PaCoX Posted June 25, 2005 Posted June 25, 2005 Hi, first of all hi everyone, im a newbie in here, and sorry about my english :$ i got 2 modules of Corsair pc3500 rev 1.1 with BH-5 chip and y want to know if there is a guide to configure latencyes in a nforce ultra-d motherboard, with a bus about 250. Plis if someone can help me with this. THANX Sorry for post here and in the sub-forum of motherboard, i dont know where goes. Quote Share this post Link to post Share on other sites More sharing options...
moforila Posted June 25, 2005 Posted June 25, 2005 set your sig up mate, put all your rig details in there. Quote Share this post Link to post Share on other sites More sharing options...
`clipse Posted June 25, 2005 Posted June 25, 2005 can someone post the link to the original jess memory guide.. you know the one that has ever timing and it's effects and settings, color coded with the little star things ** or the AG-remade version of it? EDIT: ok i found the new one link i still prefer jess's original though. Quote Share this post Link to post Share on other sites More sharing options...
Surrept Posted June 25, 2005 Posted June 25, 2005 I just put my take on setting latency and timeings here http://www.dfi-street.com/forum/showthread.php?t=15041 I'm on socketA so i'm not sure how it's done with a64 but the general idea should carry over Quote Share this post Link to post Share on other sites More sharing options...
Mark099 Posted June 25, 2005 Posted June 25, 2005 This should get you started.... GENIE BIOS FSB - 200 LDT/FSB - 5x LDT Bus Transfer - 16/16 PCI Express - 100MHz Cool and Quiet - Disabled CPU VID Startup Value - 1.50v (1.4v w Venice) CPU VID Control - 1.325v (1.275v w Venice) CPU VID Special Control - Above VID x 113% (110% w Venice) LDT Voltage Control - 1.2v Chipset Voltage Control - 1.6v DRAM Voltage Control - 3.2v DRAM Configuration DRAM Frequency - 200 CPC - Enable CAS Latency - 2 TRCD - 2 TRAS - 8 TRP - 2 TRC - 10 (TRC = TRAS + TRP) TRFC - 14 (TRFC = TRC + 4) TRRD - 2 TWR - 2 TWTR - 1 TRWT - 2 TREF - 3120, 2560, 1536, 1168, 0908 (try in this order) TWCL - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 8 DRAM Data Drive Strength - Level 1 Max Async Latency - 8 Read Preamble Time - 5 Idle Cycle Limit - 128 Clocks Dynamic Counter - Disable R/W Queue Bypass - 16x Bypass Max - 07x 32 Byte Granularity - Disable (8 Bursts) Quote Share this post Link to post Share on other sites More sharing options...
kaltmond Posted June 25, 2005 Posted June 25, 2005 Can someone tell me if my 3500C2 is right or not. I have one 3200LL and one 3500C2, both BH5, but why the CPUZ says it is only 2.5-3-3-8@200? :confused: Quote Share this post Link to post Share on other sites More sharing options...
Mark099 Posted June 25, 2005 Posted June 25, 2005 Can someone tell me if my 3500C2 is right or not. I have one 3200LL and one 3500C2, both BH5, but why the CPUZ says it is only 2.5-3-3-8@200? :confused: Sometimes, SPD settings will be different for an A64 system. Other times, the manufacture will make them that way to minimize issues (with loose timings) on the first boot. Either way, you can always change the settings in the BIOS. Quote Share this post Link to post Share on other sites More sharing options...
dfidiot Posted June 26, 2005 Posted June 26, 2005 If your 3200LL are v1.1, those are bh-5. You know your 3500's are. Don't worry about cpuz. Quote Share this post Link to post Share on other sites More sharing options...
dfidiot Posted June 26, 2005 Posted June 26, 2005 DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - 8 DRAM Data Drive Strength - Level 1 I would leave all these at "auto". Quote Share this post Link to post Share on other sites More sharing options...
Prostock62 Posted June 26, 2005 Posted June 26, 2005 Hi, first of all hi everyone, im a newbie in here, and sorry about my english :$ i got 2 modules of Corsair pc3500 rev 1.1 with BH-5 chip and y want to know if there is a guide to configure latencyes in a nforce ultra-d motherboard, with a bus about 250. Plis if someone can help me with this. THANX Sorry for post here and in the sub-forum of motherboard, i dont know where goes. First can you make a sig with your specks and save it to your user CP?Its hard to give you advice if we dont know what your running,or what your running at.If you install CPUZ it will give you the spd setting on your memory.Set it to that and start overclocking slowly and make adjustments to volts and memory timeing as needed.Iam running my Corsair at stock Spd setting overclocked up to 2.6 without haveing to looseing the timeing.Everybodys setup will bring diffrent results.The 3500 has a Spd timeing of a stick of 3200.Thats what it will show up as in cpuz.The memory will list as 3500 but the timeing will be of the 3200. http://img48.echo.cx/img48/823/60et.jpg Quote Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.