Jump to content

OCZ VX bios and setting help


Recommended Posts

I can't seem to get my rig (shown below) running good over 230fsb. 3 latency

 

anything above that at any timing voltage or bios and the thing just wants to error and not boot at all

 

 

any help on bios? maybe a version or update that likes this VX mem?

 

Bios settings to help clear it up maybe?

 

I don't understand why this memory will not run over 230 on this board tried 510-2 623-3 and 702-2 bios and they all are the same error at anything over 230 regardless of settings I have read these posts and still can't seem to clear it up

 

Stuff will run at 250 2.0 2-2-8 on my AN8 SLI board with all the exact same components.

 

ANy advice for VX and a San diego

Share this post


Link to post
Share on other sites

I VX did quiet well with the 310p BIOS using the orange slots. The original 510-2 BIOS and yellow slots are okay too. These are the setting I have had success with...

 

GENIE BIOS

 

FSB - 250

LDT/FSB - 3x

LDT Bus Transfer - 16/16

PCI Express - 100MHz

Cool and Quiet - Disabled

CPU VID Startup Value - 1.4v (1.5v)

CPU VID Control - 1.275v (1.225v)

CPU VID Special Control - Above VID x 110% (x 123%)

LDT Voltage Control - 1.3v

Chipset Voltage Control - 1.7v

DRAM Voltage Control - 3.3v

 

DRAM Configuration

 

DRAM Frequency - 200

CPC - Enable

CAS Latency - 2

TRCD - 2

TRAS - 8

TRP - 2

TRC - 10

TRFC - 14

TRRD - 2

TWR - 2

TWTR - 1

TRWT - 2

TREF - 3120, 2560, 1536, 1168, 0908, 0648 (try in this order)

TWCL - Auto

 

DRAM Bank Interleave - Enabled

DQS Skew Control - Auto

DQS Skew Value - 0

DRAM Drive Strength - 8

DRAM Data Drive Strength - Level 1 (4 with the 310p BIOS)

Max Async Latency - 8

Read Preamble Time - 5

Idle Cycle Limit - 128 Clocks (some people have add succes going lower)

Dynamic Counter - Disable

R/W Queue Bypass - 16x

Bypass Max - 07x

32 Byte Granularity - Disable (8 Bursts)

Share this post


Link to post
Share on other sites

I am gonna give 623-2 a whirl and see what gives.

 

Tried so far

510-2

510-2 fix

623 official

702-2

 

Trying 623-2 now. gonna run this one for a good bit and try all the tref's and such to see if I can get it stable. then I am gonna go from the yellow to orange slots and try agian and see.

 

any other thoughts? or just keep trying combos.

 

I have some Mushkin pc4000 redline coming tuesday to see if it is a ram issue. maybe I just got a couple of bad sticks or these just are defective for some reason. I can always rma them.

Share this post


Link to post
Share on other sites

This may be a dumb suggestion but....

 

just wanted to ask if you have a fan blowing on the memory sticks?

 

I have had much better luck with my OCZ utt ch with having a 80mm fan blowing directly over them. Before adding the fan I had problems with test 5 and 8.

Share this post


Link to post
Share on other sites

  • 2 weeks later...

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
 Share

×
×
  • Create New...