Socket 939 Discussion Thread

[Guest viking]

so i can close my prime 95 window ..cos i would hate to do it all ower again

since i only have 1 comp

[Praz]

That's more like the readings we're used to seeing. It's also a good example of why I use programs that read the sensors. Even though we don't' know the accuracy the delta is useful.

[soundx98]

Go ahead and close it Viking.

All we need are separate shots and 3D03, 3D05, and 3D06 with Everest 2.2 or higher in one of them.

Then just use the template.

[Guest viking]

DFI LANPARTY nF4 SLI-D (623 BIOS)

 

AMD 3700+ San Diego KAB3E 0547 GPMW XP120 120mm TT

 

2x512 OCZ 4000VX Gold

 

Sapphire X1900XTX, catalyst 6.7

 

2x250gb Maxtor Diamondmax 10 16mb

 

2xNec 3520

 

OCZ 520w powerstream

 

*

 

==========

 

[b]Genie BIOS Settings:[/b]

[color=red]

FSB Bus Frequency.............................  -  300

LDT/FSB Frequency Ratio.......................  -  auto

CPU/FSB Frequency Ratio.......................  -  x10

PCI eXpress Frequency.........................  -  100Mhz



CPU VID StartUp Value.........................  -  startup



CPU VID Control...............................  -  1.350v

CPU VID Special Control.......................  -  113%

LDT Voltage Control...........................  -  1.30v 

Chip Set Voltage Control......................  -  1.60v

DRAM Voltage Control..........................  -  3.20v[/color]



[b]DRAM Configuration Settings:[/b]

[color=red]

DRAM Frequency Set............................  -  166=RAM/FSB:5/6

Command Per Clock (CPC).......................  -  Enable 

CAS Latency Control (Tcl).....................  -  02

RAS# to CAS# delay (Trcd).....................  -  02

Min RAS# active time (Tras)...................  -  05

Row precharge time (Trp)......................  -  02

Row Cycle time (Trc)..........................  -  07

Row refresh cyc time (Trfc)...................  -  15

Row to Row delay (Trrd).......................  -  00

Write recovery time (Twr).....................  -  02

Write to Read delay (Twtr)....................  -  02

Read to Write delay (Trwt)....................  -  02

Refresh Period (Tref).........................  -  3120 Cycles

DRAM Bank Interleave..........................  -  Enabled



DQS Skew Control..............................  -  increase skew

DQS Skew Value................................  -  255

DRAM Drive Strength...........................  -  7

DRAM Data Drive Strength......................  -  Auto

Max Async Latency.............................  -  0.8

DRAM Response Time............................  -  fasest

Read Preamble Time............................  -  0.6

IdleCycle Limit...............................  -  16 Cycles

Dynamic Counter...............................  -  Enable

R/W Queue Bypass..............................  -  16 x

Bypass Max....................................  -  07 x

32 Byte Granularity...........................  -  Disable(4 Bursts)

[/color]

 

 

==========

 

 

Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20:

 

http://usera.imagecave.com/viking/3ghz3hz.JPG

 

 

3dMark2003:

 

http://usera.imagecave.com/viking/3dmark03_1.JPG

 

3dMark2005:

http://usera.imagecave.com/viking/3dmark05.JPG

 

3dMark 2006:

http://usera.imagecave.com/viking/3dmark06_1.JPG

 

 

 

==========

 

 

 

short description:

3700+ SD @ 300x10 1.49v 250fsb 2 2 5 2

 

edit: now whit stepping code

[Guest viking]

could some pls chek if i got it right

i lost the stepping code but ill get it in 2 weeks when ill be mouting my first water

 

whats that about my sig ? aint my sig good enogh ?

[soundx98]

looks to me like you've met every requirement except the stepping of cpu

 

Complete detailed specs, including voltages, timings, bios version, exact model of hardware and exact stepping of cpu etc

 

so you can wait a couple weeks until you remove the XP120 and then complete the "stepping" and the post above can be moved over.

 

If you want to do it sooner just fill in the correct stepping of course.

Really nice work Viking. like those timings

 

Your sig is fine.

There is a custom sig request thread too if you'd like some help.

 

EDIT: Missing Everest Read as well.

EDIT 2: Geez you guys are fast.

[oc newbie]

Viking looks like you dont have everest read in one of the other pics. Just rerun one of the 3d marks and include everest read benchmark and then it's good to go. Nice job on that one, You should put a link to your database post over in the GGG thread and become a member.

[likewhoa]

missing two of the everest benchmarks, you need all 3 of the memory results showing.

have the read,write & latency showing, put one on each 3dmark starting from 3dmark03.

 

Your short description should be like..

 

FSBxMultiplier @ speed, CPU voltage/ CPU overvolt % or just total Vcore

 

i.e 900x10 @ 9000Mhz 1.375v <-- imagen that.. but you get the picture.

and don't post it here but in the 939 OCDB. then edit if a moderator or another user request.

[Praz]

Unless the requirements have recently changed, the only Everest bench needed is memory read.

[soundx98]

Thanks Praz, viking PM if you have any questions

[likewhoa]

hey soundx98 you sell all your pc parts?

[soundx98]

PM me regarding what you were looking at