Jump to content

nf3 and nero 6 problem


Recommended Posts

last bios 04/05/05 , driver nvidia 5.10 , last nero 6.6.0.13, xp pro +sp2 in raid 0

 

unable to burn dvd with my lg 4082b

 

log of nero show dma off for all ide drive

 

but all ok pata controller nf3250 in hardware tab

 

suggestions ?

 

thanx

Share this post


Link to post
Share on other sites

  • Replies 35
  • Created
  • Last Reply

Top Posters In This Topic

Look for a newer firmware version for you LG, try other clables or master/slave setup, Force UDMA 2 for your burner if it's a UDMA4 or 5 unit (it will still be more than enough and solves problems with some drives. But first of all, I'd try to go to add/remove, select nvidia drivers and remove only nvidia SW IDE drivers to try the default windows ones, as the nvidia are know to cause trouble with some setups (including mine...). Good luck!

Share this post


Link to post
Share on other sites

  • 3 weeks later...

tried with 2 dvd-r (lg 4082b and btc double layer)

nero 6.6.0.13 and nti cd dvd maker platinum 7.

 

my sistem is as in signature ....

 

nero show an error "unable to write disk at once"

nti error code 1014

 

please help me !!!

Share this post


Link to post
Share on other sites

Removing the controller from device manager allows the OS to reinstall the controller and turn all of the features back on.

 

Something caused the OS to downgrade the controller. Normally this happens when there are a lot of CRC errors.

 

Keep an eye on it.

UPDATE:

 

removed pata controller from device manager, reboot and now 2 dvd-r burned ok

 

stay tuned for news problem again (i hope no)

Share this post


Link to post
Share on other sites

Removing the controller from device manager allows the OS to reinstall the controller and turn all of the features back on.

 

Something caused the OS to downgrade the controller. Normally this happens when there are a lot of CRC errors.

 

Keep an eye on it.

 

 

ok, but the problem is cheap dvd-r or defeating ata cables ?

 

 

thanx

Share this post


Link to post
Share on other sites

There's no way to tell yet. If the problem shows up again you'll need to make a cable change then reload the controller to start fresh. I ran into this problem a few years ago when I installed a new CD burner. It turned out the burner was defective in my case. Others have changed the cable or flashed the BIOS on the drive to correct the problem.

ok, but the problem is cheap dvd-r or defeating ata cables ? thanx

Share this post


Link to post
Share on other sites

  • 1 month later...

again problem , now trying with nti cd/dvd maker platinum

 

prior error and no burning, after i uninstall pata controller on device manager,

 

and i burn 1 dvd and after again error

 

see the logfile

 

 

========== BEGIN OF LOG ==========

 

NTI CD & DVD-Maker 7.0.0.35 (SKU-22710238888)

Start Time: Tuesday, July 12, 2005, 10:55:14PM

 

Processor Architecture: INTEL

Processor Type: INTEL PENTIUM

Processor Level: 15

Microsoft Windows XP version 5.1 Service Pack 2 (Build 2600)

Memory in use: 37%

Total physical memory: 523 MB

Total free physical memory: 328 MB

Total paging file: 1540 MB

Total free paging file: 1380 MB

Total virtual memory: 2097 MB

Total free virtual memory: 1998 MB

 

CD Layout: Data DVD

Disc Format: DVD-ROM

File System: Joliet

Bootable CD: Yes

Total Data Blocks: 397464

 

CD-Recorder: HL-DT-ST DVDRAM GSA-4082B (D:)

Firmware Version: A208

Disc Media: DVD-R

Free Disc Blocks: 2298496

Test: No

Write Speed: 4x

Write Method: Track-At-Once

Close Disc: No

Leave Session Open: No

 

Error Code: 1014

CDB: 43 00 00 00 00 00 AA 00 0C 00 00 00

SenseKey:00 ASC:00 ASCQ:00

 

Finish Time: Tuesday, July 12, 2005, 10:56:52PM

 

========== END OF LOG ==========

Share this post


Link to post
Share on other sites

log events on xp show this errors (italian language)

 

Tipo evento: Errore

Origine evento: Cdrom

Categoria evento: Nessuno

ID evento: 11

Data: 02/08/2005

Ora: 22.26.05

Utente: N/D

Computer:

Descrizione:

Il driver ha rilevato un errore del controller su DeviceCdRom0.

 

Per ulteriori informazioni, consultare la Guida in linea e supporto tecnico all'indirizzo http://go.microsoft.com/fwlink/events.asp.

Dati:

0000: 00680003 00b80001 00000000 c004000b

0010: 00000101 00000000 00000000 00000000

0020: 0ff07000 00000000 000aae48 00000000

0030: ffffffff 00000003 84000040 00000002

0040: 120a2000 40000248 00000000 0000000a

0050: 00000000 822fc7b8 00000000 8226fc68

0060: 00000002 0001fe0e 01000028 00000efe

0070: 00000020 00000000 00040070 0a000000

0080: 00000000 0000023e 00000000 00000000

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now

×
×
  • Create New...