oc newbie Posted July 24, 2006 Posted July 24, 2006 DFI LANPARTY nF4 ultra-d modded to sli-d (704-2BTA BIOS) AMD opteron 146 (cab1e 0614epaw) xp-90 air cooled 2x1024MB OCZ PC4000GOLDXTC(OCZ5002048ELGEGXT-K) EVGA GeForce 6800GS, 500/1200 81.98 drivers 320GB Western Digital 7200RPM SATA hdd 250GB Western Digital 7200RPM SATA hdd Lite-on 16xDVD Burner Ocz Modstream 520w Power Supply * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 315 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - auto CPU VID Control............................... - 1.400 CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v+enable[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - normal level 3 DRAM Data Drive Strength...................... - level 2 Max Async Latency............................. - 8ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003 + Everest: 3dMark2005: 3dMark 2006: ========== short description: air cooled with lapped xp-90/vc-re cooled chipset 315x10 @ 3150Mhz, 1.40+110% = 1.54 cpu voltage 262fsb @ 3-4-8-4 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
Evil-Fruits|R4z Posted July 24, 2006 Posted July 24, 2006 DFI LANPARTY nF4 SLI-DR Venus ( 4/6/2006 BIOS) AMD Opteron 165 dual core - CCB1E 0550 VPMW 2x1024MB G.SKILL HV4000 (F1-4000BIU2-2GBHV) MSI GeForce 7800GTX, 480/1300 91.31 drivers 2x36GB Western Digital Raptor 10,000RPM SATA hdd - RAID 0 & Maxtor Diamondmax 250GB SATA II Pioneer DVR-111DBK Seasonic S-12 500W Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.350v CPU VID Control............................... - 1.500 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 6 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3684 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Off DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7 DRAM Data Drive Strength...................... - Level 3 (reduce 15%) Max Async Latency............................. - 7.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 4.0 ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disabled(8 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.35 + Everest Ultimate Edition 2006: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 300x9 @ 2700Mhz, 1.475V 3-3-2-6 @ 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
uncle john Posted July 25, 2006 Posted July 25, 2006 DFI LANPARTY nF4 Ultra-D (7/04-2bta BIOS) AMD Opteron 144 CAB1E 0614EPCW 2x1GB OCZ PC4000EB (OCZ5001024EBPE-K) BFG 7950GT OC, (stock) 320GB Seagate Barracuda 7200.10 ST3320620AS SATA hdd Antec Neo HE 550 ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.5 CPU VID Control............................... - 1.425 CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.50v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 7 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 9 Bus Clocks Row refresh cyc time (Trfc)................... - 12 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Normal 4 (Level 8) DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - 8 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6 ns IdleCycle Limit............................... - 128 Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== short description: 334x9 @ 3006Mhz, 1.57v 3-3-7-2 @ 2.50v vdimm Share this post Link to post Share on other sites More sharing options...
lackobreath Posted July 25, 2006 Posted July 25, 2006 DFI LANPARTY UT nF4 SLI-DR eXpert (Official 04/06/2006) AMD Opteron 165 CCBBE 0610DPMW Thermalright XP-120 w/ Silverstone FM121 2x1024MB OCZ PC-4000 Gold XTC (OCZ5002048ELGEGXT-K) Sapphire Radeon X850XT w/ Zalman VF900, 560/1200 Catalyst 6.6 drivers 2 x 250GB Western Digital RE SATAII Plextor PX-712A OCZ Gamextream 600 ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.500v CPU VID Special Control....................... - + 102.4% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.58v DRAM Voltage Control.......................... - 2.71v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 11 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7 DRAM Data Drive Strength...................... - 2 Max Async Latency............................. - 8.0 DRAM Response Time............................ - Fast Read Preamble Time............................ - 6.0 IdleCycle Limit............................... - 128 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: Everest 2.20.405 ========== short description: 334x9 @ 3006Mhz, 1.500v+102.4%=1.536v 3-4-3-8 @ 2.71v vdimm Share this post Link to post Share on other sites More sharing options...
farksy Posted July 30, 2006 Posted July 30, 2006 Dfi Lanparty Ut nF4-D Rev A.00 (Official 06/23/2006) Amd Opteron 146 CABYE 0540 FPMW Scythe Ninja Plus 2x512Mb Ocz PC-3200 EL Plat Rev. 2 (TCC5s) Xpertvision 6600 DDR3 [Forceware 84.21 , 440/1200] 80Gb Maxtor Diamondback P-ATA 32Gb Seagate 7200.10 SATA Creative Sb Live! 5.1 BenQ Dw 1640 Verudium Vortex 430W ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x10 PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - Default [1.4V] CPU VID Control............................... - 1.475v CPU VID Special Control....................... - + 104% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.70v DRAM Voltage Control.......................... - 2.80v [+ 0.3V][/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200= RAM:FSB = 01:01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 8 DRAM Data Drive Strength...................... - 3 Max Async Latency............................. - 8.0 DRAM Response Time............................ - Fast Read Preamble Time............................ - 6.0 IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 7 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + Everest Latency + Cpu-Z: http://i3.photobucket.com/albums/y76/farks...stCpuZPrime.jpg 3dMark2003 + Cpu-Z: http://i3.photobucket.com/albums/y76/farksy/03-1.jpg 3dMark2005 + Cpu-Z: http://i3.photobucket.com/albums/y76/farksy/05-1.jpg 3dMark 2006 + Cpu-Z: http://i3.photobucket.com/albums/y76/farksy/06.jpg ========== short description: 300x10 @ 3004Mhz, 1.500v+104%=1.488v 1:1 @ 2.5-4-3-5 @ 2.84v vdimm Share this post Link to post Share on other sites More sharing options...
racewayzx Posted July 30, 2006 Posted July 30, 2006 DFI LANPARTY nF4 Ultra-D (7/04-2BTA BIOS) AMD Opteron 165 0610dpmw 2x1024MB Muskin XP4000 Redline Evga 7900gt KO SC, 580/1580 91.31 drivers 2x 80g Seagate 7200.9 SATA hdd in raid 0 & Maxtor 200g SATA hdd BenQ 1650v DVDrom & Plextor PX-760A DVD burner OCZ 700w gamerxstream ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - 2.5 CPU/FSB Frequency Ratio....................... - 9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.5 CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:3/4 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 08 Bus Clocks Row refresh cyc time (Trfc)................... - 15 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 10.0 DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 IdleCycle Limit............................... - 016 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 3 mem write: http://i110.photobucket.com/albums/n87/rac...zx/Screen03.jpg 3dMark2003 + Everest 3 mem copy: http://i110.photobucket.com/albums/n87/rac...zx/Screen04.jpg 3dMark2005 + Everest mem latency: http://i110.photobucket.com/albums/n87/rac...zx/Screen05.jpg 3dMark 2006 + Everest mem read + A64 info: http://i110.photobucket.com/albums/n87/rac...zx/Screen06.jpg ========== short description: 334x9 @ 3006Mhz, 1.65v 3-3-2-8 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
bcbooter Posted July 31, 2006 Posted July 31, 2006 DFI LANPARTY nF4 ULTRA-D (6/23/05 bios) AMD Opteron 165 0550vpmw 2x1024MB G.SKiLL HZ SERIES EVGA GeForce 7800GT, 507/1295 nv84.20 3x80gb hitachi dekstar raid 0 rosewill cd rom ocz powerstream 520w Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.475 CPU VID Special Control....................... - 113% LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150 (DRAM/FSB:3/04) Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - AUTO Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - LEVEL 8 DRAM Data Drive Strength...................... - LEVEL 1 Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - 5.5 NS IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: http://img122.imageshack.us/img122/1513/pic1po5.jpg 3dMark2003 + EVEREST: http://img122.imageshack.us/img122/4145/pic2mc1.jpg 3dMark2005: http://img113.imageshack.us/img113/3715/pic3je6.jpg 3dMark 2006: http://img156.imageshack.us/img156/7792/pic4hc2.jpg ========== short description: 334X9 1.66V ram DDR500 3-4-4-8 2.7V Share this post Link to post Share on other sites More sharing options...
likewhoa Posted August 8, 2006 Posted August 8, 2006 DFI LANPARTY nF4 SLI-DR (7/04-2BTA BIOS) AMD Opteron 165 CCBBE 0617FPMW 2x1024MB Munskin Redline XP4000 (991493) EVGA GeForce 7900GTX, 650/1600 91.33 drivers 150GB Western Digital Raptor X WD1500AHFD 2x 400GB Seagate Barracuda 7200.9 ST3400633AS Khypermedia DVD+RW 8x4x12 OCZ PowerStream 520W Power Supply Swiftech H20-220 APEX ULTRA & MCW60 VGA Block ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 335 LDT/FSB Frequency Ratio....................... - x 3.0 CPU/FSB Frequency Ratio....................... - x 9.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.425v CPU VID Special Control....................... - 110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 03 RAS# to CAS# delay (Trcd)..................... - 03 Min RAS# active time (Tras)................... - 01 Row precharge time (Trp)...................... - 02 Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 00 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Increase Skew DQS Skew Value................................ - 221 DRAM Drive Strength........................... - normal4 DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 05 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 335x9 @ 3015Mhz, 1.425v +110% 3-3-2-1 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
Kingfisher Posted August 9, 2006 Posted August 9, 2006 DFI LANPARTY UT nF4 SLI-DR Expert(12/7/06 BIOS) AMDAthlon64X24400+(89W)1MBL2 Crucial Technology Ballistix 1GB (2 x 512MB)pc3200 2 x eVGA 6600GT, 490/1310 91.30 drivers HITACHI Deskstar T7K250 x 2/Raid 0 320GBs Lite-0n SOHW-1633s dvd burner Hiper Type-R 580w * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 264 LDT/FSB Frequency Ratio....................... - auto CPU/FSB Frequency Ratio....................... - x 11 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - auto CPU VID Control............................... - 1.400v CPU VID Special Control....................... - Above VID * 104.8 LDT Voltage Control........................... - 1.40v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.71v DRAM Configuration Settings: DRAM Frequency Set............................ - 180=RAM/FSB:09/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 02 Bus Clocks Min RAS# active time (Tras)................... - 06 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 09 Bus Clocks Row refresh cyc time (Trfc)................... - 12 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 2064 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z : 3dMark2003: 3dMark2005: 3dMark2006: http://img.photobucket.com/albums/v335/Gem...rk06everest.jpg ========== short description: 264x11 @ 2.904, 1.400v* 104.8% 2.5-2-3-6 @ 2.71v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted August 11, 2006 Posted August 11, 2006 DFI LANPARTY nF4 SLI-DR (406 BIOS) AMD X2 3800+ dual core LDBFE 0609 XPMW 2x1024MB Crucial Ballistix Z503 PowerColor X1900xtx , 675-783 6.7 drivers 74GB Western Digital Raptor 10,000RPM SATA hdd's in RAID0 - Windows 64bit NEC 3550a DVD Pc Power and Cooling 1Kw Power Supply DangerDen = TDX + Maze4 + BIX2 + DDC-12v + 38 tubing * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 270 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Auto CPU VID Control............................... - 1.425 CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.70v + .03v (enabled)[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 3 Row Cycle time (Trc).......................... - 9 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3072 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Lev6 DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 8 DRAM Response Time............................ - normal Read Preamble Time............................ - 5.5 IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + MBM + A64Tweaker : http://img157.imageshack.us/img157/4096/untitled1up6.jpg 3dMark2003 + CPU-Z + MBM + A64Tweaker + Everest Writes : http://img225.imageshack.us/img225/2476/untitled2kw1.jpg 3dMark2005 + CPU-Z + MBM + A64Tweaker + Everest Latency : http://img225.imageshack.us/img225/834/untitled3uv8.jpg 3dMark 2006 + CPU-Z + MBM + A64Tweaker + Everest Reads : http://img90.imageshack.us/img90/8490/untitled4um7.jpg ========== short description: 270x10 @ 2700Mhz 3-3-8-3 @ 2.6 + 03v vdimm Share this post Link to post Share on other sites More sharing options...
Traveller Posted August 11, 2006 Posted August 11, 2006 DFI LanpartyUT nF4 Ultra-D (SLI Mod)(BIOS 0406bta) AMD Athlon64 X2 3800+ Manchester[E4] 2x1024MB Corsair TWINX2048-3200C2PT 2x Gigabyte 6600GT 128Mb, 560/1060 91.33 drivers 2x Hitachi 250 GB SATA II (SATA 1/2) 1x WD Caviar SE16 400GB SATA I (SATA 3) NEC ND-2510A DVD Burner IDE 1/0 Asus DRW 1608P DVD Burner IDE 1/1 OCZ Modstream 520W Danger Den TDK block and pump (3/8" ID tubing) Dell 1905FP LCD Monitor Hardcano 13 (4 fans and 2 t/c's-waterblock & case) Kworld VS-LTV883D Xpert video capture card (PCI-2) * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x10.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.500V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Auto CAS Latency Control (Tcl)..................... - 03 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 08 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - 13 Bus Clocks Row refresh cyc time (Trfc)................... - 16 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Level4 (Reduce 00%) Max Async Latency............................. - 10.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 08.0 Nano Seconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z 1.35: http://img145.imageshack.us/img145/4293/pr...01secpuzsh6.jpg 3dMark2003: http://img19.imageshack.us/img19/7253/3dmark03ur5.jpg 3dMark2005: http://img19.imageshack.us/img19/8564/3dmark05wx7.jpg 3dMark 2006: http://img19.imageshack.us/img19/7605/3dmark06hk0.jpg Everest 2.20: http://img19.imageshack.us/img19/3383/everest22db1.jpg ========== short description: 250x10 @ 2500Mhz, 1.500V 3-3-8-3 @ 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
Guest BFG Posted August 12, 2006 Posted August 12, 2006 DFI LANPARTY nF4 SLI-DR (7/04-2BTA BIOS) AMD 3700+ San Diego 2x1024MB G.Skill HZ PC4000 eVGA GeForce 7800 GTX 512, 590/1750 81.98 drivers 200 Gig Seagate IDE, 160 Gig SATA Seagate NEC Black 16x DVD Burner Enermax Whisper 535w Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - 3.0x CPU/FSB Frequency Ratio....................... - x10 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.475 CPU VID Special Control....................... - 104% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Disable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 8 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3684 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - 7 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Fast Read Preamble Time............................ - 5.0ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: Everest 2.20: ========== short description: 300x10 @ 3000Mhz, 1.475 x 104% 3-4-4-8 @ 2.60v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now