Are there any memory timings posted for OCZ 2gig?

[Sgarv]

Ive been looking for bios memory timings for my specific memory over several forums (including OCZs) and thought i would try this one for answers first. One of the problems ive been seeing is memtest errors on test 6. The memory is new. I just tried switching the sticks from slot 2 and 4 to 1 and 3 looking for error elimination.

Memory in question: OCZ platinum 1024 x 2 , model no. OCZ4002048ELDCPE-K

thx

 

NF4 Ultra-D BIOS 3 / 10

A-64 3200Win

ATI X800XL (256)

OCZ Platinum 1024 x 2

Enermax EG495P-VE 485W

Seagate 80 SATA NCQ

[Angry_Games]

here's a config I did for r1derbike's 2x1024 + FX-55 when I had it

 

 

 

 

DRAM Configuration Settings:

DRAM Frequency Set - 200 (DRAM/FSB:1/01)

Command Per Clock (CPC) - Enable

CAS Latency Control (Tcl) - 2.0

RAS# to CAS# delay (Trcd) - 03 Bus Clocks

Min RAS# active time (Tras) - 05 Bus Clocks

Row precharge time (Trp) - 02 Bus Clocks

Row Cycle time (Trc) - 13 Bus Clocks

Row refresh cyc time (Trfc) - 16 Bus Clocks

Row to Row delay (Trrd) - 03 Bus Clocks

Write recovery time (Twr) - 03 Bus Clocks

Write to Read delay (Twtr) - 02 Bus Clocks

Read to Write delay (Trwt) - 03 Bus Clocks

Refresh Period (Tref) - 3072

Write CAS Latency (Twcl) - Auto

DRAM Bank Interleave - Enabled

 

 

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Auto

DRAM Data Drive Strength - Level 2

Max Async Latency - 8ns

Read Preamble Time - 5.5ns

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - 07 x

32 Byte Granularity - Disable(8 Bursts)

 

 

this was on 5/10-2 BIOS. Vdimm voltage @ 2.8v

 

your results may vary, so use this guide as a base starting point, not as the holy grail of these 2x1024 module settings.

[Sgarv]

Thank you Angry Games, for the reply. Memtest is still giving me errors, i see the errors are actually in test 5. Im getting 4 of them. We have run the test several times with differant timings, this last with your suggestions. Do you have any other ideas?

One other thing. I see 6/23 bios is available. Would this be advisable to get on this board at this time?

[xguy]

I just got those memory today and I pretty much set everything to auto, I got you the results readings from " A64 tweaker", voltage at stock 2.6 hope this helps:

 

 

setting--------------------------------------------------------------------resulting

 

DRAM Frequency Set - Auto-------------------------------------------200Mhz

Command Per Clock (CPC) - Enable---------------------------------1T

CAS Latency Control (Tcl) - Auto-------------------------------------2.0

RAS# to CAS# delay (Trcd) - AUto resulting-----------------------03 Bus Clocks

Min RAS# active time (Tras) - Auto----------------------------------05 Bus Clocks

Row precharge time (Trp) - Auto-------------------------------------02 Bus Clocks

Row Cycle time (Trc) -Auto--------------------------------------------12 Bus Clock

Row refresh cyc time (Trfc) - Auto------------------------------------14 Bus Clocks

Row to Row delay (Trrd) - 02-----------------------------------------02 Bus Clocks

Write recovery time (Twr) - 02 ---------------------------------------02 Bus Clocks

Write to Read delay (Twtr) - 02--------------------------------------02 Bus Clocks

Read to Write delay (Trwt) - 03--------------------------------------03 Bus Clocks

Refresh Period (Tref) - 1816------------------------------------------1816

Write CAS Latency (Twcl) - Auto--------------------------------------??

DRAM Bank Interleave - Enabled

 

 

 

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - Auto

DRAM Data Drive Strength - Auto------------------------------------????

Max Async Latency - 6ns

Read Preamble Time - Auto-------------------------------------------5.0ns

IdleCycle Limit - 256 Cycles

Dynamic Counter - Disable

R/W Queue Bypass - 16 x

Bypass Max - Auto

32 Byte Granularity - Auto

 

Although my processor is different then yours , see if this helps, however I just ran only one pass on memtest, I will be doing an over night tonight hopefully, but no errors there and I ran a few benchy's with no problems thus far.