Jump to content

OCZ Golds wont boot over 3.2v


Oclock

Recommended Posts

So ive been burning these in according to this forum http://www.bleedinedge.com/forum/showthread.php?t=11442 But the problem is i cant boot with the 3.3v on step 9. Everything up until then has run smoothly. I raised my psu to 3.45, using a DMM,as advised but it just leads to a "detecting array" i tried lowering the fsb and 3.3 but still a no go. So last night i just looped all tests at 3.2v 220 with about 19000 errors, eww. im really confused on what i should do next.

 

And as of right now i can run 225 stable with 3.1v 2-2-2-5.

Share this post


Link to post
Share on other sites

Sometimes the 3.3v rail needs to be higher then just .15v of the vdimm.. I would raise it to 3.5v and see if that makes a difference..

 

Also make sure you unplug your psu and clear the cmos with the battery out for 10mins.

Share this post


Link to post
Share on other sites

From top to bottom in BIOS

 

DRAM

200

enable

2

2

5

2

7

17

2

2

2

2

3120 Cycles

Auto

 

Auto

0

Auto

Auto

256 Cycles

Disable

16x

7x

Disable

 

Genie

 

220

66

Disabled

Auto

Auto

3x

10x

Disable

 

Auto

Auto

1.6v

1.7v

3.3v

 

This is the next step i cant get to work

Share this post


Link to post
Share on other sites

try this:

 

cl1.5:

A-A-1.5-2-2-2-9-12-2-2-1-2-3120-A-E-A-0-3-1-6/7/8-F(ast)/N-5/5.5/6/6.5-16/128-D-16-7-D

 

cl2:

A-A-2-2-6-2-10-12-2-2-2-3-3120-A-E-A-0-3-1-6/7/8-F(ast)/N-5/5.5/6/6.5-16/128-D-16-7-D

 

LDT: 3x>248, 4x<248

PCI-E Payload: 128 if using Manual LDT, 4096 if using Auto LDT

vCHIP, vLDT: keep at stock and only raise if u need to

 

good luck.

Share this post


Link to post
Share on other sites

well i got it to work right now with this

cl1.5:

A-A-1.5-2-2-2-9-12-2-2-1-2-3120-A-E-A-0-3-1-6/7/8-F(ast)/N-5/5.5/6/6.5-16/128-D-16-7-D

but i dont understand whats in bold... so i set it o auto-7. And i dont even have an option that says PCI-e payload, let alone a pci-e board. I dont quite understand that whole deal yet. But i did set it manualy at 4x and 128.

Share this post


Link to post
Share on other sites

nvm i take that back, i walk away for a few minutes and i get a gazillion errors. so i tried the other timing and same thing. this is at 220 fsb and 3.3v. note i only got errors in test 5. I also noticed there are some extra things you have listed that are not in my bios, am i using the wrong one? its the 10/15 jsj w/ 4v dimm.

 

*update* Ok idk what the hell i just did but i got it to work at 3.3v 220 fsb. I used the settings Andy had suggested and so far it seems to be working(knock on wood). il update my next progress later but i am still wondering whether or not i have chosen the right bios cuz this one doesnt have bank interleave on it.

Current settings

200-e-2-2-6-2-7-14-2-3-2-2-*0648*main difference-a-a-0-level2-7-a-256-d-16-07-d

Share this post


Link to post
Share on other sites

nvm i take that back, i walk away for a few minutes and i get a gazillion errors. so i tried the other timing and same thing. this is at 220 fsb and 3.3v. note i only got errors in test 5. I also noticed there are some extra things you have listed that are not in my bios, am i using the wrong one? its the 10/15 jsj w/ 4v dimm.

 

*update* Ok idk what the hell i just did but i got it to work at 3.3v 220 fsb. I used the settings Andy had suggested and so far it seems to be working(knock on wood). il update my next progress later but i am still wondering whether or not i have chosen the right bios cuz this one doesnt have bank interleave on it.

Current settings

200-e-2-2-6-2-7-14-2-3-2-2-*0648*main difference-a-a-0-level2-7-a-256-d-16-07-d

 

ahh your on nf3. you should have most of the settings. some things wont apply though. my mistake, i thought you were on nf4.

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...