Angry_Games Posted August 17, 2005 Posted August 17, 2005 DFI LANPARTY nF4 SLI-DR NF4 SLI-DR - 7/04-2 BigToe BIOS AMD Athlon64 X2 4400+ DualCore 4x512MB Centon Advance PC3200 (TCCD) Nvidia 6800GT PCI-Express , 415/1071 76.41 drivers WD Raptor 36GB 10,000RPM SATA hdd (8MB cache) ASUS CD-S520/A5 Black IDE CD-ROM Drive OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail Danger Den TDX Athlon64 (754/939) copper waterblock Danger Den CSP-MAG 12v pump Danger Den Black Ice Xtreme 120mm radiator Danger Den polyethylene 5.25" bay resevoir Danger Den Zerex water additive (4oz. bottle) Danger Den Tygon tubing * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 260 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x 10.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.350v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.00v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 5.5 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 04 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/nf4/X...12_260x10-1.jpg 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 260x10 @ 2600Mhz, 1.350v + 113% 2.5-4-8-3 @ 3.0v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted August 17, 2005 Posted August 17, 2005 DFI LANPARTY nF4 SLI-DR NF4 SLI-DR - 7/04-2 BigToe BIOS AMD Athlon64 4000+ San Diego 2x1024 OCZ Gold PC4000 (OCZ5002048ELGE-K) Chaintech 2*6600GT SLI , 560/1114 77.72 drivers 2* WD Raptor 36GB 10,000RPM SATA hdd (8MB cache) - RAID-0 ASUS CD-S520/A5 Black IDE CD-ROM Drive Skyhawk 570w 24-pin ATX power supply Danger Den TDX Athlon64 (754/939) copper waterblock Danger Den CSP-MAG 12v pump Danger Den Black Ice Xtreme 120mm radiator Danger Den polyethylene 5.25" bay resevoir Danger Den Zerex water additive (4oz. bottle) Danger Den Tygon tubing 2x Danger Den 'Low Profile' Acetal Maze4 GPU waterblock * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x 11.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.375v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 09 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/nf4/2...gb-PC4000-1.jpg 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 250x11 @ 2750Mhz, 1.375v + 113% 3-4-9-4 @ 2.9v vdimm Share this post Link to post Share on other sites More sharing options...
thecoomar Posted August 21, 2005 Posted August 21, 2005 DFI LanParty NF4 Ultra-D 7/04-2 BIOS Venice 3000+ LBBLE 0519GPIW Enermax 485W Noisteaker Mushkin Blue C2 (BH-5 UTT) 2x512 Asus X700le Stock Cooler (i have an XP-120 that I will install later this week) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Genie BIOS Settings: FSB Bus Frequency - 290 LDT/FSB Frequency Ration - 3x CPU/FSB Frequency Ratio - x9.0 PCI eXpress Frequency - 105Mhz CPU VID StartUp Value - 1.5 CPU VID Control - 1.5v CPU VID Special Control - Auto LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.3v DRAM Configuration Settings: DRAM Frequency Set - 166 (DRAM/FSB:5/06) Command Per Clock (CPC) - 1T CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 2 Min RAS# active time (Tras) - 6 Row precharge time (Trp) - 2 Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 12 Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 01 Bus Clocks Read to Write delay (Trwt) - 01 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - 5 (Will pass memtest at 1 but crashes in games) DRAM Bank Interleave - Enabled DQS Skew Control - On DQS Skew Value - 0 DRAM Drive Strength - 8 (I used 6 for the last couple months) DRAM Data Drive Strength - 1 Max Async Latency - 7.0ns Read Preamble Time - 5.0ns IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ prime95-10 hours +cpu-z (2) +3dmark01 +3dmark03 +screenshot of 3dmark05 http://www.filefarmer.com/coomar/DFIprime.JPG 3dmark05 aquamark3 everest read http://www.filefarmer.com/coomar/everest_read.JPG everest write +A64 Tweaker http://www.filefarmer.com/coomar/everestwrite_236.JPG everest latency +A64 Tweaker http://www.filefarmer.com/coomar/everestlatency_236.JPG Share this post Link to post Share on other sites More sharing options...
cwa4me Posted August 22, 2005 Posted August 22, 2005 AMD Athlon 64 FX-55 Claw Hammer Socket 939 Processor Model#:ADAFX55DET5AS Stepping:AAA2C0435UPCW DFILanparty NF4 Sli-dr 6/23-3 Bios: http://www.newegg.com/Product/Product.asp?...N82E16813136157 1- Seagate Barracuda 250g sata 7200rpm: http://www.newegg.com/Product/Product.asp?...N82E16822148065 2x512MB OCZ EL Platinum revision 2 memory: http://www.newegg.com/Product/Product.asp?...N82E16820146890 evga 256-p2-n376-AX Geforce 6800GT 256MB 256-bit GDDR3 PCI-Express X16 Vid. card 7.1.2.5 drives-409/1100: http://www.newegg.com/Product/Product.asp?...N82E16814130215 PSU: Antec True Power II 480w sli: http://www.newegg.com/Product/Product.asp?...N82E16817103929 Heatsink: xp-90c,Thermalright: http://www.newegg.com/Product/Product.asp?...N82E16835109122 Heatsink fan: Vantec Tornado 92mm (119 cfm): http://www.newegg.com/Product/Product.asp?...N82E16811999613 * * ========== Genie BIOS Settings: FSB Bus Frequency - 215 LDT/FSB Frequency Ration - x3 CPU/FSB Frequency Ratio - x13 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.325 CPU VID Special Control - Avove VID *114% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.70v DRAM Voltage Control - 2.80v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 08 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level2 Max Async Latency - 07.0 nano seconds Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 3dMark2003: 3dMark2005: Aquamark 3d: Everest Read: ========== short description: 215x13 @ 2797Mhz, 1.325 + 114% 2-2-8-2 @2.8v vdimm Share this post Link to post Share on other sites More sharing options...
jm76 Posted August 25, 2005 Posted August 25, 2005 LANPARTY UT nF4 SLI-D 704-2BT bios AMD Athlon 64 3000+ Venicer Socket 939 Processor Model ADA3000 DAA4BP – YBBLE 0525DPCW stepping Corsair TWINX2048-3200C2 2x1GB 1x eVGA Geforce 6600GT 128MB 128-bit GDDR3 PCI-Express x16 Video Card 2x Western Digital Caviar SE WD1600JD 160GB 7200 RPM 8MB Cache Serial ATA150 Hard Drive – non-Raid TOSHIBA Black 16X DVD-ROM 52X CD-R 32X CD-RW 52X CD-ROM 2M Cache IDE Combo Drive TOSHIBA Black 16X DVD+R 4X DVD+RW 5X DVD+R DL 12X DVD-R 4X DVD-RW 16X DVD-ROM 48X CD-R 24X CD-RW 48X CD-ROM 2M Cache IDE DVD Burner Antec SmartPower 2.0 SP-500 ATX12V 500W Power Supply ZALMAN CNPS7000B-CU 92mm 2 Ball Cooling Fan/Heatsink ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ration - 3 CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.425v CPU VID Control - 1.425v CPU VID Special Control - Above VID * 104% LDT Voltage Control - 1.40v Chip Set Voltage Control - 1.80v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 150 (DRAM/FSB:3/04) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 14 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - 8 Read Preamble Time - 6 IdleCycle Limit - 32 Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.26 + A64Tweaker: 3dMark2003: 3dMark2005: Aquamark 3d: Everest Memory Read ========== short description: 270x9 @ 2430Mhz, 1.425v + 104% 2-3-6-3 @ 2.7v vdimm on a 12 divider Share this post Link to post Share on other sites More sharing options...
hifi Posted August 26, 2005 Posted August 26, 2005 DFI Lanparty NF4 Ultra-D - 06/23-05 BIOS Athlon 64 3700+ San Diego 4x512mb OCZ PC4000 VX Gold EL Nvidia GeForce 7800 GTX 2X WD 74GB Raptors RAID-0 Plextor 716 DVD/CD Enermax 600W SLI Koolance EXOS-AL w/GPU L60 and CPU-300 Waterblocks ========== Genie BIOS Settings: FSB Bus Frequency - 250 LDT/FSB Frequency Ratio - 4X CPU/FSB Frequency Ratio - 11X PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.50V CPU VID Control - 1.35V CPU VID Special Control - Above VID * 123% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.30v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/01) Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.0 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 02 Bus Clocks Refresh Period (Tref) - 3120 Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 8 DRAM Data Drive Strength - Level 2 Max Async Latency - 7ns DRAM Response Time - Fastest Read Preamble Time - 6.0ns IdleCycle Limit - 16 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) Prime95+3DMark01+CPU-Z 1.29 (Vcore is wrong it is 1.6V) http://i22.photobucket.com/albums/b306/ana...E95_3DM2001.jpg 3DMark05: http://i22.photobucket.com/albums/b306/ana...gs/3DMark05.jpg 3DMark03: http://i22.photobucket.com/albums/b306/ana...gs/3DMark03.jpg Aquamark 3: http://i22.photobucket.com/albums/b306/ana...3/2Gigs/AQ3.jpg Everest Read: http://i22.photobucket.com/albums/b306/ana...erest_Read2.jpg Everest Write: http://i22.photobucket.com/albums/b306/ana...erest_Write.jpg Everest Latency: http://i22.photobucket.com/albums/b306/ana...est_Latency.jpg short description: 4X512 OCZ PC4000 VX Gold EL 250x11 @ 2750Mhz, 1.350v + 123% 2-2-6-2 @ 3.3v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted August 30, 2005 Posted August 30, 2005 DFI LANPARTY nF4 Ultra-D - 7/04-2 BigToe BIOS AMD Athlon64 3000+ Venice 2x512MB Centon Advance LL (tccd) XFX 7800GTX 256MB, 496/1251 77.77 drivers Maxtor 160GB IDE hdd (8MB cache) ASUS CD-S520/A5 Black IDE CD-ROM Drive OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - AUTO PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.00v DRAM Configuration Settings: DRAM Frequency Set - 180=RAM/FSB:09/10 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 2 Max Async Latency - 8.0 Nano Seconds DRAM Response Time - Fast Read Preamble Time - 6.0 Nano Seconds IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/mrkun/ross-1.jpg 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 300x9 @ 2700Mhz, 1.400v + 113% 2.5-4-8-4 @ 3.0v vdimm thanks to mrkun of the DFI-Street forum for letting me run this on his motherboard, cpu, and my memory! Share this post Link to post Share on other sites More sharing options...
century child Posted September 2, 2005 Posted September 2, 2005 DFI LanParty UT nF4 SLI-DR - 7/04-2 BigToe BIOS AMD "San Diego" 3700+ CABHE 0525UPMW 2048MB Corsair XMS PC3200 Dual Channel Kit Twinx2048-3200c2 XFX Geforce 7800GTX 450 MHz Core 1250 MHz Mem Creative Sound Blaster Audigy 2 ZS Platinum Pro Be Quiet! Blackline BQT P5-520W-S1.3 520 Watt PSU 2x WD Raptor WD740GD 74GB 10,000 RPM SATA HDD - RAID0 NVRAID controller LITEON LDW-411S Overclocked/Firmware Hacked to 811S IDE DVD Burner Plextor Premium IDE CD Burner Cooler Master Stacker STC-TO1-UW Case Danger Den TDX Block 1/2" Fittings 12V DD-D4 Pump Black Ice Xtreme Radiator w/Papst 74CFM Fan and shroud Innovatek Fass-O-Matic Reservoir ClearFlex 60 1/2" ID Tubing ---------------------------------- ---------------------------------- Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - 11.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - Startup CPU VID Control - 1.325v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 2.70v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Auto CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 03 Bus Clocks Min RAS# active time (Tras) - 06 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 09 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - Auto Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ------------------------------ ------------------------------ Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://img320.imageshack.us/img320/7613/12jq.jpg 3dMark2003: http://img60.imageshack.us/img60/3015/23cf1.jpg 3dMark2005: http://img17.imageshack.us/img17/7282/36if.jpg Aquamark 3d: http://img167.imageshack.us/img167/5844/41sv.jpg -------------------------------- -------------------------------- short description: 240x11 @ 2640Mhz, 1.325v + 113% 2.5-3-6-3 @ 2.7v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted September 3, 2005 Posted September 3, 2005 DFI LANPARTY nF4 Ultra-D - 6/23-3 BIOS , IOSS Bios Savior RD1-PMC4 Venice 3200 ADA3200BPBOX Stepping=LBBLE 0515FPBW (Using stock cooler this time) OCZ PC4200EL 2x512mb = 1024mb's TCC5 in slots 24 Powercolor X850Xt vgpu + vdd mods , ZALMAN VF700-CU 2 Ball VGA COOLER.. Official Cat 5.8's 570-621 Maxtor DiamondMax 10 120GB 3.5" Serial ATA150 Hard Drive ENERMAX Whisper II EG565P-VE FMA(24P) ATX12V 535W * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 300 LDT/FSB Frequency Ration - 3x CPU/FSB Frequency Ratio - 9 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.45v CPU VID Control - 1.275v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.30v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.0v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:1/1) Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 13 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 1 Max Async Latency - 9 DRAM Response Time - Fast Read Preamble Time - 5.5 IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + 2x CPU-Z + MBM : 3dMark2003 : 3dMark2005 : Aquamark 3d: Everest : ========== short description: 300x9@ 2700Mhz, 1.275v + 123% 2x512mb's @300mhz 2.5-4-8-3 @ 3v vdimm Share this post Link to post Share on other sites More sharing options...
Angry_Games Posted September 3, 2005 Posted September 3, 2005 DFI LANPARTY nF4 SLI-DR - 7/04-2 BigToe BIOS AMD Athlon64 4000+ San Diego 4x1024MB OCZ PC4000 (OCZ5002048ELGE-K) 2 - Chaintech 6600GT SLI, 560/1171 77.77 drivers[/color] 2 - Western Digital Raptor 10,000RPM 36GB SATA hdd ASUS CD-S520/A5 Black IDE CD-ROM Drive OCZ PowerStream OCZ600ADJ ATX 600W Power Supply - Retail * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 240 LDT/FSB Frequency Ratio - AUTO CPU/FSB Frequency Ratio - x 12.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.500v CPU VID Control - 1.400v CPU VID Special Control - Above VID * 113% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 2.90v DRAM Configuration Settings: DRAM Frequency Set - 200=RAM/FSB:01/01 Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 3.0 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 09 Bus Clocks Row precharge time (Trp) - 04 Bus Clocks Row Cycle time (Trc) - 13 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - AUTO Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto Max Async Latency - Auto DRAM Response Time - Fast Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 + 3dMark2001SE + CPU-Z 1.29 + Everest 2.01: http://www.angrygames.com/ocdb/angry/nf4/4...gb_240x12-1.jpg 3dMark2003: 3dMark2005: Aquamark 3d: ========== short description: 240x12 @ 2880Mhz, 1.400v + 113% 3.0-4-9-4 @ 2.9v vdimm Share this post Link to post Share on other sites More sharing options...
THunDA Posted September 4, 2005 Posted September 4, 2005 DFI LANPARTY nF4 Ultra-D - 6/23-3 BIOS , IOSS Bios Savior RD1-PMC4 Venice 3200 ADA3200BPBOX Stepping=LBBLE 0515FPBW (SLK948 with 92mm panaflo M1A) OCZ PC4200EL 4x512mb = 2048mb's TCC5 Powercolor X850Xt vgpu + vdd mods , ZALMAN VF700-CU 2 Ball VGA COOLER.. Official Cat 5.8's 570-621 Maxtor DiamondMax 10 120GB 3.5" Serial ATA150 Hard Drive ENERMAX Whisper II EG565P-VE FMA(24P) ATX12V 535W * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ration - 3x CPU/FSB Frequency Ratio - 10 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - 1.45v CPU VID Control - 1.275v CPU VID Special Control - Avove VID * 123% LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.50v DRAM Voltage Control - 3.0v DRAM Configuration Settings: DRAM Frequency Set - 200 (DRAM/FSB:01/01) Command Per Clock (CPC) - Disable CAS Latency Control (Tcl) - 2.5 RAS# to CAS# delay (Trcd) - 04 Bus Clocks Min RAS# active time (Tras) - 08 Bus Clocks Row precharge time (Trp) - 03 Bus Clocks Row Cycle time (Trc) - 8 Bus Clocks Row refresh cyc time (Trfc) - 16 Bus Clocks Row to Row delay (Trrd) - 03 Bus Clocks Write recovery time (Twr) - 03 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 4708 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Level 7 DRAM Data Drive Strength - Level 1 Max Async Latency - 7 DRAM Response Time - Fast Read Preamble Time - 5.5 IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(8 Bursts) ========== Prime95 + 3dMark2001SE + 2x CPU-Z + MBM + Everest : 3dMark2003 : 3dMark2005 : Aquamark 3d: ========== short description: 270x10@ 2700Mhz, 1.275v + 123% 4x512mb's @270mhz 2.5-4-8-3 @ 3.0v vdimm Share this post Link to post Share on other sites More sharing options...
silicon Posted September 17, 2005 Posted September 17, 2005 DFI LANPARTY nF4 Ultra-D - 7/02-2 BIOS AMD Athlon64 3200+ Venice 2x512MB OCZ EL DDR PC3200 Gold Edition (Winbond UTT BH-5) XFX Nvidia Geforce 6600 GT 128MB GDDR3, 564/1130 - 77.77 drivers Seagate 250GB 7200.8 SATA hdd Lite-on DVDRW SOHW-1633S Antec SmartPower 2.0 ATX 500W Power Supply - Retail * * * * ========== Genie BIOS Settings: FSB Bus Frequency - 270 LDT/FSB Frequency Ratio - X 4.0 CPU/FSB Frequency Ratio - X 10.0 PCI eXpress Frequency - 100Mhz CPU VID StartUp Value - StartUp CPU VID Control - 1.500v CPU VID Special Control - Auto LDT Voltage Control - 1.20v Chip Set Voltage Control - 1.60v DRAM Voltage Control - 3.00v DRAM Configuration Settings: DRAM Frequency Set - 166=RAM/FSB:05/06 Command Per Clock (CPC) - Enable CAS Latency Control (Tcl) - 2 RAS# to CAS# delay (Trcd) - 02 Bus Clocks Min RAS# active time (Tras) - 05 Bus Clocks Row precharge time (Trp) - 02 Bus Clocks Row Cycle time (Trc) - 07 Bus Clocks Row refresh cyc time (Trfc) - Auto Row to Row delay (Trrd) - 02 Bus Clocks Write recovery time (Twr) - 02 Bus Clocks Write to Read delay (Twtr) - 02 Bus Clocks Read to Write delay (Trwt) - 03 Bus Clocks Refresh Period (Tref) - 3120 Cycles Write CAS Latency (Twcl) - Auto DRAM Bank Interleave - Enabled DQS Skew Control - Auto DQS Skew Value - 0 DRAM Drive Strength - Auto DRAM Data Drive Strength - Auto? Max Async Latency - Auto DRAM Response Time - Normal Read Preamble Time - Auto IdleCycle Limit - 256 Cycles Dynamic Counter - Disable R/W Queue Bypass - 16 x Bypass Max - 07 x 32 Byte Granularity - Disable(4 Bursts) ========== Prime95 v24.14 + 3dMark2001SE Build 330 + CPU-Z v1.3: 3dMark2003 v3.6.0: 3dMark2005 v1.2.0: Aquamark 3d: Everest v2.20.405: http://img360.imageshack.us/img360/4219/everesthome0nk.png Everest v2.20.405 and ITE Smart Guardian (Temperatures at idle): ========== short description: 270x10 @ 2700Mhz, 1.500v 2-2-2-5 @ 3.0v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now