Jump to content
Sign in to follow this  
tomtsops

3700+ San Diego Bios Version Please Post

Recommended Posts

IIRC- CPU VID Startup is the voltage the CPU gets during POST/In BIOS

 

Then once Windows boots, it adjust to the CPU VID Control + CPU Vid Special Control

Share this post


Link to post
Share on other sites
I thought the 704-2 bios caused the CPU to overvolt?

 

OczTony modded the 704-2 and is now the 704-2BT and it works very well. Of course it is beta for sure

 

Its a modded version that has the bad vid specials taken out.. But its not available to DL.. Its just being tested I believe..

 

hey thunda,

 

Can you explain this:

 

CPU VID StartUp Value - 1.55v

CPU VID Control - 1.325v

CPU VID Special Control - Avove VID * 126%

 

Does this mean you start up at 1.55V on your cpu and eventually go to 1.6695V ?

 

 

IIRC- CPU VID Startup is the voltage the CPU gets during POST/In BIOS

 

Then once Windows boots, it adjust to the CPU VID Control + CPU Vid Special Control

 

What mack73 said.. :)

Share this post


Link to post
Share on other sites

Currently I'm running at 2.75ghz on the 3/10 bios with my PC4000VX ram, though I'de liek to go higher. I can bench everything, as many times as I would like, but prime errors out within the forst 10 minutes. I can leave OCCT on forever and its fine. Anyways, these are the settings I'm running right now. If anyhone has ideas on how to get more out of this, any help would be valued. As with a bios, there is no best. All you can really do is try them all and see which one gives you the most for your rig.

 

Genie BIOS Settings:

FSB Bus Frequency - 250

LDT/FSB Frequency Ration - x3.0

CPU/FSB Frequency Ratio - x11.0

PCI eXpress Frequency - 100Mhz

 

CPU VID StartUp Value - 1.5v

 

CPU VID Control - 1.300v

CPU VID Special Control - Avove VID * 123%

LDT Voltage Control - 1.20v

Chip Set Voltage Control - 1.50v

DRAM Voltage Control - 3.30v

 

 

DRAM Configuration Settings:

DRAM Frequency Set - 200 (DRAM/FSB:1/01)

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 1.5

RAS# to CAS# delay (Trcd) - 02 Bus Clocks

Min RAS# active time (Tras) - 05 Bus Clocks

Row precharge time (Trp) - 02 Bus Clocks

Row Cycle time (Trc) - 07 Bus Clocks

Row refresh cyc time (Trfc) - 16 Bus Clocks

Row to Row delay (Trrd) - 02 Bus Clocks

Write recovery time (Twr) - 02 Bus Clocks

Write to Read delay (Twtr) - 01 Bus Clocks

Read to Write delay (Trwt) - 02 Bus Clocks

Refresh Period (Tref) - 2560 Cycles

Write CAS Latency (Twcl) - 01 Bus Clocks

DRAM Bank Interleave - Enabled

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Level 8

DRAM Data Drive Strength - Level 4

Max Async Latency - 6.0 nanoseconds

Read Preamble Time - 5.5 nanoseconds

IdleCycle Limit - 16 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(8 Bursts)

Share this post


Link to post
Share on other sites

All you using 310 bios with a Sandy..Venice or x2 should update your bios to 623 which is on DFI's site.. 510 bios and newer supports revE cpu's..

Share this post


Link to post
Share on other sites

XP-90 and special 3 blade fan.

 

RGone...

 

Hey RGone what cooling were you using there??

Share this post


Link to post
Share on other sites
3.16 bios, I cant get it prime 95 stable over 2.7 gigs

 

i upped my chipset voltage to 1.6 and i can now boot into windows with it @ 2.81Ghz from a previous best of 2,7Ghz with chipset @ 1.5V.

 

I am currently priming @ 2.7ghz with 1.55Vcore been going a few hours now

 

i did have it @ 2.75 w/ 1.58V for 2 hours with no error but backed off coz temp reached 50*c

 

it's now @ 47* priming and folding @ the same time

Share this post


Link to post
Share on other sites
i upped my chipset voltage to 1.6 and i can now boot into windows with it @ 2.81Ghz from a previous best of 2,7Ghz with chipset @ 1.5V.

 

I am currently priming @ 2.7ghz with 1.55Vcore been going a few hours now

 

i did have it @ 2.75 w/ 1.58V for 2 hours with no error but backed off coz temp reached 50*c

 

it's now @ 47* priming and folding @ the same time

 

I'll have to try 1.6v on the chipset. I've changed case cooling since my last oc attempts.

Share this post


Link to post
Share on other sites

623-3

 

havnt primed or anything but Ive been running for 4+ weeks gaming,browsin etc. about 6-8 hrs per day

 

no BSOD/lockups etc.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...