT SLI-DR, BIOS 6/23/2005-3 AMD AthlonX2 3800+ Manchester, (E4) 2x1024MB Crucial Balistix (Z503) Leadtek 6600GT 128MB, 500/1000 81.85 drivers Western Digital Raptor 74GB SATA hdd (8MB cache) Lite-On 1653S CD-ROM Drive PC Power and Cooling Turbo Cool 510 SLI ATX 510W Power Supply Prometia Mach I Phase Change ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - X 10.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.500v CPU VID Special Control - Above VID * 110% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:1/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 10 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - 01 Bus Clock DRAM Bank Interleave - Enabled DQS Skew Control - Increase Skew DQS Skew Value - 255 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 3 Max Async Latency - 7.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 4.0 Nano Seconds IdleCycle Limit - 016 Cycles Dynamic Counter - Enable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.31: http://homepage.ntlworld.com/tbroom/T1.JPG 3dMark2003 + Everest 2.20 + Super PI 1.4: http://homepage.ntlworld.com/tbroom/T2.JPG 3dMark2005: Aquamark 3d: ========== short description: 270x10 @ 2700Mhz, 1.500v + 110% 3-3-8-3 @ 2.7v vdimm

OK, I asked because of the divider thread, if your shooting for max cpu what's the point of running the ram faster (other than cudos).

What the point of having 300x9 vs 270x10?

Don't feel bad my chip is only doing 2.7Ghz, with phase change

I took the fan of the cpu cooler that came with my FX-53, now @ 40-41,

Mines running at 60-61dC, I think I'm in need of cooling

It depends on your gfx card? with my 660GT the card is over the cooler now, I can't see how this is smaller than std one.