Angry_Games Posted October 11, 2007 Posted October 11, 2007 DFI LANPARTY nF4 Ultra-D (modded to SLI-D) (3/29/2006 BIOS) AMD X2 3800+ dual core 2x1024MB Corsair XMS4000 PT ATI X1900XT 512MB PCI-E, 7.8 CAT drivers 36GB Western Digital Raptor 10,000RPM SATA hdd Asus 52x Quiet-Trak CD-ROM OCZ Powerstream 520w Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 250 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - Auto PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - Auto CPU VID Special Control....................... - VID +110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.90v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 03 Bus Clocks RAS# to CAS# delay (Trcd)..................... - 04 Bus Clocks Min RAS# active time (Tras)................... - 09 Bus Clocks Row precharge time (Trp)...................... - 04 Bus Clocks Row Cycle time (Trc).......................... - 12 Bus Clocks Row refresh cyc time (Trfc)................... - 24 Bus Clocks Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Normal Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: http://www.angrygames.com/ocdb/angry/nf4/3...x2_250x10-1.gif 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark 3d: ========== short description: 250x10 @ 2500Mhz 3-4-9-4 @ 2.90v vdimm Share this post Link to post Share on other sites More sharing options...
leviathan69 Posted October 21, 2007 Posted October 21, 2007 DFI LANPARTY nF4 (3/29/06 BIOS) AMD Opteron 180 Dual core Zalman CNPS9700 Led CPU HSF 2x256mb Corsair CMX256A-3200C2 XFX GeForce 8800GTS 580M 320MB DDR3, 621/1053 6.14.011.6371 drivers 2xMaxtor 6L100MO Raid 0 186GB HDD Lite-On DVDRW LH-20A1H DVD Drive Antec TruePower 480w PSU ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 300 LDT/FSB Frequency Ratio....................... - Auto CPU/FSB Frequency Ratio....................... - 10 PCI eXpress Frequency......................... - 105Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.325V CPU VID Special Control....................... - Above VID * 126% LDT Voltage Control........................... - 1.40v Chip Set Voltage Control...................... - 1.70v DRAM Voltage Control.......................... - 3.0v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 140=RAM/FSB:7/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 07 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - Auto Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - Auto Write recovery time (Twr)..................... - Auto Write to Read delay (Twtr).................... - Auto Read to Write delay (Trwt).................... - Auto Refresh Period (Tref)......................... - Auto Write CAS Latency (Twcl)...................... - Auto DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 4(Reduce 00%) Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Prime95 + 3dMark2001SE + CPU-Z + Everest 2.20: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 300 x 10: 3000mhz, 1.62Vcore 2-3-3-7 3.0Vdimm Share this post Link to post Share on other sites More sharing options...
n_w95482 Posted October 27, 2007 Posted October 27, 2007 DFI LANPARTY nF4 SLI-DR Expert (406-BTA BIOS) AMD Opteron 165 (CCBBE 0615 EPMW) DD TDX waterblock, Swiftech MCR220-QP radiator, Laing D5 pump 2x1024MB OCZ PC4000EB (OCZ5001024EBPE) eVGA GeForce 7800 GTX (256 MB), 491/650, 94.24 drivers 150GB Western Digital Raptor, 2x500 GB WD RE2 RAID1 on 3ware 9650SE-4LPML PCIe SATA controller Lite-On LH-20A1L SATA burner, LG GDR8164B DVD-ROM OCZ GameXStream 700w Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 334 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.475v CPU VID Control............................... - 1.475 CPU VID Special Control....................... - Above VID * 104.8% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.52v DRAM Voltage Control.......................... - 2.74v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 09 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disabled DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 8 DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) Max Async Latency............................. - 8ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 5ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 06 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3DMark2001SE + CPU-Z (had 16x.xx FW installed w/2k1, dropped score by ~1050 vs 94.24): 3DMark2003: 3DMark2005: 3DMark 2006: AquaMark3: ========== short description: 334x9 @ 3007 MHz, 1.54v 3-3-2-8 @ 2.74v vdimm Share this post Link to post Share on other sites More sharing options...
uncle john Posted October 29, 2007 Posted October 29, 2007 DFI LANPARTY nF4 Ultra-D (7/04-2bta BIOS) AMD X2 4200+ LCBQE 0723VPMW 2x1GB OCZ PC4000EB (OCZ5001024EBPE-K) BFG 7950GT OC, (stock) 320GB Seagate Barracuda 7200.10 ST3320620AS SATA hdd Antec Neo HE 550 ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 323 LDT/FSB Frequency Ratio....................... - 3 CPU/FSB Frequency Ratio....................... - 9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - auto CPU VID Control............................... - 1.375v CPU VID Special Control....................... - auto LDT Voltage Control........................... - 1.30v Chip Set Voltage Control...................... - 1.60v DRAM Voltage Control.......................... - 2.80v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.5 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 7 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 9 Bus Clocks Row refresh cyc time (Trfc)................... - 12 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Normal 4 (Level 8) DRAM Data Drive Strength...................... - Level 2 Max Async Latency............................. - 8 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6.5 ns IdleCycle Limit............................... - 128 Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== short description: 323x9 @ 2906Mhz, 1.375v 2.5-3-7-2 @ 2.80v vdimm Share this post Link to post Share on other sites More sharing options...
ahmadka Posted November 18, 2007 Posted November 18, 2007 DFI LANPARTY nF4 SLI-DR (11/14/2005) AMD Opteron 165 2GB OCZ PC4000 Gold Edition Dual Channel Kit (OCZ5002048ELGE-K) eVGA GeForce 7900GT CO, 500/1500 169.01 drivers 250GB Western Digital Caviar 7,200RPM SATA 3.0Gb/s HDD LITE-ON Black LightScribe 5x DVD-RAM Burner OCZ PowerStream 520w SLI Power Supply * * * * ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 310 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.375v CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.60v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 166=RAM/FSB:05/06 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 07 Bus Clocks Row refresh cyc time (Trfc)................... - 14 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Level 08 DRAM Data Drive Strength...................... - Level 1 Max Async Latency............................. - 8.0ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 ns IdleCycle Limit............................... - Auto Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos + 3dMark2001SE + 2x CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 310x9 @ 2794Mhz, 1.375v vCore Voltage 3-4-4-8-2T @ 2.60v vDimm Share this post Link to post Share on other sites More sharing options...
loggan26 Posted November 28, 2007 Posted November 28, 2007 DFI LANPARTY NF4 Ultra-D (Merlin's 23.11.07) AMD 165 Opteron Stock Opteron Heatsink 2x1024MB OCZ GX XTC PC4000 ATI Radeon X1950pro 256mb 120GB Maxtor Diamond Max HDD Pata Evercool VC-RE Chipset Syncmaster 225BW CoolerMaster Stacker 830 OCZ GameXstream 700W Sli ***************** Genie BIOS Settings: FSB Bus Frequency............................. - 326 LDT/FSB Frequency Ratio....................... - x3 CPU/FSB Frequency Ratio....................... - x9 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - StartUp CPU VID Control............................... - 1.400v CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.65v DRAM Configuration Settings: DRAM Frequency Set............................ - 150=RAM/FSB:03/04 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 4 Min RAS# active time (Tras)................... - 8 Row precharge time (Trp)...................... - 4 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 04 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles Odd Divisor Correct........................... - Disable DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Level 1 (Reduce 50%) Max Async Latency............................. - 9ns DRAM Response Time............................ - Fastest Read Preamble Time............................ - 6.0ns IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) ************** Dual Prime95 + 3dMark2001SE + CPU-Z: 3dMark2003: 3dMark2005: 3dMark2006: Aquamark Short Description: 326x9 @ 2934Mhz, 1.400v 3-4-8-4 @ 2.65v vdimm Logan Share this post Link to post Share on other sites More sharing options...
centy Posted December 2, 2007 Posted December 2, 2007 DFI LANPARTY nF4 SLI-D (704-2BT BIOS) AMD A64 3700+ San Diego KACAE 0546EPAW 2x1024MB G.Skill HX PC3200(DDR400) (F1-3200BIU2-2GBHX) PNY GeForce 7800GT 256MB GDDR3, 400/1000Mhz Forceware 163.75 WHQL drivers 250GB Seagate Baracuda 7200.8 7,200RPM SATA NCQ 8MB Cache hdd (ST3250823AS) NEC ND4550A DVD-RAM SuperMulti Drive 2MB Cache Tagan TG530-U15 530w ATX v2.01 Modular Power Supply ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 311 LDT/FSB Frequency Ratio....................... - 3x CPU/FSB Frequency Ratio....................... - 9x PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.500v CPU VID Control............................... - 1.325v CPU VID Special Control....................... - 113% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v DRAM Voltage adjustment +0.3v................. - Disabled[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 150 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 3 RAS# to CAS# delay (Trcd)..................... - 3 Min RAS# active time (Tras)................... - 0 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - 7 Bus Clocks Row refresh cyc time (Trfc)................... - 13 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 02 Bus Clocks Write to Read delay (Twtr).................... - 01 Bus Clocks Read to Write delay (Trwt).................... - 02 Bus Clocks Refresh Period (Tref)......................... - 1032 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Weak 4 DRAM Data Drive Strength...................... - Level 3 Max Async Latency............................. - 7.0 ns DRAM Response Time............................ - Normal Read Preamble Time............................ - 6.0 ns IdleCycle Limit............................... - 16 Cycles Dynamic Counter............................... - Enabled R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== SP2004 + 3DMark 2001SE + CPUZ 3DMark 03 3DMark 05 3DMark 06 Aquamark 3 ========== short description: 311 x 9 = 2799MHz, 1.46v 3-3-0-2 @ 2.70 vdimm Share this post Link to post Share on other sites More sharing options...
SpeedEuphoria Posted February 6, 2008 Posted February 6, 2008 DFI LANPARTY nF4 Ultra D (04/06BTA BIOS) AMD Opteron 165 CCBWE 0536MPMW(1800Mhz/1mb L2 per core)+ NO IHS 2x512MB Patriot XBL PC4800(TCCD) EVGA GeForce 7600GT 256MB PCI-E 16x, 600/800 169.21 drivers 2x 74GB WD Raptor FLCO Sata hdds(raid0)+ 2x 80GB Hitachi Deskstar SataII hdds(raid0) Nec 3550A Dvd R/W(Ide1)+LiteOn SOHW-1213S Dvd R/W(Ide2) Thermaltake PurePower 460w Power Supply W0068(Not Recomended!!) ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 290 MHZ LDT/FSB Frequency Ratio....................... - x 3.0 CPU/FSB Frequency Ratio....................... - x 9.0 PCI eXpress Frequency......................... - 101Mhz CPU VID StartUp Value......................... - 1.45v CPU VID Control............................... - 1.325v CPU VID Special Control....................... - VID Special * 110% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v DRAM+.03V If it's not 3.2V.................... - Enable[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 140=RAM/FSB:07/10 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 2.0 RAS# to CAS# delay (Trcd)..................... - 2 Min RAS# active time (Tras)................... - 5 Row precharge time (Trp)...................... - 2 Row Cycle time (Trc).......................... - Auto Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - 03 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 03 Bus Clocks Refresh Period (Tref)......................... - 3120 Cycles DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - Auto DRAM Response Time............................ - Fast Read Preamble Time............................ - Auto IdleCycle Limit............................... - 32 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] ========== Orthos (SP2004) + 3dMark2001SE + 2x CPU-Z: 3dMark2003: 3dMark2005: 3dMark 2006: Aquamark 3: ========== short description: 290x9 @ 2610Mhz, 1.45v cpu 2-2-5-2 @ 2.73v vdimm Share this post Link to post Share on other sites More sharing options...
RHKCommander959 Posted February 14, 2008 Posted February 14, 2008 DFI CFX3200 DR/G AMD Athlon 3800x2 4x512mb DDR 510 2.5 3 3 7 Seagate 16mb 250gb HDD GeCube ATI HD 3850 512 LG IDE DVD-CD Burner Combo 2MB Cache thermaltake toughpower 750w modular http://valid.x86-secret.com/show_oc.php?id=258854 dont have time to resize.. you wouldnt be able to read 'em anyway if i did how do i reopen 3dr files fomr 3dmark06? still adding to it Share this post Link to post Share on other sites More sharing options...
freakyGameR Posted February 15, 2008 Posted February 15, 2008 DFI LANPARTY nF4 Ultra-D - BIOS 6/23/2005 AMD 64 X2 4200 (Manchester) 2x512kB L2 Cache, Bios (704-22V6) Bigtoe Tweaked 704-2A/Memtest v1.65 Added by Tmod Thermalright XP-90 and NMB Fans (3612KL-04W-B66) Thermalright HR-05 SLI Chipset Cooler G.SKILL F1-3200PHU2-2GBZX 2x1GB DDR400 PC3200, Model F1-3200PHU2-2GBZX Silverstone Strider 560w, Model ST56F Colorful Nvidia 8600GTS 256MB PCI-E x16 Video Card (745/1020) Seagate 250GB SATA II 7200RPM 16MB Cache HDD Lite-On DVD Writer + LG DVD ROM, Model SHM-165P6S + GDR-H30N Genie BIOS Settings: FSB Bus Frequency............................. - 266 LDT/FSB Frequency Ratio....................... - x4.0 CPU/FSB Frequency Ratio....................... - 10.0 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - 1.5v CPU VID Control............................... - 1.475v CPU VID Special Control....................... - Above VID *104% LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.70v DRAM Voltage Control.......................... - 2.80v [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 200=RAM/FSB:01/01 Command Per Clock (CPC)....................... - Enable CAS Latency Control (Tcl)..................... - 03 Bus Clocks RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 05 Bus Clocks Row precharge time (Trp)...................... - 02 Bus Clocks Row Cycle time (Trc).......................... - 15 Bus Clocks Row refresh cyc time (Trfc)................... - 17 Bus Clocks Row to Row delay (Trrd)....................... - 02 Bus Clocks Write recovery time (Twr)..................... - 03 Bus Clocks Write to Read delay (Twtr).................... - 02 Bus Clocks Read to Write delay (Trwt).................... - 04 Bus Clocks Refresh Period (Tref)......................... - Auto Write CAS Latency (Twcl)...................... - 1 DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Off DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Auto Max Async Latency............................. - 08.0 Nano Seconds DRAM Response Time............................ - Normal Read Preamble Time............................ - 06.0 Nano Seconds IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 04 x 32 Byte Granularity........................... - Disable(4 Bursts) [/color] Prime95 + 3DMark2001SE + CPU-Z: http://i62.photobucket.com/albums/h89/gmieroxx/post1.jpg 3DMark2003: http://i62.photobucket.com/albums/h89/gmieroxx/post2.jpg 3DMark2005: http://i62.photobucket.com/albums/h89/gmieroxx/post3.jpg 3DMark2006: http://i62.photobucket.com/albums/h89/gmieroxx/post4.jpg Aquamark3: http://i62.photobucket.com/albums/h89/gmieroxx/post5.jpg Short Description: 266x10 @ 2660Mhz, 1.475v + 104% 3-3-5-2 @ 2.8v vdimm Share this post Link to post Share on other sites More sharing options...
Guest SuppA-SnipA Posted February 16, 2008 Posted February 16, 2008 DFI LANPARTY nF4 NF4-D (xxx BIOS) AMD Athlon 4000+ 2x1024MB OCZ PC3200 (OCZ4002048PFDC-K)[/size] XFX GeForce 8600 GTS, 675 MHz / 1008MHz, 169.21 Drivers 160GB, 200GB Western Digital SATA hdd's and 30gb notebook hdd (osx86 Leopard) Samsung SH-182M DVD-RW drive Antec Truepower Trio 650Watt BIOS screenshots ========== [b]Genie BIOS Settings:[/b] [color=red] FSB Bus Frequency............................. - 246 LDT/FSB Frequency Ratio....................... - x 4 CPU/FSB Frequency Ratio....................... - x 11 PCI eXpress Frequency......................... - 100Mhz CPU VID StartUp Value......................... - Startup CPU VID Control............................... - 1.375 V CPU VID Special Control....................... - Auto LDT Voltage Control........................... - 1.20v Chip Set Voltage Control...................... - 1.50v DRAM Voltage Control.......................... - 2.70v[/color] [b]DRAM Configuration Settings:[/b] [color=red] DRAM Frequency Set............................ - 180=RAM/DRAM/FSB:9/10 CAS Latency Control (Tcl)..................... - 3.0 RAS# to CAS# delay (Trcd)..................... - 03 Bus Clocks Min RAS# active time (Tras)................... - 07 Bus Clocks Row precharge time (Trp)...................... - 03 Bus Clocks Row Cycle time (Trc).......................... - Auto Row refresh cyc time (Trfc)................... - Auto Row to Row delay (Trrd)....................... - Auto Write recovery time (Twr)..................... - Auto Write to Read delay (Twtr).................... - Auto Read to Write delay (Trwt).................... - Auto Refresh Period (Tref)......................... - Auto Write CAS Latency (Twcl)....................... - Auto DRAM Bank Interleave.......................... - Enabled DQS Skew Control.............................. - Auto DQS Skew Value................................ - 0 DRAM Drive Strength........................... - Auto DRAM Data Drive Strength...................... - Level 4 Max Async Latency............................. - 07.0 Nano Seconds Read Preamble Time............................ - Auto IdleCycle Limit............................... - 256 Cycles Dynamic Counter............................... - Disable R/W Queue Bypass.............................. - 16 x Bypass Max.................................... - 07 x 32 Byte Granularity........................... - Disable(8 Bursts) [/color] ========== Orthos + 3dMark2001SE + CPU-Z x2: 3dMark2003: 3dMark2005: 3dMark 2006: ========== short description: 246x11 @ 2706Mhz, CPU Vcore 1.375 3-3-3-7 @ 2.70v vdimm Share this post Link to post Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now