Jump to content
Sign in to follow this  
Sgarv

Are there any memory timings posted for OCZ 2gig?

Recommended Posts

Ive been looking for bios memory timings for my specific memory over several forums (including OCZs) and thought i would try this one for answers first. One of the problems ive been seeing is memtest errors on test 6. The memory is new. I just tried switching the sticks from slot 2 and 4 to 1 and 3 looking for error elimination.

Memory in question: OCZ platinum 1024 x 2 , model no. OCZ4002048ELDCPE-K

thx

 

NF4 Ultra-D BIOS 3 / 10

A-64 3200Win

ATI X800XL (256)

OCZ Platinum 1024 x 2

Enermax EG495P-VE 485W

Seagate 80 SATA NCQ

Share this post


Link to post
Share on other sites

here's a config I did for r1derbike's 2x1024 + FX-55 when I had it

 

 

 

 

DRAM Configuration Settings:

DRAM Frequency Set - 200 (DRAM/FSB:1/01)

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 2.0

RAS# to CAS# delay (Trcd) - 03 Bus Clocks

Min RAS# active time (Tras) - 05 Bus Clocks

Row precharge time (Trp) - 02 Bus Clocks

Row Cycle time (Trc) - 13 Bus Clocks

Row refresh cyc time (Trfc) - 16 Bus Clocks

Row to Row delay (Trrd) - 03 Bus Clocks

Write recovery time (Twr) - 03 Bus Clocks

Write to Read delay (Twtr) - 02 Bus Clocks

Read to Write delay (Trwt) - 03 Bus Clocks

Refresh Period (Tref) - 3072

Write CAS Latency (Twcl) - Auto

DRAM Bank Interleave - Enabled

 

 

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Auto

DRAM Data Drive Strength - Level 2

Max Async Latency - 8ns

Read Preamble Time - 5.5ns

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(8 Bursts)

 

 

this was on 5/10-2 BIOS. Vdimm voltage @ 2.8v

 

your results may vary, so use this guide as a base starting point, not as the holy grail of these 2x1024 module settings.

Share this post


Link to post
Share on other sites

Thank you Angry Games, for the reply. Memtest is still giving me errors, i see the errors are actually in test 5. Im getting 4 of them. We have run the test several times with differant timings, this last with your suggestions. Do you have any other ideas?

One other thing. I see 6/23 bios is available. Would this be advisable to get on this board at this time?

Share this post


Link to post
Share on other sites

I just got those memory today and I pretty much set everything to auto, I got you the results readings from " A64 tweaker", voltage at stock 2.6 hope this helps:

 

 

setting--------------------------------------------------------------------resulting

 

DRAM Frequency Set - Auto-------------------------------------------200Mhz

Command Per Clock (CPC) - Enable---------------------------------1T

CAS Latency Control (Tcl) - Auto-------------------------------------2.0

RAS# to CAS# delay (Trcd) - AUto resulting-----------------------03 Bus Clocks

Min RAS# active time (Tras) - Auto----------------------------------05 Bus Clocks

Row precharge time (Trp) - Auto-------------------------------------02 Bus Clocks

Row Cycle time (Trc) -Auto--------------------------------------------12 Bus Clock

Row refresh cyc time (Trfc) - Auto------------------------------------14 Bus Clocks

Row to Row delay (Trrd) - 02-----------------------------------------02 Bus Clocks

Write recovery time (Twr) - 02 ---------------------------------------02 Bus Clocks

Write to Read delay (Twtr) - 02--------------------------------------02 Bus Clocks

Read to Write delay (Trwt) - 03--------------------------------------03 Bus Clocks

Refresh Period (Tref) - 1816------------------------------------------1816

Write CAS Latency (Twcl) - Auto--------------------------------------??

DRAM Bank Interleave - Enabled

 

 

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Auto

DRAM Data Drive Strength - Auto------------------------------------????

Max Async Latency - 6ns

Read Preamble Time - Auto-------------------------------------------5.0ns

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - Auto

32 Byte Granularity - Auto

 

Although my processor is different then yours , see if this helps, however I just ran only one pass on memtest, I will be doing an over night tonight hopefully, but no errors there and I ran a few benchy's with no problems thus far.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...