psychomage343 Posted August 4, 2005 Posted August 4, 2005 i've got a lanparty nf4-d, i cna't post after 236 fsb unless my ram is at a 1/2 ratio. I've got kingston hyperx spd settings are 2.5,3,3,8. What am i doing wrong. i can boot at 290x10 with a 3500 venice on cool water. i can boot 2.6 at 236x10 with the ram at a 166 divider. Maybe my timings are off, can someone help please. I was told angry was an expert on this board. maybe he can help me get the settings i need. I also had this ram at 270x10 at 2.7 on an asus board, but i didn't have to tune timings at all to get it. please help me. Quote Share this post Link to post Share on other sites More sharing options...
Sharp Posted August 4, 2005 Posted August 4, 2005 Hello, What power supply What gfx card What memory, Model number/chips on it. Did you plug all 4 power connectors into the DFI board? And the ASUS boardm was it an intel board? Quote Share this post Link to post Share on other sites More sharing options...
Frallan Posted August 4, 2005 Posted August 4, 2005 That ^^ and also a sig please with all your HW in it :dog: Quote Share this post Link to post Share on other sites More sharing options...
psychomage343 Posted August 4, 2005 Posted August 4, 2005 i got an ocz powerstream 520, and yes everything is plugged in, and i upgraded my sig, plus it's a radeon x850 xt pe Quote Share this post Link to post Share on other sites More sharing options...
psychomage343 Posted August 4, 2005 Posted August 4, 2005 oh yes, and the asus board was not an intel it had the same everything that is in this computer, all i did was switch boards Quote Share this post Link to post Share on other sites More sharing options...
psychomage343 Posted August 5, 2005 Posted August 5, 2005 is there nobody that can help me Quote Share this post Link to post Share on other sites More sharing options...
RGone Posted August 5, 2005 Posted August 5, 2005 I did not see this thread you had started already so put the stuff I mentioned in the PM in a post after this and will try to be back later to look and see how it is all setup. Don't forget to list all and the bios as well. RGone... Quote Share this post Link to post Share on other sites More sharing options...
Joop Posted August 5, 2005 Posted August 5, 2005 is there nobody that can help me This is my HyperX PC3200 memory setting @ 262.0 MHz, see my sig! for more details, maybe this help you a little. Genie BIOS setting DRAM Configuration DRAM Frequency set 200 MHz (DRAM/FSB: 1 / 01 ) Command Per Clock ( CPC ) 1T/2T Enabled 1T CAS Latency Control ( Tcl ) 3.0 RAS# to CAS# active time ( Trcd ) 04 Min RAS# active time ( Tras ) 10 Row precharge time ( Trp ) 04 Row cycle time ( Trc ) 12 Row refresh cycle time ( Trfc ) 14 Row to Row delay ( Trrd ) 02 Write recovery time ( Twr ) 03 Write to Read delay ( Twtr ) 02 Read to Write delay ( Trwt ) 04 Refresh period ( Tref ) 200(3.9 us) 3072 Write CAS latency ( Twcl ) 1 DRAM Bank Interleave Enabled DQS Skew Control Increase Skew DQS Skew Value 32 DRAM Drive Strength Level 2 Max Async Latency 07.0 Nano Seconds Read Preamble Time 05.0 Nano Seconds Idle Cycle Limit 016 Cycles Dynamic Counter Enabled R/W Queue Bypass 08 X Bypass Max 04 X 32 Byte Granularity Disabled (8 Bursts) Thermal Throttling Disabled ====================================================== My HyperX PC3200 memory setting @ 250.0 MHz, see also my sig! by 'Relaxed' for details. DRAM Frequency set (MHz) 200 MHz (DRAM/FSB: 1 / 01 ) Command Per Clock ( CPC ) 1T/2T Enabled 1T CAS Latency Control ( Tcl ) 2.5 RAS# to CAS# active time ( Trcd ) 03 Min RAS# active time ( Tras ) 05 Row precharge time ( Trp ) 03 Row cycle time ( Trc ) 09 Row refresh cycle time ( Trfc ) 14 Row to Row delay ( Trrd ) 02 Write recovery time ( Twr ) 02 Write to Read delay ( Twtr ) 02 Read to Write delay ( Trwt ) 02 Refresh period ( Tref ) 200(3.9 us) 3072 Write CAS latency ( Twcl ) 1 DRAM Bank Interleave Enabled DQS Skew Control Increase Skew DQS Skew Value 96 DRAM Drive Strength Level 2 Max Async Latency 07.0 Nano Seconds Read Preamble Time 05.0 Nano Seconds Idle Cycle Limit 016 Cycles Dynamic Counter Enabled R/W Queue Bypass 08 X Bypass Max 04 X 32 Byte Granularity Disabled (8 Bursts) Thermal Throttling Disabled EDIT: btw my HyperX PC3200 SPD 2.5,3,3,8 is the same Quote Share this post Link to post Share on other sites More sharing options...
RGone Posted August 5, 2005 Posted August 5, 2005 Thanks 'joop' man. RGone... Quote Share this post Link to post Share on other sites More sharing options...
psychomage343 Posted August 5, 2005 Posted August 5, 2005 well guys, no luck i tried both configs and still only get to the verifying dmi pool data or whatever. After that instant reboot, or just hangs, any other ideas, i'm pretty sure my bios settings besides that are correct, i'm just stumped Quote Share this post Link to post Share on other sites More sharing options...
psychomage343 Posted August 5, 2005 Posted August 5, 2005 well here is the sad truth, i've got some no name ram no ramsinks, or heatspreader, and it runs 250 1-1, lol, i got it stable here at 2.70ghz 1.66vcore, 2.9vdimm, 1.5 chipset, and stable, 10hrs prime so far, passed memtest #5 a bunch of times, and i don't even know the name of the ram, can't even read the serial number. i think it's ld, but who knows Quote Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.