Jump to content
Sign in to follow this  
xms

06/18 NF4 BIOS Out

Recommended Posts

Um ya if thats on AIR imma throw my 4000+ Sandy out the window.

 

 

Umm....i can see your Sandy flying out of the window now...

 

I'm running 2x Tornado's + Hyper6

 

 

Here's my first attempt a while back @ 3.0ghz with my mem on a divider:

http://www.sysxtreme.com/showthread.php?t=1130

 

2nd attempt with new OCZ ram 1:1 and processor @ 3.1ghz

http://www.sysxtreme.com/showthread.php?t=1498

 

 

Most of the time i run at 3.0ghz because it seems more stable than 3.1ghz (even tho it completed a 7hr prime).

Share this post


Link to post
Share on other sites

I'm just hours away from a complete reinstall, from scratch everything, with this memory, should I update my bios?

 

corsair7yk.jpg

 

I believe it is XMS-PC3200C2 Rev1.2/2.2 (2-3-3-6-1T) which means Winbond CH-6..

 

check sig for timings now, it's all set to auto in bios.

Share this post


Link to post
Share on other sites

Sound good, sound good...

 

I'm tempted to try but it's still too new for me. I don't have a backup bios or bios saviour so I don't dare try anything until a week to reduce the chance the will be a major problem that goes undetected

Share this post


Link to post
Share on other sites
Hi guys,

 

Couldnt see a thread in this section about this, so i thought i better let you all know.

 

I've flashed with it, and it looks good so far (it hasn't hindered my overclock at all).

 

Available here:

 

http://oskarwu.myweb.hinet.net/dfi/betabios/N4D618-1.zip

http://oskarwu.myweb.hinet.net/dfi/betabios/N4D618-2.zip

http://oskarwu.myweb.hinet.net/dfi/betabios/N4D618-3.zip

 

Or mirrored here:

 

http://www.sysxtreme.com/showthread.php?p=24763

 

Bios 6/15 or 6/18 problem,you try this setting

 

http://img72.echo.cx/img72/3371/bios5109ff.jpg

 

 

http://www.dfi-street.com/forum/showthread.php?t=14536

Share this post


Link to post
Share on other sites

I just tried it and it works great. I also moved my bh-5 memory to the yellow slots and it works just dandy. No problems so far. I am running the -1 Bios. Just had to change the memory voltage to 3v for my memory in order for it to be stable.

Share this post


Link to post
Share on other sites

Running the 618-3 now... sweet so far. I tried the -2 variant and the 3/10 (-3) ram table for TCCD or TCC5 just runs better for me.

 

I got errors in the -2 variant on OCCT and stable on the -3 with the same settings.

 

O well.

Share this post


Link to post
Share on other sites

Much worse for me. In 510-2 I was extremely stable, but with 618-2, games freeze within 30 minutes. I will try 618-3 first, but if that doesn't work, back to 510-2 I go

Share this post


Link to post
Share on other sites

I don't know if any of the rest of you experienced this, but when i flashed, it put the setting "Dram +0.03 v if not 3.2v" (or whatever) to Enabled.

 

This caused my rig to be unstable coz my TCCD totally hates anything more than 2.7v for some reason.

Share this post


Link to post
Share on other sites
Hi guys,

 

Couldnt see a thread in this section about this, so i thought i better let you all know.

 

I've flashed with it, and it looks good so far (it hasn't hindered my overclock at all).

 

Available here:

 

http://oskarwu.myweb.hinet.net/dfi/betabios/N4D618-1.zip

http://oskarwu.myweb.hinet.net/dfi/betabios/N4D618-2.zip

http://oskarwu.myweb.hinet.net/dfi/betabios/N4D618-3.zip

 

Or mirrored here:

 

http://www.sysxtreme.com/showthread.php?p=24763

Umm, I was originally running the 615 BIOS, and I flashed to the 618-2 BIOS, and everything was OK, except for the internet. I made sure that one setting was set to Pin Strap, but still no internet. Flashed back to 615, and WTF? Still no internet. I'm on 310 right now and it has been the most stable for me so far.

Share this post


Link to post
Share on other sites

my $0.02

 

if you have TCCD mem, like OCZ Rev2 plats etc...try 618-3 !

 

Seems to work very well !

 

Btw. i NEVER had any problems with non working devices like USB/LAN etc....also..you SHOULD not use the Marvell/Gigabit LAN anyway, it blows chunks ! (Uses far more resources and CPU than the NV LAN).

 

Also...i never ever (since i have this board) had to enter my MAC address anywhere.

Share this post


Link to post
Share on other sites
my $0.02

 

if you have TCCD mem, like OCZ Rev2 plats etc...try 618-3 !

 

Seems to work very well !

 

Btw. i NEVER had any problems with non working devices like USB/LAN etc....also..you SHOULD not use the Marvell/Gigabit LAN anyway, it blows chunks ! (Uses far more resources and CPU than the NV LAN).

 

Also...i never ever (since i have this board) had to enter my MAC address anywhere.

 

 

You can try this bios 6/15-3 or 6/18-3 setting here it's not running

 

bios5109ff.jpg

 

This is bios 5/10-3 setting not problem

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...