AnjinSan1966

See my sign

HOMM II & III :nod: , DoW, WC3.

Its a better idea to get a D-Link,Linksys or such if u want a hardware firewall that works.Not many are happy with the the nV Firewall.

My score7499p

I must say i love this DFI-board that i have now.Before this i had a MSI NF3 754 board and before that a ABIT NF7 Socket A.They have all been fine but the DFI is flying fast and flawless

Those mem´s ar sweet :shake: . I am very pleased with mine so far stable up to 300

Hehe :nod: score soundX98.Now i have to tweak even more dam u :shake:

Tightened the timings some and manged this:

Try to raise the Volt to 2.9.It made me able to run at 1t at 300FSB.

Been doin some new benchmarks with settings in sig. 3DMark05 7411p 3DMark03 15386p 3DMark01 32052p Aquamark3 91601p Everest Mem Read Everest Mem Write Everest Mem Latency

Yea im pretty happy with this build so far.Been experementing with dividers and such.Cpu can do 315FSB but mem wont go over 305.I tested with 183mhz on mem and 200 on Cpu and got somewhat better scores.Dont know whts best as both settings seems stable so far.Well back to the tests.L8rs all

I had the same problems with not getting 1t working so i raised the Vcore to 3.0V from 2.9V and now its stable in all benchmarks etc.But thers not much diffrence in the tests so far.I dont think its worth it.

Benchmark results posted here http://www.dfi-street.com/forum/showpost.p...33&postcount=24

DFI LANPARTY nF4 SLI-DR - 6/23-2 BIOS AMD Athlon 64 3000+ Venice Socket 939 Processor Model ADA3000BPBOX - LBBLE 0517 EPAW stepping 2x512MB OCZ EL Platinum revision 2 V1.1 TCC5 memory Sapphire Radeon X850XT 256MB GDDR3 PCI-Express,ViVO,Dual DVI-ICATALYST 5.7 - 618/615 2x Samsung SpinPoint P80SD 80GB SATA2 8MB 7200RPM NCQ (RAID-0) Plextor PX-716A - DVD±RW Silverstone ST65ZF 650W PSU SLI-Certified, Dual PCI-E, 20/24pin Thermalright XP-120 aluminum heatpipe heatsink + Papst 4412FGML 120x120x25mm ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ration - x3 CPU/FSB Frequency Ratio - x9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.5000v CPU VID Control - 1.300v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 12 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 09.0 Nano Seconds Read Preamble Time - 05.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + Everest 1.51: http://img297.imageshack.us/my.php?image=pic14jb.jpg 3dMark2003: http://img297.imageshack.us/my.php?image=pic26kv.jpg 3dMark2005: http://img297.imageshack.us/my.php?image=pic36bc.jpg Aquamark 3d: http://img345.imageshack.us/my.php?image=pic45mx.jpg ========== short description: 300x9 @ 2700Mhz, 1.300v + 123% 2.5-4-8-4 @ 2.93v vdimm

Have completed all of the 3Dmark´s,Aquamark,Everest and SuperPi 1M -> 32M. Running Prime95 now. So far it has been flawless.